The holes we want to mark are the holes through which the threaded rod connecting the two legs will run. This threaded rod will run through the 3/8" groove along the bottom of the short stretchers,. The hole for the upper stretcher has to be positioned so that when the rod is running through this groove, the top of the short stretcher is even with the top of the legs. The most precise way I've found for marking the position of this hole is to use a dowel center. Fit the dowel center into the bottom groove, line up the stretcher, and bang on the end with a rubber mallet. The dowel center will leave a mark indicating the center of the hole.
I was a short-term member at Community Woodshop, but it's left a lasting impression on me! They have everything you need to build a variety of projects, and i definitely got some good use out of their quality equipment. The staff is very knowledgeable and friendly, and are always around to offer sound advice and to make sure you have a safe setup. I only discontinued my membership due
A steam box and a heat source are the two main components used to steam bend wood. Steam boxes must be able to withstand large fluctuations in temperature and humidity without breaking apart. In this two-hour workshop, students will build an optimized steam box that can last through the tough job of steaming wood, allowing them to continue creating their own projects at home!
Whether you’re setting up a new shop or upgrading your old one, a good, sturdy workbench will almost surely be central to your plans. We can help. Our editors and contributors have produced more than two dozen articles and videos about benches and assembly tables. We’ve included everything from a simple but workable plywood bench to a classic hardwood bench complete with vises. You’ll also find full project plans, as well as tips for installing vises, making your bench portable, adding storage, and more. Some of our workbench plans are free, and the rest can be purchased in our store (check the links below).
The bench would end up being about 5 feet long. I thought about cutting 5 feet out of my 8 feet long countertop and use the rest for a small support table. However, after a consideration, I decided to bypass the front vise altogether together with the overhang so my bench will be 4 feet long. This allows me to skip the MDF and just glue the two halves of the 8 feet board together.
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.

The video explains the step by step process of making a nice wooden phone stand from scratch. My first wooden holder was not the best one, but it was good enough to motivate me to make more. I now possess 10 mobile wooden stands in different shapes and styles. And if I can make this, you too can make one yourself. Search the internet for more mobile holder ideas and start making one now.


The oldest woodworking shop in America has been discovered virtually untouched in Duxbury, Massachusetts. The extremely rare find reveals an 18th century joiner’s shop with the date ‘1789’ painted in the rafters. University of Delaware professor Ritchie Garrison came upon the historic structure on the site of a preschool, bringing several experts out to verify its age. Craftsmen used the shed to create intricate woodwork.


An excellent introduction to woodworking is to use crates as your main material. The boxes are already formed, which means less assembly work for you—yet it looks impressive once your project is altogether. With this crate coffee table, you still get to practice your skills adding the casters and the center box. Finish with a little stain, and this table is ready to roll. You can find the full tutorial at DIY Vintage Chic. 

For one, the bench itself is a good size. While its width as a tad short at just over 1 ½’, the length is a great 5’ long. Even better, this bench is made out of birch wood. Birchwood is similar to beech in that it is strong but soft enough to prevent inadvertent dulling of your tools. However, birch has a bit of an advantage over beech in that it is not a porous which makes staining on the Windsor Design a more worry-free affair.


