Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.


Another odd design feature of the Windsor Design is its dog holes. While this bench provides a variety of dog holes and even offers numerous pegs and dowels to go along with it, the dog holes are not spaced as closely or with as much variation as you see with many other benches. Ultimately, this means that smaller workpieces may not be able to use the dog holes and pegs as well.
You may even want to put yourself in the picture. If your workshop space already exists, find a large piece of cardboard, wallboard, or plywood that’s about the size of the workbench top you envision. Find a couple of stools or chairs, perhaps a few books, and turn them into stanchions to support the “benchtop.” Is it too big for the space? Is it large enough for the tasks you envision will be performed upon it?

2 - use a plunge router with a bottom bearing cuter bit such as this from rockler: http://www.rockler.com/product.cfm?page=25160&site=ROCKLER .... I thought to use the short one as I plunge it directly downward in the centre of the hole until the bearing reaches within the tabletop hole. I suppose one could use a long one, but the stubbiness seemed more practical (the big bearing ensured accuracy?)


Put the upper panel of MDF on your glue-up surface, bottom side up. Put the bottom panel of MDF on your other surface, bottom side down. (The panel with the holes drilled in it is the bottom panel, and the side that has the your layout diagram on it is the bottom side.) Chuck up in your drill the appropriate driver bit for the screws your using. Make sure you have a freshly-charged battery, and crank the speed down and the torque way down. You don't want to over-tighten the screws, MDF strips easily.
The decision to be made with respect to the end vise is whether the support plate should be mounted to on the inside or on the outside of the stretcher. Mounting the plate on the inside of the stretcher reduces the reach of the vise - it can't open as far, because the support plate is back from the edge by a couple of inches. But mounting the plate on the outside of the stretcher means that we need to add some support structure for the inner jaw of the vise, which the legs would have provided if we'd mounted the plate on the inside.
In this class we will explore the works of one of my favorite woodworkers, George Nakashima. This chair has elegance, simplicity, subtle details, and beauty. Don’t let its simplicity fool you. This chair requires great skill and precision to execute. It involves carving and sculpting of the seat with power and hand tools. The complex joinery has...
So drill the benchdog holes through the MDF layer. Begin by laying out their positions. You'll want these to be precise, so that the distances between the holes are consistent. The vises you are using will constrain your benchdog spacing. My front vise worked most naturally with two rows of holes four inches apart, my end vise with two pairs of rows, with four inches between the rows and eight inches between the pairs. Because of this, I decided on a 4" by 4" pattern.
Whether you're just starting out or wish to upgrade your important hand tools, this 5-Pc. Professional Woodworking Kit with matching rosewood and brass accents has all the essentials for producing the very best work. This fine set includes a 9" smoothing plane, 6" block plane, 9" try square, 9" marking gauge, 9" bevel gauge and a fitted wooden case.
All glue & stain benches are made using a solid maple frame for lasting durability and strength. Side Clamp Benches are made specifically for bar clamps, and are used for gluing projects or clamp storage. Benches feature an open top with 17 sets of 3/4"W grooves that accept bar clamps measuring 3’ and over. Lower center rail is adaptable for storage of hand screws and C-clamps. Side clamp benches are available with or without a drip pan. Glue & Stain Benches are made with a 1-1/4” plywood top covered with heavy-coated galvanized steel. Bottom shelf has a 4” rear retaining lip. Glue and stain benches are available with or without casters. Limited Lifetime Warranty.
Learn how to use power tools, as well as traditional and modern hand tools, safely and effectively. Class assignments introduce basic concepts and techniques, to give you the skills needed for many woodworking projects such as mill board flattening and straightening, creating strong joints for connecting wood, and gluing boards together to make a panel. Students leave with a strong foundation for more advanced wood classes and a small end table. All tools for learning are provided.

Frame making may look simple but it is a skill that escapes many. For a frame to properly do its job it has to be perfect, any mistake can be a distraction that takes away from the artwork it surrounds. This class will focus on skills essential to making square or rectangular frames. Skill building concepts will include how to break down and mill...
We're planning to have a tree cutting service come in and take out a couple of diseased trees in the back part of our lot and then hire someone else to dig out the stumps. These trees are at the base of a small rise, and we're thinking about cutting into the "hill" a little bit and making a low retaining wall, maybe 18" to 24" high. But that's just intended to move the shed back a bit from the house. (Our total lot size is only 5,616 feet with an 1,800 square foot house.) Landscaping change like this won't affect current drainage patters, but anything else might make it worse.
×