I ended up making a number of practice cuts. The first revealed that I hadn't tightened the screws on the edge guide enough. The second revealed that the design of the edge guide provided very little support at the end of a board, because of the cut-out for the router bit. In the "Getting Started in Woodworking" video, they had screwed a piece of hardwood to the edge-guide, to provide a continuous -- and longer -- bearing surface. I may do that myself, some day, but I didn't have the materials at hand, so I clamped some 2x4 scrap to the end of each board, to provide a continuous bearing surface past the ends. The two grooves in the long stretchers and the side groove in the short stretchers have identical layout. I made practice cuts in scrap until I had the edge guide set correctly, then I cut them all with that one setting. The bottom groove of the short stretchers uses a different setup, so it was back to the scrap, before cutting them.
Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.
Dip your toes in the world of woodworking with our week-long courses, and by the end of the week, you'll be swimming. During these intensive, week-long woodworking courses, you will benefit from the guidance of our expert furniture makers, learning the basic principles of woodwork and cabinet making to professional standards. Hone your technique with our classes and create precise, beautiful work with our expertise, equipment and advice at your disposal.

I built my first platform bed by following the steps mentioned in the tutorial and the end result was everything I expected. It was as beautiful as comfortable and strong. It only cost me around $60 to build this one from the scratch. And if I can build it, anyone can. What you need is a little bit of woodworking experience and a lot of confidence. Collect the items as suggested in the video and start working now.


Yea I had a friend who went the HD route and in after putting new braces up for the roof and an extra layer of plywood on the floor he gave up the fight and tore it down. We ended up building twice the shed that was 100 times more sturdy for less than he had invested in the first one. I would go any route that is the opposite way of HD or Lowes. Learn from this guy.
In ancient times, the woodworker’s bench consisted of a plank or split log with four splayed legs. Descendants of those benches are manufactured today, usually with a top of hardwood slabs glued together. The norm nowadays is four straight legs supporting the bulk above, often with braces and a shelf below. Despite the improvements, the linkage to Greek and Roman antecedents is still evident.
We follow many traditional standards because they impart the work ethic of doing things right, emphasizing quality, attention to detail, considering impact and longevity, and working to high standards for lasting work.  Our instructors are experienced craftspeople who recognize the value of passing on their skill set to the next generation of woodworkers.  We strive to invite you into our community by connecting you with others who have a passion for craftsmanship.  
Learn basic principles of working with wood while making your own carved wooden spoon. Topics covered include different types of wood, grain direction, carving, shaping, and food safe finishes. Through short demonstrations and lectures, we will use a combination of power and hand tools, exploring the material for its functionality as a creative medium. At the end of the workshop, students leave with a unique spoon, ready to use! All materials included.

This table top is also made from the hardest wood out of any manufacturer we reviewed: oak. In fairness, this can be both a blessing and a curse. The oak wood is extremely durable and noted for its lack of a porous nature. This means the top can withstand plenty of abuse from tool and workpieces. Moreover, you will not have to worry about liquids like lacquers and stains from being absorbed into the top. That said, the hard oak can also do a number on tool sharpness, dulling them prematurely if they are not carefully handled.
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.

2 - use a plunge router with a bottom bearing cuter bit such as this from rockler: http://www.rockler.com/product.cfm?page=25160&site=ROCKLER .... I thought to use the short one as I plunge it directly downward in the centre of the hole until the bearing reaches within the tabletop hole. I suppose one could use a long one, but the stubbiness seemed more practical (the big bearing ensured accuracy?)


