The hacksaw will often damage the last thread when it cuts. Running a nut off the end will fix this. You'll have to run the nut all the way down from the other end. This doesn't take long, if you chuck up the rod in your drill and let it do the work. Hold the rod vertically, with the drill pointing down, and just hold on to the nut enough to keep it from spinning.
The decision to be made with respect to the end vise is whether the support plate should be mounted to on the inside or on the outside of the stretcher. Mounting the plate on the inside of the stretcher reduces the reach of the vise - it can't open as far, because the support plate is back from the edge by a couple of inches. But mounting the plate on the outside of the stretcher means that we need to add some support structure for the inner jaw of the vise, which the legs would have provided if we'd mounted the plate on the inside.
If you're using drywall screws, you'll want to countersink the holes. Drywall screws are flat-head, and need a countersink to seat solidly. If you're using Kreg pocket screws, the way I did, you won't want to counter-sink the holes. Kreg screws are pan-head, and seat just fine against a flat surface. Both drywall screws and Kreg pocket screws are self-threading, so you don't need pilot holes in the second sheet of MDF.
You can buy sandpaper, glue, and other consumables from them for a nominal price. Their hand tools are propitiatory though so you would have to buy a specific kind of orbital sandpaper, for example. You couldn't just get generic. They are reasonably priced though. There is literally a coffee can with money in it and prices written on the boxes with these consumables. If you think you might burn through enough sand paper on something, check the brand and price shop.
Had a great experience at the shop! My schedule is hectic and unfortunately can't make the classes, but I did do a private lesson with Bob.  In one afternoon, we created two cutting boards.  Bob was very detailed with breaking down the process and using the machines.  Honestly didn't expect to make two cutting boards but Bob was proficient with time.  I got really comfortable using the machines especially the table saw.  I learned how to use the planer, jointer, miter saw, table saw, drill press, router, disk sander, and random orbital sander.  Really recommend folks that are interested in woodworking with little to no experience to take the Safety Orientation and the Cutting Board class or private lessons.  Looking forward to my next project at the shop!

Although many hand tool operations are thoroughly covered, this is a machine based woodworking experience. You will find the school finely equipped with four table saws, four jointers, three drill presses, three thickness planers, a wood lathe, full dust collection, bandsaws, jig saws and scroll saws, 5 routers and dozens of router jigs and accessories. There is a heavy focus on the safe and efficient use of the table saw starting with it's basic operation and going into advanced production procedures. We consider the table saw to be an essential machine for efficient, accurate, and safe woodworking.
Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.

You may even want to put yourself in the picture. If your workshop space already exists, find a large piece of cardboard, wallboard, or plywood that’s about the size of the workbench top you envision. Find a couple of stools or chairs, perhaps a few books, and turn them into stanchions to support the “benchtop.” Is it too big for the space? Is it large enough for the tasks you envision will be performed upon it?
While $115 may seem expensive, try accurately boring a grid of 20mm holes on 96mm centers in 3/4 MDF. I have for a table for our retirement community shop - - its a pita. Plus the MFT material seems denser and more water resistant than garden-variety MDF. And the single-thickness has proven sufficient the last several years on my original 1080s. Still dead flat.
During an intensive six-month course, not only will you learn all of the basics such as the different tools you will be using but also get a chance to try some of our more advanced projects. These will include how to draw up a big project such as a workbench, and French Polish your own jewellery box. You will also learn how to draw and can take part in our design courses, an invaluable part of the making process.
In this class we will explore the works of one of my favorite woodworkers, George Nakashima. This chair has elegance, simplicity, subtle details, and beauty. Don’t let its simplicity fool you. This chair requires great skill and precision to execute. It involves carving and sculpting of the seat with power and hand tools. The complex joinery has...
You don’t need a fully equipped shop to enjoy woodworking! In this class, you will learn to design, make, and finish a unique wood box. With an emphasis on tool safety and material exploration, we will use a combination of power tools and hand tools to make boxes of all shapes and sizes. Beginning with a solid block of wood, you will learn how to lay out, cut, sculpt, and reassemble the block into the form of a box. Demonstrated techniques will include hidden hinges, small drawers, pull knobs, and fitted lids, as well as texturing, carving, burning, painting, and finishing. Suitable for beginning and intermediate students, all materials provided.

