The edges of MDF are fragile, easily crushed or torn. MDF is also notorious for absorbing water through these edges, causing the panels to swell. In Sam Allen's original design, he edged the MDF with 1/4" hardboard. This edging is one of the complexities that Asa Christiana left out in his simplified design. I think this was a mistake. MDF really needs some sort of protection, especially on the edges.
I wanted the left edge of the jaw of the front vise to be flush with the left edge of the top, the right edge with the left edge of the left front leg. So the amount of overhang on the left depends upon the width of the front vise jaw. The width of the jaw is, at a minimum, the width of the plate that supports it, but it's normal to make the jaw extend a bit beyond the plate. How far? The more it extends, the deeper a bite you can take with the edge of the vise, when, for example, you are clamping the side of a board being held vertically. But the more it extends, the less support it has. I decided to extend by 1-12", which gives me a 2-1/2" bite, and which should still provide solid support, given that the jaw is 1-1/2" thick. This means the top needs a left overhang of 12-1/4".
I'm not kidding when I say that this shop has everything you need to make a project happen.  They are not only equipped but also some of the nicest people.  Supportive and, mostly, willing to help you with your project.  The idea is for you to do it on your own, but if you get stuck I have yet to see someone say, "no, figure it out on your own."  they are helpful and fair.  I love this place, and the people I have met there.
Cerritos College in Norwalk serves over 21,000 credit students each year with certificate and degree programs for recent high school graduates and adult learners. The Cerritos College Woodworking school is housed in 27,000 square-feet of space and is equipped with over 100 woodworking machines. Under the direction of 20 instructors, the school offers more than 50 classes in woodworking, including those in architectural millwork, cabinet and furniture making, routing and veneering.
The bench would end up being about 5 feet long. I thought about cutting 5 feet out of my 8 feet long countertop and use the rest for a small support table. However, after a consideration, I decided to bypass the front vise altogether together with the overhang so my bench will be 4 feet long. This allows me to skip the MDF and just glue the two halves of the 8 feet board together.
Our programs prepare our students to open their own woodworking business or become employed by a high-end woodworking related business. We currently offer an Associate of Science Degree as well as a Certificate of Achievement in 8 different Program Areas. Students may also take coursework to complete a Certificate. Our courses range from Furniture Design and Instrument Making to Production Cabinetmaking.   Our graduates are highly employable with the diversity of courses available.
Thinking about transitioning into serious woodworking, but don't have half a year or more to spare? Our one-month fine woodworking courses are perfect for those who are looking to move towards professional woodwork, but can’t find the time to commit to a longer course. Here, our woodworking classes will intricately teach you all of the basics, the same as you would for our three, six and twelve-month courses, with projects specially-created for both beginners and the more experienced. This will truly bring your woodworking skills up to the high level of craftsmanship needed within the industry.
Build a shed yourself and use it as "on the job training." Those straw built sheds are rinky dink. The people who throw them together are even more sketchy than the finished product. You will be tearing it apart and hauling it out within a few years. Or end up having to reinforce the building with more braces and another layer of flooring. Thats my 99 cents. Its not hard to build a shed especially one of that size. Cowboy up and give it a shot.
This is not exactly a tutorial, but a guide to some really cool woodworking projects. Although we are not teaching you to make anything, we are always here to help. Feel free to ask your queries in the comments in case if you face any issue while working on any of these projects. Also, tell us how much you liked this article. Did you enjoy reading it? Did you work on any of these projects, and if yes, how was your experience? You are also welcome to share any images of your completed woodwork projects.
I built my first platform bed by following the steps mentioned in the tutorial and the end result was everything I expected. It was as beautiful as comfortable and strong. It only cost me around $60 to build this one from the scratch. And if I can build it, anyone can. What you need is a little bit of woodworking experience and a lot of confidence. Collect the items as suggested in the video and start working now.
The Classic Workbench is simple to use. The leg vise is used primarily for working the edges of boards and the ends of narrower boards. This is self explanatory. To work the faces of boards along the grain, tap up the planing stop (don’t make it any higher than necessary) and butt the end of the board into the teeth of the stop. With the right technique you can plane across wide boards without repositioning the board. You usually don’t need to tap the opposite end of the board to engage it with the stop, but in some cases, especially with rougher stock, you may need to give a tap with your mallet. Working the faces of a stack of boards is extremely quick with the planing stop since you don’t have to open and close a vise constantly. To work across the face of a board, make yourself a doe’s foot and position it at the back corner of the board, holding it down with a holdfast. The doe’s foot is simply a piece of wood with a V-shaped notch cut into one end. The bottomsurface of the doe’s foot can be lined with sandpaper or Crubber to help it stay put on the bench top. To work long boards, fasten a batten to the right leg with a holdfast and use that to support the end of the long board. We’ve found that a deadman is not necessary for the majority of work, especially on a bench of this length. For working the ends of smaller boards the leg vise can be used, but for precision work like dovetailing, we use and recommend our Moxon Vise.

I ended up making a number of practice cuts. The first revealed that I hadn't tightened the screws on the edge guide enough. The second revealed that the design of the edge guide provided very little support at the end of a board, because of the cut-out for the router bit. In the "Getting Started in Woodworking" video, they had screwed a piece of hardwood to the edge-guide, to provide a continuous -- and longer -- bearing surface. I may do that myself, some day, but I didn't have the materials at hand, so I clamped some 2x4 scrap to the end of each board, to provide a continuous bearing surface past the ends. The two grooves in the long stretchers and the side groove in the short stretchers have identical layout. I made practice cuts in scrap until I had the edge guide set correctly, then I cut them all with that one setting. The bottom groove of the short stretchers uses a different setup, so it was back to the scrap, before cutting them.


1. In this post, you kindly remind us not to make it too deep or worry too much about the height. I presume you still believe a bench cannot be too long or too heavy? I’m with you — just asking if that’s actually still your opinion, since the bench above appears to be yet another six footer. (If longer is better, why don’t you build an 8 or 10′ for your home shop?) TYIA – remember, I’ve bought all my lumber to start my new bench, but I haven’t milled anything yet, so you’re really helping in an immediate way here!
We're planning to have a tree cutting service come in and take out a couple of diseased trees in the back part of our lot and then hire someone else to dig out the stumps. These trees are at the base of a small rise, and we're thinking about cutting into the "hill" a little bit and making a low retaining wall, maybe 18" to 24" high. But that's just intended to move the shed back a bit from the house. (Our total lot size is only 5,616 feet with an 1,800 square foot house.) Landscaping change like this won't affect current drainage patters, but anything else might make it worse.
×