In 2006 Jonathan Schwennesen had an opportunity to begin an informal apprenticeship at the age of 17. He spent 4 years working as an apprentice in the Heritage School of Woodworking, learning the fundamental skills needed to build custom and speculative pieces of furniture. Next he began working for Homestead Heritage Furniture building custom furniture for different clients, gaining additional experience and knowledge making Windsor chairs, federal-style cabinets, clocks, workbenches, sleigh beds and even a waterwheel! It was during this time that he began to show an interest in teaching. Jonathan became a teacher’s assistant in 2009. He quickly began gaining the knowledge and skill to teach some classes himself. Now he spends most of his time working for the woodworking school. “My desire is to teach others an important aspect of life: working with your hands.”
Can't say enough about the team at Post Woodworking, Inc., from Karen in the office to the team that... put up this beauty starting at 7AM and were done before lunch, Kyle, Aaron and Billy. After what sounded like a late night at the shop the night prior, they were still on site bright and early as promised and still energized and ready to show their pride in their work. Couldn't be more happy with our 14' x 20' Cohasset. See More
The top is supported by the top ends of the legs and the top sides of the top stretchers. Stand your legs on end on a flat surface (like my door) and see if they wobble. If you have an end that isn't quite stable, use it as a foot, where the leveler will make it's flaws unimportant. Check the top edge of each stretcher for straightness. If one has a bit of a bow, use it for a lower stretcher. It's less critical that the shelf be well supported along its length.

I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.


Having done all this, I'm not sure I'd do it this way again. It might well be faster to layout the positions with compass and straightedge directly onto the top. Either way, you'll want to use a scribe rather than a pencil. Scribe lines are hard to see, and impossible to photograph, but the scribe and compass points click into them, allowing a precision that pencils simply cannot match.
The projects in this course follow a natural progression of skills, techniques and tools. Some of the early student-made tools are, in fact, used to help make the next tool or bench fixture in the series. You are supported in the building of these projects with step-by-step outlines, knock-down examples and continuing, one-on-one consultations with the faculty. Periodic evaluations of your progress with a specific faculty-mentor help keep you on track.

