If the holes of the first jaw are in the proper position, drill holes in the same locations on the other jaw. I lined the drilled jaw on top of the undrilled jaw, clamped things down, and then drilled about 1/4" into the undrilled jaw, to mark the location. Then I removed the drilled jaw and drilled out the marked locations the same way I did the first.
I'd decided on an oil-and-wax finish. Oil finishes are by no means the toughest. In fact, they're really rather pathetic, so far as protecting the wood goes. But they're easy to apply, and not even the toughest finish will stand up to the abuse that a workbench will suffer, so it's more important that it be easy to repair. Wax is usually used to add a high gloss. On a bench, it's there to keep glue from sticking.

You are absolutely right on your advise. When I was agonizing over how to build a workbench my good friend turned me on to your book on workbenches. I was planning on having an overhang until I read your advise about building a workbench and not a table. So the entire front and rear surfaces; top, legs and bottom shelf are all in the same plane to clamp my work to. The addition of a sliding dead man was also something that I would have never thought of on my own. Thanks again for your advise.
While a strict figure for the bench’s weight capacity is not available, a quick browse through their other stand and bench products shows a general weight capacity well above most other brands. As such, while we cannot say for certain that this bench provides the best weight capacity, it is more than likely that it the capacity is similar to the other products in the catalog.

In this class, John will explain and demonstrate safe spindle turning techniques for turning a bud vase or a carvers mallet, an essential tool for anyone wishing to sculpt wood or make hand made joinery. Objective Through hands-on learning students will gain experience and confidence using our new Laguna mini lathes. You will develop an understanding...


I like the idea of re-inventing the wheel. I choose to believe that while others may have considered these improvements, they just never got around to trying them out. Brain gets bored with status quo. So, I try to keep Brain happy with the occasional foray into uncharted territory. And I must say Brain has had some really good results. Thanks, in part, to you, and the Roy. You never know where a good idea might come from so I’ll check in once in a while. That and make sure to build it in Sketchup first.

I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.
The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details. Follow the steps properly to make a nice and strong wall rack. This rack makes use of magnets to hold metal items. The tutorial explains the procedure for building this beautiful wall rack. Make sure to use only high quality items for any woodworking project. Use the rack only to hang items that are not too heavy for the magnet to hold. Also, be careful while working around this wall rack and beware of the knives falling off the rack.
Another odd design feature of the Windsor Design is its dog holes. While this bench provides a variety of dog holes and even offers numerous pegs and dowels to go along with it, the dog holes are not spaced as closely or with as much variation as you see with many other benches. Ultimately, this means that smaller workpieces may not be able to use the dog holes and pegs as well.
Happy bench building folks. I hope you make it your own and not worry too much about what someone else thinks it should be. Use the rules as a guideline, they have validity, but make it your own in the end. If the rules fit you that’s great, if they don’t quite fit you then make it to fit yourself. It’s you using it, not some guy making a nice living off of telling you how he thinks you should do it. One size does not fit all. Never has, never will.
Still in the building mood? Get free woodworking plans to build greenhouses, barns, pergolas, garages, dog houses, potting benches, router tables, playhouses, cabins, tree houses, gazebos, porch swings, picnic tables, swing sets, deer stands, bookcases, home bars, wine racks, decks, work benches, chicken coops, bird houses, benches, and even homes.
2. Did I mention the rain here? How is your shed built? Are flooring and walls sealed to prevent water blowing and leaking in? When we get our summer thunderstorms the winds can whip up the rain pretty good and I even have to make sure garage door is closed sometimes. The shed??? Yea. it gets wet inside no matter how much caulk I use on floor gaps. Mine is on slab and shed not really designed to be waterproof. That being said, even if I got floor sealed it still lets some water in where walls meet roof. Not lots but makes for extreme humidity (or dew point if you prefer) levels.

Though still straightforward in design, this bench distinguishes itself from many of its competitors with the sheer wealth of storage options. It includes two drawers of equal size with an additional drawer of double size as well as a spacious cupboard. Altogether, this provides for more storage space and organization than any other workbench we reviewed. Of course, this bench also comes with many of the same advantages and disadvantages that you would expect to see on other models within this lineup.


Can't say enough about the team at Post Woodworking, Inc., from Karen in the office to the team that... put up this beauty starting at 7AM and were done before lunch, Kyle, Aaron and Billy. After what sounded like a late night at the shop the night prior, they were still on site bright and early as promised and still energized and ready to show their pride in their work. Couldn't be more happy with our 14' x 20' Cohasset. See More
Chris I blame you for all these altars that are being built today and now you thinks we over thinks ’em–huh. You whipped the masses into a frenzy— now Woodworkers are trying to out pretty each other–out wood species each other –out Rube Goldberg each other. I made 2 benches in 30 years neither had a through dovetail but many were made on them and I have no idea but I would bet a dollar that neither weighed 280 pounds but they both had tons of wood on them. If you want the bench as a destination god bless but it was intended as a mean. Thats my rant I could be wrong
The book is well written and easy to read. The illustrations, I'm sure were excellent in 1914 and, are still adequite now. Most of the designs seemed repetitive, though. I wish more attention had been given to lashing materials. If you are looking for that you will find almost none here. The book was fun to read and provided enough inspiration to make my brother and me attempt a large hut.
×