I wanted the left edge of the jaw of the front vise to be flush with the left edge of the top, the right edge with the left edge of the left front leg. So the amount of overhang on the left depends upon the width of the front vise jaw. The width of the jaw is, at a minimum, the width of the plate that supports it, but it's normal to make the jaw extend a bit beyond the plate. How far? The more it extends, the deeper a bite you can take with the edge of the vise, when, for example, you are clamping the side of a board being held vertically. But the more it extends, the less support it has. I decided to extend by 1-12", which gives me a 2-1/2" bite, and which should still provide solid support, given that the jaw is 1-1/2" thick. This means the top needs a left overhang of 12-1/4".
Require the woodworker to be able to read the plans and to transfer images and dimensions from the plan to the lumber. The wood has been planed and all glued panels are completed unless over 14 inches. If panel required is over 14 inches, one glue seam will be required. The woodworker needs to be able to do some cutting, jointing, assembling and finishing. White Kits do not require planing. White Kits supply all of the needed hand-selected dimensioned lumber, but woodworking knowledge and tools will be useful to complete the project successfully.
When the top is done, we want the edged MDF and the oak countertop to have exactly the same dimensions, and for their width to exactly match the width of the base.I could see three ways of doing this: 1, join the MDF to the countertop and use my belt sander to sand down their joined edges to match the base; 2, join the MDF to the countertop and use a hand plane to plane down their joined edges to match the base; or 3, use a flush-trim bit against a straight edge to route the MDF to the width of the base, then join the MDF to the countertop and use the flush-trim bit to route the countertop to match the MDF.
The procedure is very easy to understand and follow for anyone with a little woodworking knowledge. Make sure to collect all the items you need before you start with the project. You may even ask Tracy your queries directly in the comment section of the tutorial post. Or you can ask them here. Either way, I hope that you manage to build this one nicely.
In the middle third of the course, you’ll build a tool tote that features dovetails joining bottom-to-end boards; rabbeted and copper-nail pinned side boards; shaped end panels and curved handles passing through angled mortises. This joiner’s tote also features a lift-out box for layout tools with lapped (or optionally dovetailed) corners and a sliding lid.
For most of the course, we'll be heavily focused on developing your skills using hand tools. As a developing woodworker, there is no substitute for putting in the hours of direct hands on practice it takes to gain an intuitive understanding of wood. The early part of this course focuses on working with hand tools as we believe they bring you closer to wood as a material.  You can rip a board on a table saw with out much thought to the wood itself, but you will understand much more about grain if you rip a board with a hand saw.  As the course progresses, machine processes are introduced as a pragmatic aid in expediting projects.  
The holes we want to mark are the holes through which the threaded rod connecting the two legs will run. This threaded rod will run through the 3/8" groove along the bottom of the short stretchers,. The hole for the upper stretcher has to be positioned so that when the rod is running through this groove, the top of the short stretcher is even with the top of the legs. The most precise way I've found for marking the position of this hole is to use a dowel center. Fit the dowel center into the bottom groove, line up the stretcher, and bang on the end with a rubber mallet. The dowel center will leave a mark indicating the center of the hole.

Be careful. Single 24x60" sheets of 3/4" MDF are pretty easy to lift. A doubled sheet is manageable. The countertop - 24x72" panel of 1-1/2" oak - weighs something over 100 pounds. It takes real care to lift safely. The joined top - 3" thick of oak and MDF - is past the range that can be lifted safely by one person. Don't try. Get a friend to help, or rig a block-and-tackle.

