WoodSkills and Norman Pirollo offer online woodworking classes, woodworking plans, video lectures and woodworking tutorials. The classes and courses provide detailed and comprehensive step by step sequences for woodworking skill-building. Each woodworking class and tutorial is based on actual furniture making expertise. As founder of  White Mountain Design , Refined Edge Design , WoodSkills and Pirollo Design, I bring to you two decades of knowledge in furniture making. In recent years, I have authored three woodworking books:
Put the countertop on the base, put the MDF on top of the countertop, and line up the marks you drew on each end of the MDF with the countertop below it. When you have it lined up, clamp things down, and route the edge of the MDF using a 1-1/2" or longer flush-trim bit, with the depth adjusted so the bearing rides on the countertop. I clamped a couple of scraps of doubled MDF at each end to give the router base something extra to ride on at the ends.

Applying the oil is easy. Put on some vinyl gloves, pour some oil in a bowl, take a piece of clean cotton cloth the size of washcloth or smaller, dip it in the oil, and apply it to the wood. You want the wood to be wet., you're not trying to rub it in until it's dry. Apply oil to the entire surface, and then go over it looking for dry spots, applying more oil as needed. After fifteen minutes of keeping it wet, let it sit for another fifteen minutes. Then apply another coat of oil, and let it sit for another fifteen minutes.


My advice? Don't do this. If you have jointer and a planer, use them. If you don't, seriously consider using dimensional lumber that has already been planed and sanded. If you are going to try to clean up construction lumber by hand, using a hand plane is a lot faster and more pleasant than using a belt sander. Except, of course, that to do a good job of planing a board you need a solid bench to hold the board, and you don't have a bench, yet.
Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
Quality is what we do, YOU will do it too, from day one. We will teach you all stages from choosing hand tools, to picking out wood, to developing your drawings, and building a portfolio of work. There are lots of workshop schools, courses, and magazines that are great for showing you an amateur way of getting a good result. An amateur has no excuse for poor work other than lack of understanding, the amateur has all day to get it right, the professional has not. They must do it right, first time, every day.
In general, students in the certificate and degree programs learn how to understand and create their own shop drawings and design custom cabinetry. In the process, they also find out how to use the same tools and machines employed in the woodworking business and assemble cabinets according to industry standards. Additional program topics include the use of contemporary hardware in design.
Well, not these plans. You have the option of building a very functional and spacious lean-to shed on different foundations. Your foundation choices are: concrete slab, a wooden floor supported by concrete piers, or a wooden floor supported by skids. That lost option also means that your lean-to could be mobile as well so you won’t have to decide where you want to permanently put it.
to allow 9' at the peak, I like a "shed style" roof, but that may not fly in your HOA.I'd put double doors on or one large one, pour a slab, or use patio blocks then lay down Wolman. plywood for a floor, I would use foam insulating board everywhere I could, walls, floor and ceiling. A few bin type windows or sliders would let in light and fresh air. If you can't get away with your wiring idea, I would use a HD 30 amp twist lock extension cord with an "outside weatherproof outlet" mounted on the home professionally installed for code, 2- 8' long flouresent lights, and a 20 amp outlet inside for a heater and dehumidifier. Dehumidifiers draw about 5-6 amps. You might be better off with a small 6000 BTU window or wall mounted AC unit,( $100 on sale at the Depot), it will take the moisture out of the air and cool it as well in the summer. I'd use thin wall conduit around the shop with about 4 double duplex boxes. You may be able to bring 220v. in and then split into 2-120v circuits. If you make ANY dust in this confined space you must first catch it with a shop vac, then filter the air, and wear a mask. A bathroom ventilator fan would exchange the air and be quiet. A slab in front would allow sawing outside weather permitting. A roll up canopy over the door way would provide "shade" and rain protection. I know this sounds like a lot of work, but I know you can do it if you try. You can get plenty of "free" advice here and from an expert close to you. My neighbor enlisted the help of a handyman for building his 2 sheds and they became friends and did tool swaps and labor trades for time worked. My advice to you.. go 4 it! bill
The holes we want to mark are the holes through which the threaded rod connecting the two legs will run. This threaded rod will run through the 3/8" groove along the bottom of the short stretchers,. The hole for the upper stretcher has to be positioned so that when the rod is running through this groove, the top of the short stretcher is even with the top of the legs. The most precise way I've found for marking the position of this hole is to use a dowel center. Fit the dowel center into the bottom groove, line up the stretcher, and bang on the end with a rubber mallet. The dowel center will leave a mark indicating the center of the hole.

I really like this. I've been busy designing my own workbench to replace the ropey old thing I currently use. You've made me reconsider exactly what I need a bench for - I think I've been more than a little seduced by the idea of a beautiful hardwood bench when, if I'm honest, I don't need one. My cash would be better spend on timber for furniture projects that my family can enjoy rather than a wonderful workbench that I can only use on the weekends.
When the holes were complete, I flipped the legs and drilled the countersinks with a 1" Forstner bit. Trying to drill a countersink when the center was already drilled would be impossible with a spade bit or an auger, but Forstner bits are guided by their edges, not their center, so they can handle this job. On thing about Forstners, though -- they have a tendency to skitter around a bit when starting, before they bite. An easy fix for this is to drill a hole through a piece of ply, and to clamp that to your work, creating a jig that will prevent the bit from drilling in the wrong spot.
Much like the dimensions of a bench’s tabletop, the weight capacity will similarly affect what size of projects you can work on with your bench. A common weight capacity sits between 220 to 250 pounds. While this is okay, it will limit some heavier projects. Ideally, you should shoot for 300 pounds, though some benches can offer 500 pounds of weight capacity or more.

This bench suffers from no such limitations as it provides an incredibly solid and stable workspace, albeit in a somewhat stripped down version. In terms of performance, Sjobergs tops our list at providing 80 lbs of weight capacity. This is one of the more quantifiable measurements to determine the quality of a work bench’s craftsmanship. This is achieved by using thick pieces of European birch wood and working it without using lower end joints – like butt joints.


After I left the magazine for a new job, I did all of my woodworking in my small two-car garage, but it was a struggle. Power, lighting, and temperature control were limited. And because I shared space with our cars I was always moving machines around, often while in the middle of a project. On top of that, my tool and machine collection had long since eclipsed the space. For all these reasons, fixing up the garage wasn’t an option. My finished basement is a family room, so it was out, too. An addition to the home or a stand-alone building would have been too expensive. I had to find a better path to a shop.
×