This place is great! They offer safety classes before you sign up for a membership, and the workspace is big and well maintained. I needed some basic lessons with table and band saws, which went great. I didn't ultimately get a membership because my sawing needs are very specific, and ended up getting a small bandsaw for myself at home. But if you're someone who needs the whole range of tools, this is the place to be!
Linseed oil sitting in a bowl, or spread on the surface of wood, is perfectly safe. But a linseed oil soaked rag provides a vastly increase surface area, so the oxidation happens faster, and the rag can provide insulation, trapping the heat. The increased temperature speeds up the oxidation even more, which raises the temperature even more, and the runaway feedback can quickly result in temperatures that will cause the rag to spontaneously burst into flame. This isn't one of those "do not drive car while sunscreen is in place" warnings. This is one of those "keep your finger off the trigger until you have the gun pointed at something you want to shoot" warnings. Rags soaked in linseed oil will catch fire, if you don't handle them properly, and they can do so far more quickly than you might think.
TOH has showed you how to make a toy chest with your kids before, but if you don't feel like cutting the wood yourself, opt for a kit like the one for this beautiful cherry chest. The kit comes with pre-cut pieces and all the hardware you need. Like many toy chests out there, the closed lid can also function as a bench seat, and the hinges are designed to prevent little fingers from getting caught. This model is available in three different finishes.
Although many hand tool operations are thoroughly covered, this is a machine based woodworking experience. You will find the school finely equipped with four table saws, four jointers, three drill presses, three thickness planers, a wood lathe, full dust collection, bandsaws, jig saws and scroll saws, 5 routers and dozens of router jigs and accessories. There is a heavy focus on the safe and efficient use of the table saw starting with it's basic operation and going into advanced production procedures. We consider the table saw to be an essential machine for efficient, accurate, and safe woodworking.
Even with all of those faults my only regret is that it is too ugly. I didn’t take the time to make it more visually attractive as I was eager to get right into making beautiful furniture instead. Twenty years later the furniture is still beautiful (or not) but I go out to the shop and look at a drab uninspiring workplace. Yeah, nothing wrong with having a visually inspiring workplace in my opinion. All that shop furniture I slapped together years ago with no concern about aesthetics is getting replaced bit by bit. Why should my shop be downright ugly when it is one of my favorite places in the world to spend my time? I see no reason for that, but that’s just my opinion and as we all know everyone has their own one of those… Sadly, no one pays nor reveres me when I offer mine. bummer, I could be a rich egotistical maniac if they did coz I sure offer it enough. 😉
The projects in this course follow a natural progression of skills, techniques and tools. Some of the early student-made tools are, in fact, used to help make the next tool or bench fixture in the series. You are supported in the building of these projects with step-by-step outlines, knock-down examples and continuing, one-on-one consultations with the faculty. Periodic evaluations of your progress with a specific faculty-mentor help keep you on track.
A workbench needs to be heavy enough that it doesn't move under you while you're working, and stiff enough that it doesn't rack itself to pieces under the forces that will be placed upon it. It doesn't take many hours of planing a board or hammering a chisel for a worktable made of nailed 2x4s to come apart. Traditional bench designs use mortise-and-tenon joinery, which is strong and rigid, but not really suited for a novice woodworker who doesn't already have a bench.
Save money by selecting the right woodworking tools you need to purchase. You will have an excellent understanding of what tools, equipment and workshop features you need to get started in woodworking. By purchasing only the right woodworking tools and equipment you need, you will save money, allowing you to invest in higher quality tools and woodworking machinery.
With the top laying on the floor, bottom side up, the next step is to flip the base upside down, and attach it to the top. I followed Asa Christiana's design, in using s-clips. When I stopped by my local Woodcraft, though, they only had two packages of ten, so I didn't use as many as I would have, otherwise. For the top I put four on each side and two on each end. For the shelf I put three on each side and two on each end. If it turns out that I need more, I can always add more.
I mocked up the two scenarios, and determined that with the plate inside the stretcher the vise would have a reach of 8 inches, and with it outside the stretcher it would have a reach of 9 inches. I decided that 8 inches was enough, and that the extra inch wasn't worth the extra effort. With the end vise mounted like this, the right edge of the top would have no overhang.
Once you start spreading glue, you have maybe five minutes to get the two panels mated, aligned, and clamped together. So make sure you have everything on-hand, and you're not gong to be interrupted. Start squeezing out the glue on one MDF panel, and spreading it around in a thin, even coating, making sure you leave no bare areas. Then do the same to the other MDF panel. Then pick up the bottom panel and flip it over onto the upper panel. Slide it around some to make sure the glue is spread evenly, then line up one corner and drive in a screw. Line up the opposite corner and drive in a screw there. Clamp all four corners to your flat surface, then start driving the rest of the screws, in a spiral pattern from the center.
This is used to secure workpieces in place while you work on them – often for jointing. The location and capacity are the important things to look at. Most vices will come on a right-hand configuration either on the front or the side of the bench. If possible, it is a good idea to look for vices that can be repositioned. In terms of capacity, anything over 5” is solid while anything under 4” is likely a bit too small for all projects.
A couple nice qualities about this bench include the weight and vice capacities. The weight capacity of this bench is 330 pounds which is decent, though it will not wow you too much. The vice, on the other hand, provides a 7” capacity which is tied for the most on our list. That said, there is only a single vice, and it is not able to be repositioned. This can make things a bit frustrating for lefties as it is a right-handed configuration.
I am new to woodworking. I'm learning as I go along, and I'm documenting as I learn, in the hope of being helpful to other novices. On the range from slap-dash to deliberate, my method is definitely on the deliberate side. If you have enough experience to be confident in using techniques that are more time-efficient, go for it. The techniques I'm using are those I thought least likely to go wrong, not those that would produce a product in the shortest time or at the lowest cost. You'll notice that I made a number of mistakes, spent considerable time on work I later determined to be unnecessary, and in a number of cases I used different techniques at the end than I did at the beginning. These are all the result of learning. I thought it would be better to demonstrate how I made errors, and how I corrected them, than to provide a set of instructions that presented the false impression that everything went together perfectly.
I love the opportunity Community Woodshop provides to take advantage of the tools, high-end equipment and hands on skills they'll assist you with when working with woods and metals. I'm not too sure about the Community part because I'd probably not come back because of the distance, however I do recommend learning to build shit on your own rather than paying a hefty price for the same materials that all furniture and fixtures and most jewelry are made of. They offer a wide variety of classes that teach you skills to build different items and use different tools.
The Cape Ann Shed was designed with coastal New England in mind. So yard work may feel like you’re actually on vacation. From Cape Cod to the beaches of Maine, you will find a Post Woodworking Cape Ann shed adorning the yards of thousands of homes. It’s a popular style with our customers – whether they make their home by street or by sea. An affordable choice for an outdoor structure, the Cape Ann brings functional elements with nautical appeal.