Even with all of those faults my only regret is that it is too ugly. I didn’t take the time to make it more visually attractive as I was eager to get right into making beautiful furniture instead. Twenty years later the furniture is still beautiful (or not) but I go out to the shop and look at a drab uninspiring workplace. Yeah, nothing wrong with having a visually inspiring workplace in my opinion. All that shop furniture I slapped together years ago with no concern about aesthetics is getting replaced bit by bit. Why should my shop be downright ugly when it is one of my favorite places in the world to spend my time? I see no reason for that, but that’s just my opinion and as we all know everyone has their own one of those… Sadly, no one pays nor reveres me when I offer mine. bummer, I could be a rich egotistical maniac if they did coz I sure offer it enough. 😉
PS:  I saw that a recent review from Nicholas L. hinted that some people weren't welcome at the Community Woodshop. I can say with absolute certainty that everyone I've met has been welcomed with open arms and encouraged to participate at the woodshop. My class is a mix of genders and races, and nobody has experienced any difference in treatment from Bob or anyone else there. I truly can't imagine a situation where anyone would be treated any differently.
Evidence of a removed fireplace makes it clear that the woodworkers were doing tasks that required warmth, like using glue. The type of glue used during that time had to be heated to a certain temperature. Bill Flynt, a former colleague of Garrison, tested the wood of the shop and found that it is second- or third-generation wood, meaning that New Englanders had already cut down and replanted lots of trees by that time.
As simple as its elements are, the workbench is more than a tabletop with legs, a well, and a few holes. Virtually everything in the workshop comes to rest on the bench at some point, even if only between operations at other stations. Planning and layout, cutting and shaping, assembling and finishing–all can be, and often are, performed on the benchtop. The better the design, and the better suited its size and configuration to your labors, the more efficient a tool it will be.
Another wooden item that I love very much is a beautiful mobile holder. You can see one in the image below. These things are not only beautiful, but they can comfortably hold any sized mobile and ensure proper safety. Another amazing thing is that they can be built in many shapes and sizes, as and how you need it. You can see some more examples at the source below
For the router you'll need a a 3/8" straight bit, an edge guide, 1/4"- and 1/8"-radius roundover bits, and a flush-trim bit with at least a 1-1/2" cutting length. Bits of this size are available only for a 1/2" collet. Some routers are capable of using multiple collet sizes. I was fool enough to buy a router that only had a 1/4" collet. More on that, later.
This is definitely going to be one of the easiest woodworking projects you’ll be reading about today. So why not just get started? The tutorial link is given below. Just do exactly what they are saying in the tutorial and you will end up making a beautiful wooden doormat just like the one in the image above. They are using pine wood to build this doormat. You can choose any wood material that best suits your budget.
So far, I really like the space. I signed up for a 3 month stint and hopefully will have some things to show for it. For my background, I took shop for 3 years in high school. I've always enjoyed working with wood but never had the space for it. I'm not a master craftsman but there are some really talented people there creating some nice pieces. All levels are welcome here.
Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.
The right shed for your home will depend on your desired use. Utility bins are ideal for storing trashcans and recycling bins out of sight. Patriot sheds are ideal for sporting equipment, riding mowers, snowblowers, and other small vehicles and heavy tools. If you want a workshop with storage to spare, look into the Elite line of products. With creative small-space storage solutions, any one of our sheds can truly increase the usable space in your home.
The oldest woodworking shop in America has been discovered virtually untouched in Duxbury, Massachusetts. The extremely rare find reveals an 18th century joiner’s shop with the date ‘1789’ painted in the rafters. University of Delaware professor Ritchie Garrison came upon the historic structure on the site of a preschool, bringing several experts out to verify its age. Craftsmen used the shed to create intricate woodwork.
Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.
The course successfully meets the needs of multiple experience levels in a safe, well equipped, spacious, congenial, and educational environment. All instruction and lab experience is under the personal direction of master woodworkers as well as one or two additional experienced woodworkers/teacher assistants who are on hand during all lab hours providing roughly a three-to-one student-to-instructor ratio. Intermediate to more advanced students should not be put off by the fact that beginners are also included in this course.  Check out some of the work done by our alumni in the Alumni Furniture Gallery to get an idea of what our students are capable of.
If you remember, when drilling the MDF I finished the holes from the other side using a Forstner bit. It made for a clean hole, but the positioning wasn't as precise as I really wanted. So for this, I decided to clamp a length of scrap MDF to the back side, and to drill straight through. My Forstner bits were too short, so I bought an extender. And then I found that the spade bits I was using gave a cleaner exit hole. Whooda thunk?
Then I flipped the top and the base, lied up the base in the proper location relative to the top, I then positioned the front vise and the support MDF for the end vise, and marked the locations of the bolt holes. Then I flipped the base right side up, drilled small pilot holes from the bottom side where I had marked the locations, and then drilled shallow countersink holes from each side, then a through hole that matched the bolts. Finally I tried out the bolts and washers, and deepened the countersinks until the heads of the bolts were just below flush.
The end vise will have both jaws made out of 1-1/2" thick oak. The front vise has its moving jaw made of 1-1/2" oak, but uses the edge of the bench as its stationary jaw. So while for the end vise, if we mount it lower, we can make both the jaws deeper to compensate, for the front vise we cannot, so we want it mounted as close to the edge of the bench as possible.

Dip your toes in the world of woodworking with our week-long courses, and by the end of the week, you'll be swimming. During these intensive, week-long woodworking courses, you will benefit from the guidance of our expert furniture makers, learning the basic principles of woodwork and cabinet making to professional standards. Hone your technique with our classes and create precise, beautiful work with our expertise, equipment and advice at your disposal.

Practical Woodworking is a 50 hour comprehensive course that focuses on the necessary skills, tools, techniques, and safety to successfully enter the world of woodworking and furniture making. Beginner, intermediate, and advanced students learn about furniture design, construction, and finishing as well as wood behavior, hand tools, machines, milling from the rough, squaring, and joinery. It  is an intensive class for folks who want to continue woodworking in the future. It is a week of hard work with a lot of fun mixed in. Watch the video and read below for a more in-depth look at what we're all about.


I agree that even at 12x12, things'll be "cozy" inside. That's OK. Keep in mind that this will be a general purpose hobby shed, not just a wood working shed. Even 12x8 would be plenty big enough for building 1 meter wingspan bungee launched RC gliders. And for the electronics projects I do, I only need enough workbench space to do some soldering with a 3rd hand (for electric guitar pedals). If I need more room than the shed offers for wood working projects, I'll just roll the table saw down a ramp and do my cutting outside in the sun.
×