Looking for a great gift for a friend or family member or maybe a Christmas gift? Recommended woodwork projects include a turned wood box with a lid or how to make a jewlery box. New to woodworking? Great! Check out these simple beginner’s woodworking projects. No matter the DIY woodworking project you can find your next gift idea in the wood craft videos listed below.
A steam box and a heat source are the two main components used to steam bend wood. Steam boxes must be able to withstand large fluctuations in temperature and humidity without breaking apart. In this two-hour workshop, students will build an optimized steam box that can last through the tough job of steaming wood, allowing them to continue creating their own projects at home!
Fundamentals Of Fine Woodworking With Taeho Kwon (Evening Class) The secret to fine woodworking can be found in the pursuit of the fundamentals. With high-tech machines and power tools, these fundamentals can be overshadowed. In this class we will learn the values of design, drawings, mock-ups, sharpening, care and use of hand tools, tuning up a bench...
You don’t need a fully equipped shop to enjoy woodworking! In this class, you will learn to design, make, and finish a unique wood box. With an emphasis on tool safety and material exploration, we will use a combination of power tools and hand tools to make boxes of all shapes and sizes. Beginning with a solid block of wood, you will learn how to lay out, cut, sculpt, and reassemble the block into the form of a box. Demonstrated techniques will include hidden hinges, small drawers, pull knobs, and fitted lids, as well as texturing, carving, burning, painting, and finishing. Suitable for beginning and intermediate students, all materials provided.

This is my first post here but been lurking for a while. I am currently working in a 10x14 shed which has sufficed nicely until my recent purchase (sunday) of a new Craftsman table saw model OR35505. This I discovered ate a lot of space but with some reorganization and some good casters, it's going to work. I did add a window AC unit and will need to figure out some heat but hoping to have built a better shop with HVAC before it's too cold.
Permanent or Portable? This is a distinction that decides much about your bench choice: Is it to remain stationary or must it fold, roll, or otherwise make itself scarce between jobs? Large, heavy benches are more stable and, in general, more adaptable to different jobs (sometimes several at once). But the bigger the bench, the more hassle involved with stowing it.
First, we need to drill out the holes for the screws that will hold them together. While the two layers of MDF are glued, the countertop and the MDF will only be screwed. The oak countertop, like any natural wood product, will expand and contract with humidity changes. If it were glued to the MDF, the difference in expansion of the two layers would cause the countertop to buckle and curl.
This is used to secure workpieces in place while you work on them – often for jointing. The location and capacity are the important things to look at. Most vices will come on a right-hand configuration either on the front or the side of the bench. If possible, it is a good idea to look for vices that can be repositioned. In terms of capacity, anything over 5” is solid while anything under 4” is likely a bit too small for all projects.
If you opt for a bench with drawers or cabinets built into its base, don’t forget the toe spaces: Leave a space roughly three inches deep and four inches wide at floor level for your toes, just like kitchen cabinets. The absence of a toe space means you’ll be forever kicking the face or sides of the cabinets which is irksome and, with tools in hand, potentially dangerous. And you’ll have to lean over farther to reach the back of the benchtop.
If the holes of the first jaw are in the proper position, drill holes in the same locations on the other jaw. I lined the drilled jaw on top of the undrilled jaw, clamped things down, and then drilled about 1/4" into the undrilled jaw, to mark the location. Then I removed the drilled jaw and drilled out the marked locations the same way I did the first.
While $115 may seem expensive, try accurately boring a grid of 20mm holes on 96mm centers in 3/4 MDF. I have for a table for our retirement community shop - - its a pita. Plus the MFT material seems denser and more water resistant than garden-variety MDF. And the single-thickness has proven sufficient the last several years on my original 1080s. Still dead flat.
For your kitchen, it can work as a knife rack. It gives you easy access to all essential tools while saving space. In addition, it adds a nice visual appeal to your kitchen wall. You can customize your wall rack with different materials, designs and styles. I am here sharing the source link to the step by step tutorial about how to make a rustic wall knife rack.
After I left the magazine for a new job, I did all of my woodworking in my small two-car garage, but it was a struggle. Power, lighting, and temperature control were limited. And because I shared space with our cars I was always moving machines around, often while in the middle of a project. On top of that, my tool and machine collection had long since eclipsed the space. For all these reasons, fixing up the garage wasn’t an option. My finished basement is a family room, so it was out, too. An addition to the home or a stand-alone building would have been too expensive. I had to find a better path to a shop.
×