I ended up making a number of practice cuts. The first revealed that I hadn't tightened the screws on the edge guide enough. The second revealed that the design of the edge guide provided very little support at the end of a board, because of the cut-out for the router bit. In the "Getting Started in Woodworking" video, they had screwed a piece of hardwood to the edge-guide, to provide a continuous -- and longer -- bearing surface. I may do that myself, some day, but I didn't have the materials at hand, so I clamped some 2x4 scrap to the end of each board, to provide a continuous bearing surface past the ends. The two grooves in the long stretchers and the side groove in the short stretchers have identical layout. I made practice cuts in scrap until I had the edge guide set correctly, then I cut them all with that one setting. The bottom groove of the short stretchers uses a different setup, so it was back to the scrap, before cutting them.
Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.
Happy bench building folks. I hope you make it your own and not worry too much about what someone else thinks it should be. Use the rules as a guideline, they have validity, but make it your own in the end. If the rules fit you that’s great, if they don’t quite fit you then make it to fit yourself. It’s you using it, not some guy making a nice living off of telling you how he thinks you should do it. One size does not fit all. Never has, never will.
My name is Takami Kawai and I'm a traditional Japanese carpenter and architect with over 16 years of experience in sustainable design and construction. As much as conditions allow, I enjoy using traditional Japanese techniques. My experience includes working for the world renown, Ise Jingu Grand Shrine. I have also hosted numerous presentations on traditional Japanese woodworking. Now, I run a small construction firm, Suikoushya, which specializes in the restoration of traditional Japanese houses.
This instructable shows how to build, with basic tools and readily-available lumber, a bench that provides most of the function of a traditional woodworker's workbench. I began with a design by Asa Christiana that was featured in the second season of finewoodworking.com's video series Getting Started in Woodworking. The project plans are available on their website.
There are a number of tricks to using a router. First, the bit spins in a clockwise direction, as you look down at the router from the top. This means that when you cut with the router from left to right, the bit will tend to pull the router away from you, and when you route from right to left, the router will pull towards you. So, if you're hooking the edge guide along the near side of the board, route from left to right, and when you're hooking it along the far side of the board, route from right to left. Second, always test the position of your bit on scrap material. Your odds of getting it exactly right by eye are nil. Third, don't cut more than 1/4" deep on a single pass. We want a 3/8" deep grove, so make your first pass at 3/16", or thereabouts, and make a second pass to reach the full depth.
Traditionally woodworkers (joiners) learnt their craft working as an apprentice in the Master Craftsman's shop doing the grunt work and learning by assimilation over many years. Our approach is a little different. We're making the assumption that you're smart; are developing or already have a passion for woodworking; and can devote three months to intensive learning.
For most of the course, we'll be heavily focused on developing your skills using hand tools. As a developing woodworker, there is no substitute for putting in the hours of direct hands on practice it takes to gain an intuitive understanding of wood. The early part of this course focuses on working with hand tools as we believe they bring you closer to wood as a material. You can rip a board on a table saw with out much thought to the wood itself, but you will understand much more about grain if you rip a board with a hand saw. As the course progresses, machine processes are introduced as a pragmatic aid in expediting projects.
The tutorial that I am sharing here was written by someone who built this pallet art just to improve the value of a property they wanted to sell fast and they succeed in it. So you can imagine how wonderful this item must look like. I am assuming you do not just want to make this beautiful pallet art so that you can also sell your property easily. Well, whatever your reasons are, this beauty is able to attract anyone who visits your house.
A couple nice qualities about this bench include the weight and vice capacities. The weight capacity of this bench is 330 pounds which is decent, though it will not wow you too much. The vice, on the other hand, provides a 7” capacity which is tied for the most on our list. That said, there is only a single vice, and it is not able to be repositioned. This can make things a bit frustrating for lefties as it is a right-handed configuration.
I wanted the left edge of the jaw of the front vise to be flush with the left edge of the top, the right edge with the left edge of the left front leg. So the amount of overhang on the left depends upon the width of the front vise jaw. The width of the jaw is, at a minimum, the width of the plate that supports it, but it's normal to make the jaw extend a bit beyond the plate. How far? The more it extends, the deeper a bite you can take with the edge of the vise, when, for example, you are clamping the side of a board being held vertically. But the more it extends, the less support it has. I decided to extend by 1-12", which gives me a 2-1/2" bite, and which should still provide solid support, given that the jaw is 1-1/2" thick. This means the top needs a left overhang of 12-1/4".
The Handy Home Products Berkley 10 ft. x The Handy Home Products Berkley 10 ft. x 10 ft. Wood Storage Building Kit is made with factory-primed SmartSide siding to resist fungal decay and wood-destroying insects. The Berkley’s gambrel style roof provides plenty of height to add a loft for extra storage space. The 6 ft. high side walls ... More + Product Details Close
Learn to use hand and power tools to shape wood into objects that will last for decades. You’ll learn about the properties of lumber, safe tool use, measurement and layout, and fundamental woodworking joints. At the end of this week-long course, you’ll leave with an end-grain cutting board, a mitered corner box, and the skills to build an unlimited range of wooden objects.
This is technically a vanity factor, though the ability to store tools and other supplies at quick reach can be a time and energy saver. At the least, you will want a bench that comes with a shelf underneath. This will allow the storage of larger items that can otherwise be difficult to find a place for. Drawers are the other popular storage for benches and can make retrieving tools much easier – just make sure the inside of the drawer is lined with felt or the wood may prematurely dull your tools.
Anyway, I'd like to know if I'll be able to keep (EDIT: and use) all my tools out there (current and planned) without having the shed become a rust-bucket for the tools and machinery inside. I'll have a 10" contractor's saw out there along with a drill press, a sanding belt, a router & router table, and lots and lots of old tools that I inherited from my Granddad years ago. I live in the Seattle area, so it rains A LOT. But I'm hoping that with the proper ventilation I can keep the tools in the shed dry.