Place sounds amazing. Receptionist was rude. Sarcastic remarks were not necessary. I called regarding the private lessons. And was told that they "can't hold my hand to do the work". The person made the statement not allowing me to finish saying that I have experience with wood work. I was really upset by the statement. He did not seem interested in having me as a client/student.
Turning an old door into a photo frame is another easy woodwork project. All you need is an old door and some woodworking tools and items. I am here sharing the link to the source tutorial that explains the step by step procedure for building a picture frame from an old wooden door. This tutorial was originally written by Tracy Snyder at athomewithsweett.blogspot.com who also tells you what items you may need and where to find them. If you haven’t already got an old door, you can purchase one from websites like Craigslist.
Assemble the vises, for the final time. You'll not be taking them off again, so tighten everything down, and attach the endplate to the ends of the screw and guide rods. Then mark and drill benchdog holes in the outer jaws inline with the benchdog holes in the top. Generally, through-holes are preferred for benchdogs, so that they don't collect sawdust and gunk. With these vises, that isn't possible, there are screws and guide rods in the way. I drilled them just deep enough to hold a Veritas Bench Pony (their reduced-height benchdog), without it sinking to where I can't get a grip to remove it. Rockler sells some very inexpensive plastic benchdogs that can't be adjusted for height, and aren't as strong as metal or wooden dogs, that I intend to keep in the holes full-time, to keep sawdust from collecting in them.
You can transfer a graphic on any wood piece of your choice, including a frame, top of a table, etc. The surface should be clean and big enough for the graphic paper. I am also sharing a video tutorial here that explains in detail the process of transferring any graphic to a wooden surface using a freezer paper. Just gather the items you need and follow this video to carve your favorite designs on your favorite wood items.
Building a Wooden Office Desk Organizer is an easy task for a professional woodworker, but not so much for normal people like you and me. But that doesn’t mean you cannot do this. Two years ago, I had almost no woodworking experience, but now I make most of my household and office wooden items by myself. This saves me a lot of money. And believe me when I say this; you can also manage to make wonderful wood items with a little practice and some woodworking experience.
Windsor Design is an interesting brand in that it is not actually its own company. Instead, Windsor Design is one of the in-house brands sold by Harbor Freight. While it may be a store brand, that should not dissuade you at all as Harbor Freight is known for selling some of the best products available for all fields of construction. Granted, this may not strictly be the best table available, but it does provide a solid mix of features to make it a good value.
Whether you’re setting up a new shop or upgrading your old one, a good, sturdy workbench will almost surely be central to your plans. We can help. Our editors and contributors have produced more than two dozen articles and videos about benches and assembly tables. We’ve included everything from a simple but workable plywood bench to a classic hardwood bench complete with vises. You’ll also find full project plans, as well as tips for installing vises, making your bench portable, adding storage, and more. Some of our workbench plans are free, and the rest can be purchased in our store (check the links below).

If the holes of the first jaw are in the proper position, drill holes in the same locations on the other jaw. I lined the drilled jaw on top of the undrilled jaw, clamped things down, and then drilled about 1/4" into the undrilled jaw, to mark the location. Then I removed the drilled jaw and drilled out the marked locations the same way I did the first.


I’ve built workbenches with more than 100 students. In every class, there’s one guy who wants to put a vise on every corner of the bench. Not because it’s a partner’s bench for two people. Just because he wants it that way. While I support your freedom to choose, I also don’t want to spend two weeks installing complex tail-vise hardware on your bench when we could be building furniture instead.
We have 4 newly expanded Classrooms, 3 state of the art labs with over $275,000 of new machinery, and $600,000 spent on new exhaust and compressed air systems. We have 4 new CNC production machines, a Haas VF-3 CNC Router and a NEWCNC 4×8 multi head machine and 2 Laguna IQ Routers. Even our shop stools (with cushioned backs) are brand new. We have new course offerings such as our Computer Design Sketchup Class and 8 new Certificate Programs you can choose from.
Those bums even have a stipulation that you can't connect any utilities to a shed. My plan is to adhere to the letter of the law if not the spirit. I plan to run a buried 20 amp power line out to the shed (this will be done professionally and properly according to whatever is required by the law), but it will require a manual connection to a junction box on the outside of my house to complete the circuit. That way, I can argue that the electrical connection is only temporary and is little more than a safe and buried version of an extension cord.
×