Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.
Rocking horses, toy chests and dollhouses are just a few of the classic gifts generations have treasured. Now you can give all the pint-sized DIYers on your list those same classic gifts, and make them yourself with the help of these DIY toy kits. They're perfect for kids of all ages, and will be treasured for years to come. The best part? All these gifts can still make it to your door by Christmas.

Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.


I would say take the shed, you'll find some use for it. I have contemplated this question also. I have a 20' x 11' basement shop, thats quickly loosing space. If you live in an area with a harsh winters (say the midwest), does it make sense to heat the shop through the week if you are only working in the shop on the weekends? Or do you run the heaters just when you are working in the shop? What kind of heaters are recommended (radient, wood stove, etc.)?
Windsor Design is an interesting brand in that it is not actually its own company. Instead, Windsor Design is one of the in-house brands sold by Harbor Freight. While it may be a store brand, that should not dissuade you at all as Harbor Freight is known for selling some of the best products available for all fields of construction. Granted, this may not strictly be the best table available, but it does provide a solid mix of features to make it a good value.

Workbenches have flat tops, though sometimes at the rear there is a cavity called a tool well that contains tools and components (and prevents them from falling off). One advantage of having the well set into the top of the bench is that, even with a variety of objects in the well, a large sheet of material can still be laid flat over the entire surface of the bench; the contents of the tool well offer no interference.


To mark the centerline, set a compass to span something more than half the width of the leg. Draw an arc from corner of the leg. The point where the arcs intersect will be on the centerline. With a centerline point on each end of the leg, place a scribe on the point, slide a straightedge up to touch the scribe. Do the same on the other end. When you have the straightedge positioned so that you can touch both points with the scribe, and in each case it is touching the straightedge - without moving the straightedge - scribe the line. Use scribes, rather than pencils or pens, because they make more precise marks.

AJ and Scott have been very helpful showing me where tools are my first few days there. This is a workshop where you will have to work independently. They will show you how to use certain machines for the first time and orient you to the shop itself but they will not help you with your project.  They can, however, be hired to help you with projects if that's what you need. I believe it's $75 an hour and limited to their availability. There is also a host of classes you can take if you want an intro into cabinet making, wood joining, turning etc. There are a lot of different classes that may pique your interests.
By following the Woodworking Course, Woodworking Classes or Start Your Own Woodworking Business Course, you eliminate mistakes most woodworkers make when working on their first project or starting their first woodworking business. Learn the importance of wood selection, joinery and tool purchases. You will understand how to start and make your new woodworking business successful.
So far, I really like the space. I signed up for a 3 month stint and hopefully will have some things to show for it. For my background, I took shop for 3 years in high school. I've always enjoyed working with wood but never had the space for it. I'm not a master craftsman but there are some really talented people there creating some nice pieces. All levels are welcome here.
Some tools required for this project are hole saw, drilling machine, pencil, tape measure, clamps, etc. This tutorial explains every step properly with images so that anyone can make a wooden sofa sleeve easily. Those, who prefer a video tutorial, can visit the below link to a YouTube video that illustrates the process of building a DIY Sofa Sleeve Cupholder.
Rocking horses, toy chests and dollhouses are just a few of the classic gifts generations have treasured. Now you can give all the pint-sized DIYers on your list those same classic gifts, and make them yourself with the help of these DIY toy kits. They're perfect for kids of all ages, and will be treasured for years to come. The best part? All these gifts can still make it to your door by Christmas.
I am sharing here a link to the detailed tutorial written by Pete at diypete.com, who shares the step by step process for making a wonderful barrel coffee table from scratch. He also tells you what items you’ll need for this project and where to find them. For example, you can buy an old whiskey barrel online or from a local whiskey store for a few bucks, if you haven’t already got one.
ALL Red Kits require planing and jointing of wood. Red Kits require the skill and tools to cut and make joints including panels. The woodworker needs to be able to cut, join, assemble and finish. Red Kits require the woodworker to be able to read the plans and to transfer images and dimensions from the plan to the lumber. It supplies all of the needed hand-selected, dimensioned lumber but woodworking knowledge and tools are recommended to be successful with Red Kits.
This rack can be built from old unused wood pallets you can find around the house. So it is also a great way to recycle those old pallets. You can also find a step by step tutorial at instructables.com for which I have included the source link below. This tutorial helps you to make a wood wine rack from the scratch. So what are waiting for? Just grab the items you need and start building a cool wooden rack for those nice wine bottles of yours.
The video explains the step by step process of making a nice wooden phone stand from scratch. My first wooden holder was not the best one, but it was good enough to motivate me to make more. I now possess 10 mobile wooden stands in different shapes and styles. And if I can make this, you too can make one yourself. Search the internet for more mobile holder ideas and start making one now.
Getting a smooth, blemish-free finish with oil-based polyurethane is within your grasp if you follow the steps in this article. Oil-based polyurethane varnish brings out the wood’s natural beauty or wood grain. Our 4-step approach shows you how to apply the varnish successfully. A good-quality natural-bristle brush, a reasonably dust-free, well ventilated space and some patience are all you need. Learn how to apply polyurethane.
The Classic Workbench is constructed entirely with in-compression-for-eternity drawbored mortise and tenons. It's as solid as humans can make it, short of growing a tree in the shape of a bench. The bench arrives at your shop completely assembled and ready to use. It doesn't knock down. The bench is built to the highest standards of traditional German craftsmanship in the utopian village of Amana Iowa. Our collaboration with the craftsmen in Amana, along with our experience in traditional workholding has yielded a workbench that is truly heirloom quality, but offered at what we think is a very reasonable price. We consider our flagship Split-Top Roubo as nearing the pinnacle of bench design (if there is such a thing) but we wanted to offer an essential bench built to high standards--an approachable but bulletproof tool for passionate enthusiasts of all levels, but especially intended for those just getting into the craft. Our principal bench maker has been steeped in the craft at the Amana Furniture Shop for nearly 50 years. Needless to say, a century and a half of woodworking tradition in Amana directly back to 19th century Germany speaks for itself. Many of the Amana craftsmen are multi-generational woodworkers.
The hacksaw will often damage the last thread when it cuts. Running a nut off the end will fix this. You'll have to run the nut all the way down from the other end. This doesn't take long, if you chuck up the rod in your drill and let it do the work. Hold the rod vertically, with the drill pointing down, and just hold on to the nut enough to keep it from spinning.

