Dip your toes in the world of woodworking with our week-long courses, and by the end of the week, you'll be swimming. During these intensive, week-long woodworking courses, you will benefit from the guidance of our expert furniture makers, learning the basic principles of woodwork and cabinet making to professional standards. Hone your technique with our classes and create precise, beautiful work with our expertise, equipment and advice at your disposal.
Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.
I don't see anywhere you mentioned the over all length of the bench top. A piece of 1 1/2" x 25" x 8' glued edge oak at Lumber Liquidators costs $192 including tax. Two piece is almost $400! Would that be better if I use two IKEA 1 1/4" x 25" x 74" solid Beech ($99 each plus tax) on top of a layer of 3/4" Birch plywood. That would be 3 1/4" over all.
I made a low table out of a couple of step-stools, my hollow-core door, and one of the MDF panels that would eventually form part of my top. I was concerned that any oil that dripped on the door might interfere with its glue adhesion, when I finally get around to the project for which I'd purchased it. The top side of the top sheet of MDF, though, I planned to oil, anyway. (Ditto for the bottom side of the bottom sheet.
The popular account showcases woodworking in a variety of ways. Many of the things they share are of artworks produced using its techniques—including My Modern Met favorite Gabriel Schama. Other posts highlight its practical applications in the form of furniture or flooring, while videos offer a look into the process and range from educational to oddly satisfying. Whether you’re a fan of woodworking or looking to try it yourself, @wooodworking will both mesmerize and inspire.
Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.
In ancient times, the woodworker’s bench consisted of a plank or split log with four splayed legs. Descendants of those benches are manufactured today, usually with a top of hardwood slabs glued together. The norm nowadays is four straight legs supporting the bulk above, often with braces and a shelf below. Despite the improvements, the linkage to Greek and Roman antecedents is still evident.
Our stationary equipment runs the complete range from heavy-duty industrial machines, to inexpensive home shop type of tooling so that each student can compare and contrast the range and versatility of equipment at a wide variety of price points.  We spend time on what makes a good machine good, an adequate one adequate, and a lousy machine worthless. We have no commercial sponsors and will share our opinions based on our experiences regarding the quality of one manufacturer over another.  There is no better place to kick the tires on a variety of equipment than at our shop.     

With the Grain: A Craftsman’s Guide to Understanding Wood by Christian Becksvoort. A little knowledge about trees goes a long way toward improving your woodworking. You don’t need a degree in dendrology to build a desk. But you do need intimate knowledge of how our raw material grows and – more importantly – how it responds to its environment after it has been cut and dried.
Practical Woodworking is a 50 hour comprehensive course that focuses on the necessary skills, tools, techniques, and safety to successfully enter the world of woodworking and furniture making. Beginner, intermediate, and advanced students learn about furniture design, construction, and finishing as well as wood behavior, hand tools, machines, milling from the rough, squaring, and joinery. It  is an intensive class for folks who want to continue woodworking in the future. It is a week of hard work with a lot of fun mixed in. Watch the video and read below for a more in-depth look at what we're all about.
I ended up making a number of practice cuts. The first revealed that I hadn't tightened the screws on the edge guide enough. The second revealed that the design of the edge guide provided very little support at the end of a board, because of the cut-out for the router bit. In the "Getting Started in Woodworking" video, they had screwed a piece of hardwood to the edge-guide, to provide a continuous -- and longer -- bearing surface. I may do that myself, some day, but I didn't have the materials at hand, so I clamped some 2x4 scrap to the end of each board, to provide a continuous bearing surface past the ends. The two grooves in the long stretchers and the side groove in the short stretchers have identical layout. I made practice cuts in scrap until I had the edge guide set correctly, then I cut them all with that one setting. The bottom groove of the short stretchers uses a different setup, so it was back to the scrap, before cutting them.
We have more than sixty years of excellence (1956-present) with an annual enrollment of more than 1,000 students in over 35 different classes.  The Palomar College Cabinet and Furniture Technology program offers the most comprehensive woodworking career curriculum in the nation. Utilizing three fully-equipped shops, our 2 full-time and 20 part-time instructors provide a breadth of courses and depth of expertise impossible to obtain in smaller programs.

While $115 may seem expensive, try accurately boring a grid of 20mm holes on 96mm centers in 3/4 MDF. I have for a table for our retirement community shop - - its a pita. Plus the MFT material seems denser and more water resistant than garden-variety MDF. And the single-thickness has proven sufficient the last several years on my original 1080s. Still dead flat.
After I left the magazine for a new job, I did all of my woodworking in my small two-car garage, but it was a struggle. Power, lighting, and temperature control were limited. And because I shared space with our cars I was always moving machines around, often while in the middle of a project. On top of that, my tool and machine collection had long since eclipsed the space. For all these reasons, fixing up the garage wasn’t an option. My finished basement is a family room, so it was out, too. An addition to the home or a stand-alone building would have been too expensive. I had to find a better path to a shop.
×