My advice? Don't do this. If you have jointer and a planer, use them. If you don't, seriously consider using dimensional lumber that has already been planed and sanded. If you are going to try to clean up construction lumber by hand, using a hand plane is a lot faster and more pleasant than using a belt sander. Except, of course, that to do a good job of planing a board you need a solid bench to hold the board, and you don't have a bench, yet.
Put the countertop on the base, put the MDF on top of the countertop, and line up the marks you drew on each end of the MDF with the countertop below it. When you have it lined up, clamp things down, and route the edge of the MDF using a 1-1/2" or longer flush-trim bit, with the depth adjusted so the bearing rides on the countertop. I clamped a couple of scraps of doubled MDF at each end to give the router base something extra to ride on at the ends.
In this class we will explore the works of one of my favorite woodworkers, George Nakashima. This chair has elegance, simplicity, subtle details, and beauty. Don’t let its simplicity fool you. This chair requires great skill and precision to execute. It involves carving and sculpting of the seat with power and hand tools. The complex joinery has...

If you decide upon construction lumber, you want kiln dry lumber. Green lumber will warp on you as it drys. Dig through the stacks and pick out the straightest, cleanest pieces. Generally, the boards that are sitting loose on the stack are those that other people left behind, as they sorted through looking for better. Be prepared to move them out of the way, and to dig down to the better stock. Be nice, though, and put everything back when you're done.
A steam box and a heat source are the two main components used to steam bend wood. Steam boxes must be able to withstand large fluctuations in temperature and humidity without breaking apart. In this two-hour workshop, students will build an optimized steam box that can last through the tough job of steaming wood, allowing them to continue creating their own projects at home!
Well, not these plans. You have the option of building a very functional and spacious lean-to shed on different foundations. Your foundation choices are: concrete slab, a wooden floor supported by concrete piers, or a wooden floor supported by skids. That lost option also means that your lean-to could be mobile as well so you won’t have to decide where you want to permanently put it.

I live in VA and my workshop is an unheated, uninsulated garage. I work out there year round, even when temps are below freezing. I can't say it's comfortable in the winter (or when it's 100 degrees with 95% humidity) but I haven't had any major issues. I have had some big box green wood warp on me after I built a couple bookshelves and brought them into the house, but that was more a factor of the green wood than my "shop".

Sjobergs’ woodworking benches are recognized all over the world for their durability, handy design and extra features that make these benches well worth the money. This Hobby Plus bench is the perfect fit for a woodworking enthusiast, especially since it is equipped with two vices and bench dogs. This could become your one and only woodworking station!


Next is the shelf. Start with the 24x48" piece of MDF. Clamp this on top of the base, and pencil in the outside of the stretchers and the inside angle of the legs. Flip it over, pull out your trusty cutting guide, and cut it to width and to length. Cutting out the angles is simple, with a jig saw. It's not much work with a hand saw. If you took enough care with supporting blocks and stops, you could probably do it with a circular saw. Since I did have a jig saw, I used it.
Right now, there is a revolution in woodworking courses created by the closure of many state-run colleges. Our workshop has led the way and been the model for many of the private furniture making courses available to you today. Rowden Atelier is recognised as a Centre of Woodworking Excellence that produces exceptional furniture and trains exceptional woodworkers. With our range of specialist woodworking courses, you could be one of them.
The Practical Woodworking course at the JD Lohr School of Woodworking is a complete and comprehensive woodworking course held in our shop on the 13-acre farm in southeastern PA. This is total immersion woodworking for ambitious, interested adults. With class size limited to 11 students and 3-4 instructors in each class, all needs of every student are met regardless of experience level. If you are self taught with no formal training as a woodworker, this course will quite literally change the way you work.
Can you believe that this amazing wine rack the image below has been built using old wood pallets? Perhaps you can. Isn’t it wonderful that your old wood pallets can be reused to build something so beautiful and useful? I am not a drinker but I liked the idea so much that I just couldn’t resist making myself one. Although later I gifted it to my parents, who totally loved it.