This place is so awesome. I just finished their cutting board class with Bob and it was a blast! he was very patient and informative. I showed him a handle I saw online and he actually helped me do it with my board and we ended up going over time of the class and I learned a ton (thanks bob!! You are the best!) I also took the wooden utensils class with tim and it was so much fun. I highly recommend this woodshop everyone there is so nice and down to earth
We have 4 newly expanded Classrooms, 3 state of the art labs with over $275,000 of new machinery, and $600,000 spent on new exhaust and compressed air systems. We have 4 new CNC production machines, a Haas VF-3 CNC Router and a NEWCNC 4×8 multi head machine and 2 Laguna IQ Routers. Even our shop stools (with cushioned backs) are brand new. We have new course offerings such as our Computer Design Sketchup Class and 8 new Certificate Programs you can choose from.
You may even want to put yourself in the picture. If your workshop space already exists, find a large piece of cardboard, wallboard, or plywood that’s about the size of the workbench top you envision. Find a couple of stools or chairs, perhaps a few books, and turn them into stanchions to support the “benchtop.” Is it too big for the space? Is it large enough for the tasks you envision will be performed upon it?
You may even want to put yourself in the picture. If your workshop space already exists, find a large piece of cardboard, wallboard, or plywood that’s about the size of the workbench top you envision. Find a couple of stools or chairs, perhaps a few books, and turn them into stanchions to support the “benchtop.” Is it too big for the space? Is it large enough for the tasks you envision will be performed upon it?
Save money by selecting the right woodworking tools you need to purchase. You will have an excellent understanding of what tools, equipment and workshop features you need to get started in woodworking. By purchasing only the right woodworking tools and equipment you need, you will save money, allowing you to invest in higher quality tools and woodworking machinery.
The 84-906 fits this bill perfectly as the table offers all of the qualities and features that you would expect but does not truly blow you away with any of them. For instance, this bench is made out of rubberwood. This wood is decent in that it provides the strength you want, but it is also extremely porous and rough-grained. The porous nature would generally make it susceptible to rotting and staining, though the bench has been lacquered. The rough grain will potentially cause tools to dull over time if you do not regularly relacquer it.
Getting a smooth, blemish-free finish with oil-based polyurethane is within your grasp if you follow the steps in this article. Oil-based polyurethane varnish brings out the wood’s natural beauty or wood grain. Our 4-step approach shows you how to apply the varnish successfully. A good-quality natural-bristle brush, a reasonably dust-free, well ventilated space and some patience are all you need. Learn how to apply polyurethane.