Woodworking Workbenches are available in a variety of styles. Open Style Wood Workbenches feature a large work surface and a lower shelf. 2-1/4" thick maple top with maple plywood lower shelf. Open Style Wood Workbenches are available as a 2-station unit (28"W) or a 4-station unit (54"W). Open Style Auxiliary Workbenches are used for placement against walls. Shelf features a rear curb to keep contents in place. Solid maple top features angle iron front edge. Plywood shelf is open for maximum functionality. Solid maple legs. Environmentally-friendly UV finish. Units measure 24"D and are available in several lengths and heights. Mitre Box Benches ensure wood pieces are kept flat while mitres are cut. Bench is made using solid maple unit with environmentally-friendly UV finish. Holds a mitre saw up to 26"W and provides a 24" square work surface on both sides. Mitre Box Benches measure 33-3/4"H. Sheet Metal Workbenches are made with a 2-1/4" thick maple top and is protected on two long edges with 2" x 2" angle iron. Solid maple legs and stringers. Plywood shelves are designed to provide open storage of 30" metal sheets. Measures 40"D x 32"H and available in widths of 60" or 96".
Let me see if I can come up with a couple details. The table saw is a TS3660. So I have heard, this should be the center of your shop. My jointer is a 6 1/8" Jointer / Planer JP0610 which is 45 inches in length. My router table is the kreg router table that takes up a 24 x 32 inch footprint. My bench is roughly 30 x 70 inches and my bandsaw is 3' x3'. I have other tools as well such as a portable 12.5 Delta thickness planer in addition to a wall mounted dust collector. To add to the list, I am just about to get a 10 inch makita sliding compound miter saw. I can see how space will be eaten up quickly. Any ideas as to how arrange these tools in such a small shop? I will get pics a soon a I
Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.
I was a short-term member at Community Woodshop, but it's left a lasting impression on me! They have everything you need to build a variety of projects, and i definitely got some good use out of their quality equipment. The staff is very knowledgeable and friendly, and are always around to offer sound advice and to make sure you have a safe setup. I only discontinued my membership due

Not sure about Midwest but I have a 24 x 14 Game rm attached to my shop and I put a small window unit/heat pump in the wall. It stays comfortable all year round. It get really hot here and we had a several day in the 20's this winter but it's insulated well. That might not be as cold or as hot as in some places but the unit I haze does not run that often and has a low cost rating. I'm planning on putting a larger unit in the shop area even though I do like to work with the garage door open. The door is insulated so I can run A/c in there. Just my .02.
Every piece meets the highest grading standards for Every piece meets the highest grading standards for strength and appearance. This lumber is for a wide range of uses from framing of houses to basic interior finishing applications. Boards can also be used for carpentry hobbies furniture shelving and general finish work. This lumber can also be used in ...  More + Product Details Close
Having done all this, I'm not sure I'd do it this way again. It might well be faster to layout the positions with compass and straightedge directly onto the top. Either way, you'll want to use a scribe rather than a pencil. Scribe lines are hard to see, and impossible to photograph, but the scribe and compass points click into them, allowing a precision that pencils simply cannot match.

The reason I'd cut out the rectangles in the vise support was that I'd intended to put a benchdog hole through each, and I wanted the thickness of the top to be the same for all of the benchdog holes. Where I messed up was in not cutting out the ends, between the bolt tabs. I'd intended to put a benchdog hole through there, as well, but I'd forgotten to cut out the segments prior to glue0up.

The beauty of this project lies in the simplicity. All you need are 3 pieces of wood of your choice (though we must admit natural hardwoods will look incredible), sanding block, clamps, wood glue and finishing product. The hardest step of the whole tutorial is measuring – as always, measure 9 times, cut once! You wouldn’t want to finish your project and then realize it doesn’t have enough space to fit your DVD player, would you?

Stan Beckworth began his woodworking career in 1983. His wide experience in woodworking enables him to teach as a practicing master craftsman. He began woodworking because of a desire to work with his hands and pass some hand skills to his children. Some of the classes he teaches are the Finishing class, Relief Carving class, Foundational Classes and the Advanced Furniture courses, such as the Chest of Drawers and Rocking Chair classes. Stan has spent a lot of time learning about furniture finishes, as well as relief carving, studying with Mary May, a renowned woodcarver in South Carolina. When Stan isn’t teaching, he runs a small remodeling business at his home and builds and refinishes furniture for different clients. He has been commissioned to make furniture for several congressmen as well as refinishing furniture for past presidents. ”Being able to pass on practical skills that are useful for everyday application is what I love to do.”
1. You mention doing other hobbies which I assume means stuff scattered around for various projects. (Don't tell me you do one at a time or are a neat freak!!!) How tall are the side walls to the shed? How high do you shuffle stuff around, i.e. flipping things over, moving wood around, etc? I can't imagine trying to do that in my shed, even if it were 2 ft higher than it's 7 ft center height. If you could build a platform in front it may help, especially if you can put removable cover over it (to please HOA).
×