We have more than sixty years of excellence (1956-present) with an annual enrollment of more than 1,000 students in over 35 different classes.  The Palomar College Cabinet and Furniture Technology program offers the most comprehensive woodworking career curriculum in the nation. Utilizing three fully-equipped shops, our 2 full-time and 20 part-time instructors provide a breadth of courses and depth of expertise impossible to obtain in smaller programs.
If you decide upon construction lumber, you want kiln dry lumber. Green lumber will warp on you as it drys. Dig through the stacks and pick out the straightest, cleanest pieces. Generally, the boards that are sitting loose on the stack are those that other people left behind, as they sorted through looking for better. Be prepared to move them out of the way, and to dig down to the better stock. Be nice, though, and put everything back when you're done.

I marked out the one hole location, drilled a shallow 1/16" hole into the top. I then put a 1/16" bit through the hole in my template and into the hole I had just drilled. I lined up the template, and drilled a second hole, then put another bit through that. From then on, I worked entirely from the template. With two bits through the holes pinning the template in place, the other holes in the template would be precisely located (or so the theory goes) on a 4x4" grid.
I decided to finish the top with a number of coats of Danish oil, followed by a coat of wax. I applied the first coat of oil in the usual manner, making sure to cover the edges, and down the holes. I applied a coat oil to the top side of the shelf, as well. Wipe it on, let it sit wet for half-an-hour, then rub it off. Wait a day or two, add a second coat, and then again for a third.
Lay a leg flat on your work surface, with the countersink side of the thru-holes down. Stick a piece of threaded rod in each hole. Take a stretcher that is marked to have one end adjoin the top of this leg, stick a dowel center in its dowel hole, line it up against the leg, using the threaded rod for positioning, You want the top of the stretcher to be even with the top of the leg, or just slightly above it. Give the end of the stretcher a whack with your rubber mallet. This will leave a mark indicating where the matching dowel hole in the leg needs to be drilled. Repeat with the lower stretcher than adjoins this leg. Then repeat for the other leg that will form this trestle, and the other ends of the two stretchers.
Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.
The beauty of this project lies in the simplicity. All you need are 3 pieces of wood of your choice (though we must admit natural hardwoods will look incredible), sanding block, clamps, wood glue and finishing product. The hardest step of the whole tutorial is measuring – as always, measure 9 times, cut once! You wouldn’t want to finish your project and then realize it doesn’t have enough space to fit your DVD player, would you?
The front edge of a woodworker’s bench is usually lined with square holes positioned at regular intervals. These holes hold bench dogs and holdfast clamps in place for securing work pieces. Beneath the top of the bench, some cabinetmaker models feature single storage drawers, others several drawers and even cupboards incorporated into a case-like base.
When you have the other leg seated, the threaded rods will extend father than you want them to. You'll want to mark them so they can be cut to length. Place a washer and a nut on each threaded rod, and then tighten down the nut to pull everything tight. Depending upon the wrench you are using, and how much longer the rod is than it needs to be, you may find it necessary to stack up a number of washers, so that the nut is positioned where the wrench can operate on it.

I don't like to be ignored either. I came the same day Mahndo left after waiting 30-45 mins. I left a note with name and number but no one even called me back. I was completely ignored. I found a class over at The Corona Heritage Park in Corona instead. Their instructor answers when I call or text. Nice to be acknowledged! Going to finish beginning and take advantage of the key access in their intermediate class.
Then I flipped the top and the base, lied up the base in the proper location relative to the top, I then positioned the front vise and the support MDF for the end vise, and marked the locations of the bolt holes. Then I flipped the base right side up, drilled small pilot holes from the bottom side where I had marked the locations, and then drilled shallow countersink holes from each side, then a through hole that matched the bolts. Finally I tried out the bolts and washers, and deepened the countersinks until the heads of the bolts were just below flush.
The reason I'd cut out the rectangles in the vise support was that I'd intended to put a benchdog hole through each, and I wanted the thickness of the top to be the same for all of the benchdog holes. Where I messed up was in not cutting out the ends, between the bolt tabs. I'd intended to put a benchdog hole through there, as well, but I'd forgotten to cut out the segments prior to glue0up.
If you don't quite have the space for a real pony, make this handcrafted wood version instead. The horse pictured here is unfinished pine, but there are lots of woods and finishes to choose from. Everything you need comes with the kit, and the plans can be downloaded. If you don't want to build it yourself, you can order from the website—just allow two to three weeks to ship.
Right now, there is a revolution in woodworking courses created by the closure of many state-run colleges. Our workshop has led the way and been the model for many of the private furniture making courses available to you today. Rowden Atelier is recognised as a Centre of Woodworking Excellence that produces exceptional furniture and trains exceptional woodworkers. With our range of specialist woodworking courses, you could be one of them.
For the router you'll need a a 3/8" straight bit, an edge guide, 1/4"- and 1/8"-radius roundover bits, and a flush-trim bit with at least a 1-1/2" cutting length. Bits of this size are available only for a 1/2" collet. Some routers are capable of using multiple collet sizes. I was fool enough to buy a router that only had a 1/4" collet. More on that, later.
This is another example of small woodwork projects that require good time and woodworking skills. This item is built using multiple wooden parts. Each part is shaped in a specific design and then all parts are attached together to make the final TV set. I have never tried building this one, mostly because I don’t own an iPhone, but also because making this item is not an easy task. By the way, it works fine with all kinds of phones.