I drilled from the mark. That way I could ensure that the hole was where it was supposed to be, on the side where the position was critical. I have two 3/8" bits -- a brad point bit that came with my doweling set, and a perfectly ordinary 3/8" twist bit. Brad-point bits are far more precise than twist bits -- they're more likely to start where you want them to, and they're more likely to stay straight. My problem is that my brad-point bit wasn't long enough to go through 3-1/2" of wood. So I started each hole with the brad-point bit, then finished it off with the twist bit. I clamped a piece of ply on the back, to reduce tear-out.
As you can see in the image, this shelf goes on both sides of the corner wall. It looks beautiful and can be used to organize books, trophies, pictures frames and many other things. The strength and design of the shelf depends on how properly you build it. First time workers definitely need some guidance to help them with the process. Therefore, I am including this basic video that I found on YouTube that demonstrates the process of making corner wall wooden shelves.

Traditionally woodworkers  (joiners) learnt their craft working as an apprentice in the Master Craftsman's shop doing the grunt work and learning by assimilation over many years. Our approach is a little different. We're making the assumption that you're smart; are developing or already have a passion for woodworking; and can devote three months to intensive learning.
Applying the oil is easy. Put on some vinyl gloves, pour some oil in a bowl, take a piece of clean cotton cloth the size of washcloth or smaller, dip it in the oil, and apply it to the wood. You want the wood to be wet., you're not trying to rub it in until it's dry. Apply oil to the entire surface, and then go over it looking for dry spots, applying more oil as needed. After fifteen minutes of keeping it wet, let it sit for another fifteen minutes. Then apply another coat of oil, and let it sit for another fifteen minutes.
In this class we will explore the works of one of my favorite woodworkers, George Nakashima. This chair has elegance, simplicity, subtle details, and beauty. Don’t let its simplicity fool you. This chair requires great skill and precision to execute. It involves carving and sculpting of the seat with power and hand tools. The complex joinery has...
The projects in this course follow a natural progression of skills, techniques and tools. Some of the early student-made tools are, in fact, used to help make the next tool or bench fixture in the series. You are supported in the building of these projects with step-by-step outlines, knock-down examples and continuing, one-on-one consultations with the faculty. Periodic evaluations of your progress with a specific faculty-mentor help keep you on track.

Even with all of those faults my only regret is that it is too ugly. I didn’t take the time to make it more visually attractive as I was eager to get right into making beautiful furniture instead. Twenty years later the furniture is still beautiful (or not) but I go out to the shop and look at a drab uninspiring workplace. Yeah, nothing wrong with having a visually inspiring workplace in my opinion. All that shop furniture I slapped together years ago with no concern about aesthetics is getting replaced bit by bit. Why should my shop be downright ugly when it is one of my favorite places in the world to spend my time? I see no reason for that, but that’s just my opinion and as we all know everyone has their own one of those… Sadly, no one pays nor reveres me when I offer mine. bummer, I could be a rich egotistical maniac if they did coz I sure offer it enough. 😉
If you remember, when drilling the MDF I finished the holes from the other side using a Forstner bit. It made for a clean hole, but the positioning wasn't as precise as I really wanted. So for this, I decided to clamp a length of scrap MDF to the back side, and to drill straight through. My Forstner bits were too short, so I bought an extender. And then I found that the spade bits I was using gave a cleaner exit hole. Whooda thunk?
1. You mention doing other hobbies which I assume means stuff scattered around for various projects. (Don't tell me you do one at a time or are a neat freak!!!) How tall are the side walls to the shed? How high do you shuffle stuff around, i.e. flipping things over, moving wood around, etc? I can't imagine trying to do that in my shed, even if it were 2 ft higher than it's 7 ft center height. If you could build a platform in front it may help, especially if you can put removable cover over it (to please HOA).
×