Some tools required for this project are hole saw, drilling machine, pencil, tape measure, clamps, etc. This tutorial explains every step properly with images so that anyone can make a wooden sofa sleeve easily. Those, who prefer a video tutorial, can visit the below link to a YouTube video that illustrates the process of building a DIY Sofa Sleeve Cupholder.
2 - use a plunge router with a bottom bearing cuter bit such as this from rockler: http://www.rockler.com/product.cfm?page=25160&site=ROCKLER .... I thought to use the short one as I plunge it directly downward in the centre of the hole until the bearing reaches within the tabletop hole. I suppose one could use a long one, but the stubbiness seemed more practical (the big bearing ensured accuracy?)
I agree that I might quickly outgrow a 12x8 shed. Lowes also offers a 12x10 Rancher (same style, but more room), but the 12x10 is 9 feet, 4 inches high, and my community only allows a maximum height of 9 feet. The 12x8 is exactly 9 feet high. I'm afraid of getting "out of spec" if I exceed the height limit and then getting in trouble with the Home Owner's Association. Having said that, 12x10 would be about the biggest size I could get for the available area in my back yard, so even if I hire a shed contractor to do this, the shed would have to be 12x10 or smaller.
I made a template by scribing two adjoining squares on a piece of MDF, using compass and straightedge, then marking each corner with a centerpunch, then drilling the points with a 1/16" bit. I find I'm always breaking small bits, so I picked up a couple of each size some months ago, and on looking I found I had three 1/16" bits, which worked fine for what I intended.

Then I flipped the top and the base, lied up the base in the proper location relative to the top, I then positioned the front vise and the support MDF for the end vise, and marked the locations of the bolt holes. Then I flipped the base right side up, drilled small pilot holes from the bottom side where I had marked the locations, and then drilled shallow countersink holes from each side, then a through hole that matched the bolts. Finally I tried out the bolts and washers, and deepened the countersinks until the heads of the bolts were just below flush.
The Handy Home Products Berkley 10 ft. x The Handy Home Products Berkley 10 ft. x 10 ft. Wood Storage Building Kit with Floor is made with factory-primed SmartSide siding to resist fungal decay and wood-destroying insects. The Berkley’s gambrel style roof provides plenty of height to add a loft for extra storage space. The 6 ft. high ...  More + Product Details Close
The popular account showcases woodworking in a variety of ways. Many of the things they share are of artworks produced using its techniques—including My Modern Met favorite Gabriel Schama. Other posts highlight its practical applications in the form of furniture or flooring, while videos offer a look into the process and range from educational to oddly satisfying. Whether you’re a fan of woodworking or looking to try it yourself, @wooodworking will both mesmerize and inspire.
Yea I had a friend who went the HD route and in after putting new braces up for the roof and an extra layer of plywood on the floor he gave up the fight and tore it down. We ended up building twice the shed that was 100 times more sturdy for less than he had invested in the first one. I would go any route that is the opposite way of HD or Lowes. Learn from this guy.
The last thing is to semi-permanently attach the bolts for the vises. Given the amount of work necessary to get to the bolt heads, once the top is joined, I had intended to tighten them up so they wouldn't spin, and lock them that way with blue Loctite. (That's the strongest non-permanent grade.) That didn't work. What I found was that the bottoms of the countersinks weren't quite flat, and when I tightened the nuts down that far, the ends of the bolts would be pulled far enough out of alignment that the vise bases would no longer fit. In order for the vises to fit over the bolts, I had to leave the nuts loose enough that the bolts had a bit of wiggle - which meant that they were almost loose enough for the bolts to spin. So I put Loctite on the nuts, to keep them from unscrewing, and filled the countersinks with Liquid Nails, in hopes of keeping the bolts from spinning. I considered using epoxy, or a metal-epoxy mix like JB Weld, but I didn't have enough of either on hand. It seems to be working for now, though the real test won't be until I have to take the vises off.
In this two day class we will reveal some of the secrets to tuning up a Japanese Hand Plane (Kanna) We will start with conditioning the Body of the Plane (DAI) to stabilize movement. Proper sharpening and grinding of the blade and chip breaker will be discussed and demonstrated. Custom fitting the blade to the Dai and conditioning the sole. We will...
Cerritos College Woodworking, one of the finest woodworking schools in Southern California, offers classes in furniture making, cabinetmaking, CNC woodworking, and related topics.  Cerritos is the school for you, whether your goal is to acquire new knowledge, gain confidence in or improve your skills, enter the field of professional woodworking, or develop a rewarding hobby.

Students will make two pens at the lathe, one of solid wood and one of your own design built up from several pieces of wood. Since turning pens is a quick process, we will have time to teach you how to choose woods, how to prepare and mount wood on the lathe, and several of the more popular finishes. We will cover safe operation of a lathe, demonstrate how to use common woodworking tools, practice tool sharpening techniques, and discuss options for what kind of lathe you might want in the future, from a small pen lathe to more robust machines that can handle much bigger projects. Bring clothes that can get dirty.
We are especially proud of Post Woodworking’s Brunswick style shed. It has all the rugged features and simple, beautiful mystique of a Maine coastline. Natural-wood siding options, in pine or cedar, offer a rustic aesthetic. Or, choose a vinyl color that complements our home. Once inside the Brunswick, its unique, two-sided sloped roof maximizes headroom, making space for you to better maneuver a rake. Black architectural hinges and hardware lend distinguished contrast and quality to this basic but appealing storage solution.
×