Learn how to use power tools, as well as traditional and modern hand tools, safely and effectively. Class assignments introduce basic concepts and techniques, to give you the skills needed for many woodworking projects such as mill board flattening and straightening, creating strong joints for connecting wood, and gluing boards together to make a panel. Students leave with a strong foundation for more advanced wood classes and a small end table. All tools for learning are provided.
Timberframing is a traditional technique for building large and small structures using only wooden joinery. Prized for its structural integrity and beauty, as well as reliance on hand skills, timberframing is regaining popularity in modern applications. We will start with an overview of the different styles and aesthetics involved, and move into the specific tools that are used to lay out and cut the strong joints. Each student gets guided practice time making sample joints. We will all work together to make a small structure that can be raised on the final day of class.
First, we need to drill out the holes for the screws that will hold them together. While the two layers of MDF are glued, the countertop and the MDF will only be screwed. The oak countertop, like any natural wood product, will expand and contract with humidity changes. If it were glued to the MDF, the difference in expansion of the two layers would cause the countertop to buckle and curl.
A better solution would have been to route a rabbet into the side, so that the added strip always had thickness. The way I did it means that the strip I glued in is very narrow, and hence very weak, at a certain point. In this case, that's not a problem, because it's going to be sitting under the countertop layer. I also noticed that because I had only clamped the strip down, and not into the edge, there was a noticeable glue gap where the strip butted up against the MDF. Again, in this application it isn't visible. But if I was doing something like this on the top of a table, I'd make sure to cut a clean rabbet, and to clamp both down and in.
One aspect of the Windsor Design that is hit or miss is the vice. Notice we have to use the singular when describing it because this is the first workbench that we have reviewed which features only one vice. To make matters more frustrating, the vice cannot be repositioned along the bench. That said, the vice does at least have the largest capacity out of any we reviewed. At 7” capacity, the Windsor Design vice can secure any size workpiece you may have.
The remaining tuition payment ($7,000.00) and materials deposit ($300.00) is due 45 days before the start date. Any unused materials deposit will be returned at the end of the course. You may use the materials deposit to buy books, finish, wood, fasteners, and hardware. Due to credit card processing fees, we kindly ask that students make this portion of the tuition payments by personal check, money order, or bank check.
In terms of size, this bench is another Sjobergs that is a bit on the small side, though it is actually far more squared than some others. While its length is a bit disappointing at 54″, the width is over 24″ wide which does provide for more diverse projects. Even better, this product still features the incredibly 500-pound weight capacity and continues the Sjobergs trend of avoiding joints that are not as durable as they otherwise could be.
Linseed oil sitting in a bowl, or spread on the surface of wood, is perfectly safe. But a linseed oil soaked rag provides a vastly increase surface area, so the oxidation happens faster, and the rag can provide insulation, trapping the heat. The increased temperature speeds up the oxidation even more, which raises the temperature even more, and the runaway feedback can quickly result in temperatures that will cause the rag to spontaneously burst into flame. This isn't one of those "do not drive car while sunscreen is in place" warnings. This is one of those "keep your finger off the trigger until you have the gun pointed at something you want to shoot" warnings. Rags soaked in linseed oil will catch fire, if you don't handle them properly, and they can do so far more quickly than you might think.
I live in the second rainiest city in the country, Pensacola, so I am used to dealing with wet. I literally work out of my garage (read storage area, small woodwork area, washer/dryer...car? ). I wheel bigger tools and table out to the little covered area in front of the garage. I have an 8 x 10 aluminum shed that is strictly garden stuff storage. I mention this for two reasons.
×