For most of the course, we'll be heavily focused on developing your skills using hand tools. As a developing woodworker, there is no substitute for putting in the hours of direct hands on practice it takes to gain an intuitive understanding of wood. The early part of this course focuses on working with hand tools as we believe they bring you closer to wood as a material.  You can rip a board on a table saw with out much thought to the wood itself, but you will understand much more about grain if you rip a board with a hand saw.  As the course progresses, machine processes are introduced as a pragmatic aid in expediting projects.  
The course successfully meets the needs of multiple experience levels in a safe, well equipped, spacious, congenial, and educational environment. All instruction and lab experience is under the personal direction of master woodworkers as well as one or two additional experienced woodworkers/teacher assistants who are on hand during all lab hours providing roughly a three-to-one student-to-instructor ratio. Intermediate to more advanced students should not be put off by the fact that beginners are also included in this course.  Check out some of the work done by our alumni in the Alumni Furniture Gallery to get an idea of what our students are capable of.
In ancient times, the woodworker’s bench consisted of a plank or split log with four splayed legs. Descendants of those benches are manufactured today, usually with a top of hardwood slabs glued together. The norm nowadays is four straight legs supporting the bulk above, often with braces and a shelf below. Despite the improvements, the linkage to Greek and Roman antecedents is still evident.
If you don't quite have the space for a real pony, make this handcrafted wood version instead. The horse pictured here is unfinished pine, but there are lots of woods and finishes to choose from. Everything you need comes with the kit, and the plans can be downloaded. If you don't want to build it yourself, you can order from the website—just allow two to three weeks to ship.
I was a short-term member at Community Woodshop, but it's left a lasting impression on me! They have everything you need to build a variety of projects, and i definitely got some good use out of their quality equipment. The staff is very knowledgeable and friendly, and are always around to offer sound advice and to make sure you have a safe setup. I only discontinued my membership due

Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.
Palomar Community College in San Marcos, located about 35 miles north of San Diego, offers certificate, degree and life-long learning programs to more than 20,000 students a year. In particular, the Cabinetmaking and Furniture Technology Department offers in excess of 50 classes annually, and the present faculty is composed of four full-time teachers, 21 part-time instructors and 11 teaching assistants. As of Fall 2013, woodworking students will have access to a newly remodeled woodworking facility equipped with three machine rooms, three bench rooms, a saw mill and a finish room.
Constructed with the classic craftsmanship that Grey’s Woodworks is known for, our beautiful sheds come in a variety of styles, sizes and colors. We will help you design a shed to match your surroundings and meet your needs. Select from our pine tongue and groove, duratemp T1-11, or vinyl sidings and arrange doors and windows to your liking. All of our sheds are handcrafted in modern workshops. Not only does a shed from Grey’s Woodworks provide much needed storage space for your mower, snow blower or bike, but it also makes for an attractive addition to your property.
Save money by selecting the right woodworking tools you need to purchase. You will have an excellent understanding of what tools, equipment and workshop features you need to get started in woodworking. By purchasing only the right woodworking tools and equipment you need, you will save money, allowing you to invest in higher quality tools and woodworking machinery.
Though the preschool had been using the woodworking shop for storage, not realizing its historic value, it’s still in remarkably good shape. The woodworking benches and tables are still in excellent condition. According to Garrison, the shop is filled with clues as to how it was used. Some benches were covered in paint while others bear saw marks, testifying to the variety of tasks that were performed there.
With the shelf secure, get a couple of friends to come help, and stand the bench on its feet. I said earlier moving the top by yourself is dangerous. Trying to lift the entire bench is foolhardy. Of course, I already said I'm stubborn, so I did it myself by rigging a simple block-and-tackle using lightweight pulleys I got at the hardware store. (Not the lightest-weight pulleys, those are meant for flag poles and have a design load of something like 40 pounds. These had a design load of 420 pounds.)

I'm not kidding when I say that this shop has everything you need to make a project happen.  They are not only equipped but also some of the nicest people.  Supportive and, mostly, willing to help you with your project.  The idea is for you to do it on your own, but if you get stuck I have yet to see someone say, "no, figure it out on your own."  they are helpful and fair.  I love this place, and the people I have met there.


The edges of MDF are fragile, easily crushed or torn. MDF is also notorious for absorbing water through these edges, causing the panels to swell. In Sam Allen's original design, he edged the MDF with 1/4" hardboard. This edging is one of the complexities that Asa Christiana left out in his simplified design. I think this was a mistake. MDF really needs some sort of protection, especially on the edges.

Something like this really does look like it would be a fun project. I guess I need to go out to the yard and use some stakes and brightly colored taped to mark off some different dimensions (12x8, 12x10, 12x12, etc.) to figure out just how big I can make this thing. If I'm building it myself, it'll be easy to keep the height right at the 9 foot limit.
×