Timberframing is a traditional technique for building large and small structures using only wooden joinery. Prized for its structural integrity and beauty, as well as reliance on hand skills, timberframing is regaining popularity in modern applications. We will start with an overview of the different styles and aesthetics involved, and move into the specific tools that are used to lay out and cut the strong joints. Each student gets guided practice time making sample joints. We will all work together to make a small structure that can be raised on the final day of class.
Clamp the inner jaw of the end vise in position, leaving a little bit to trim off later, and then use the dowel and dowel center trick through the screw and guiide rod holes of the vise base plate to mark the position of the screw and guide rod holes in the jaw. Remove the jaw and drill 1-1/8" holes in the marked positions. I used the drill guide for most of the holes, and drilled freehand for the last bit. When you're starting a spade bit in a deep hole like this, start the drill very slowly, and the bit will move the drill into a perpendicular position. Start it too fast and the bit will bind and you'll damage the sides of the hole.
Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.
I don't like to be ignored either. I came the same day Mahndo left after waiting 30-45 mins. I left a note with name and number but no one even called me back. I was completely ignored. I found a class over at The Corona Heritage Park in Corona instead. Their instructor answers when I call or text. Nice to be acknowledged! Going to finish beginning and take advantage of the key access in their intermediate class.
What I did, when I came back, was to clamp down the strip where it had torn away, and then to start routing from the other end. I still moved the router from right to left, but I did it in six-inch sections, taking light passes, and sort of whittled the strip flush. As the sections I was working were farther to the right, the strip was thinner. Eventually I came to where I was trimming the strip away entirely, at which point I took off the clamps and the remainder fell away.
Tuition for Practical Woodworking is $1200 for six 8-hour days of instruction and active woodworking. Lumber is provided and costs an additional $85. We provide most tools, students are only required to bring a tape measure, sharpie, pencil, and eye protection (sanders and sandpaper are encouraged if you've got them).  Visit our Course Project page to see the table we make!

Not sure about Midwest but I have a 24 x 14 Game rm attached to my shop and I put a small window unit/heat pump in the wall. It stays comfortable all year round. It get really hot here and we had a several day in the 20's this winter but it's insulated well. That might not be as cold or as hot as in some places but the unit I haze does not run that often and has a low cost rating. I'm planning on putting a larger unit in the shop area even though I do like to work with the garage door open. The door is insulated so I can run A/c in there. Just my .02.

2 - use a plunge router with a bottom bearing cuter bit such as this from rockler: http://www.rockler.com/product.cfm?page=25160&site=ROCKLER .... I thought to use the short one as I plunge it directly downward in the centre of the hole until the bearing reaches within the tabletop hole. I suppose one could use a long one, but the stubbiness seemed more practical (the big bearing ensured accuracy?)


Another wooden item that I love very much is a beautiful mobile holder. You can see one in the image below. These things are not only beautiful, but they can comfortably hold any sized mobile and ensure proper safety. Another amazing thing is that they can be built in many shapes and sizes, as and how you need it. You can see some more examples at the source below
This place is so awesome. I just finished their cutting board class with Bob and it was a blast! he was very patient and informative. I showed him a handle I saw online and he actually helped me do it with my board and we ended up going over time of the class and I learned a ton (thanks bob!! You are the best!) I also took the wooden utensils class with tim and it was so much fun. I highly recommend this woodshop everyone there is so nice and down to earth
The Practical Woodworking course at the JD Lohr School of Woodworking is a complete and comprehensive woodworking course held in our shop on the 13-acre farm in southeastern PA. This is total immersion woodworking for ambitious, interested adults. With class size limited to 11 students and 3-4 instructors in each class, all needs of every student are met regardless of experience level. If you are self taught with no formal training as a woodworker, this course will quite literally change the way you work.

The end vise will have both jaws made out of 1-1/2" thick oak. The front vise has its moving jaw made of 1-1/2" oak, but uses the edge of the bench as its stationary jaw. So while for the end vise, if we mount it lower, we can make both the jaws deeper to compensate, for the front vise we cannot, so we want it mounted as close to the edge of the bench as possible.
We follow many traditional standards because they impart the work ethic of doing things right, emphasizing quality, attention to detail, considering impact and longevity, and working to high standards for lasting work.  Our instructors are experienced craftspeople who recognize the value of passing on their skill set to the next generation of woodworkers.  We strive to invite you into our community by connecting you with others who have a passion for craftsmanship.  
I’ve built workbenches with more than 100 students. In every class, there’s one guy who wants to put a vise on every corner of the bench. Not because it’s a partner’s bench for two people. Just because he wants it that way. While I support your freedom to choose, I also don’t want to spend two weeks installing complex tail-vise hardware on your bench when we could be building furniture instead.

I don't see anywhere you mentioned the over all length of the bench top. A piece of 1 1/2" x 25" x 8' glued edge oak at Lumber Liquidators costs $192 including tax. Two piece is almost $400! Would that be better if I use two IKEA 1 1/4" x 25" x 74" solid Beech ($99 each plus tax) on top of a layer of 3/4" Birch plywood. That would be 3 1/4" over all.


Although many hand tool operations are thoroughly covered, this is a machine based woodworking experience. You will find the school finely equipped with four table saws, four jointers, three drill presses, three thickness planers, a wood lathe, full dust collection, bandsaws, jig saws and scroll saws, 5 routers and dozens of router jigs and accessories. There is a heavy focus on the safe and efficient use of the table saw starting with it's basic operation and going into advanced production procedures. We consider the table saw to be an essential machine for efficient, accurate, and safe woodworking.
Those bums even have a stipulation that you can't connect any utilities to a shed. My plan is to adhere to the letter of the law if not the spirit. I plan to run a buried 20 amp power line out to the shed (this will be done professionally and properly according to whatever is required by the law), but it will require a manual connection to a junction box on the outside of my house to complete the circuit. That way, I can argue that the electrical connection is only temporary and is little more than a safe and buried version of an extension cord.
×