Why would you buy a costly platform bed from Ikea or somewhere else when you can make one yourself at home? Oh yes, you can. A bed is the most common furniture piece used in the house and probably the costliest one. Wouldn’t it be great if you could just make a bed of your own, without having to spend many bucks for buying one? So I am here sharing a great tutorial to help you to build a nice comfy platform bed that you can use anywhere in the house.

When you have the other leg seated, the threaded rods will extend father than you want them to. You'll want to mark them so they can be cut to length. Place a washer and a nut on each threaded rod, and then tighten down the nut to pull everything tight. Depending upon the wrench you are using, and how much longer the rod is than it needs to be, you may find it necessary to stack up a number of washers, so that the nut is positioned where the wrench can operate on it.
You're not the first person to say this! I'm half inclined to use the Lowes shed as a starting point for my own design. But I do think I'd feel better if I could work as an "aprentice" next to an "old master". Someone at work is going to put me in touch with a guy who builds sheds for a living, and apparently he's competitive with the prices @ Lowes and HD. The Lowes shed comes with a "Handman Package" that I don't want but would end up paying for, anyway. The "workbenches" were laughably flimsy.

This bench suffers from no such limitations as it provides an incredibly solid and stable workspace, albeit in a somewhat stripped down version. In terms of performance, Sjobergs tops our list at providing 80 lbs of weight capacity. This is one of the more quantifiable measurements to determine the quality of a work bench’s craftsmanship. This is achieved by using thick pieces of European birch wood and working it without using lower end joints – like butt joints.
If you remember, when drilling the MDF I finished the holes from the other side using a Forstner bit. It made for a clean hole, but the positioning wasn't as precise as I really wanted. So for this, I decided to clamp a length of scrap MDF to the back side, and to drill straight through. My Forstner bits were too short, so I bought an extender. And then I found that the spade bits I was using gave a cleaner exit hole. Whooda thunk?

Though still straightforward in design, this bench distinguishes itself from many of its competitors with the sheer wealth of storage options. It includes two drawers of equal size with an additional drawer of double size as well as a spacious cupboard. Altogether, this provides for more storage space and organization than any other workbench we reviewed. Of course, this bench also comes with many of the same advantages and disadvantages that you would expect to see on other models within this lineup.
Learn the basics of woodworking with simple hands-on projects to build your confidence and skills. Each lesson in this class explores an area of woodworking that will form the building blocks of all future woodworking projects you undertake. Keeping the average DIY'er in mind, this entire class is conducted using basic handheld power tools, with no fancy fixed tools like table saws, lathes, planers, or drill presses.
All glue & stain benches are made using a solid maple frame for lasting durability and strength. Side Clamp Benches are made specifically for bar clamps, and are used for gluing projects or clamp storage. Benches feature an open top with 17 sets of 3/4"W grooves that accept bar clamps measuring 3’ and over. Lower center rail is adaptable for storage of hand screws and C-clamps. Side clamp benches are available with or without a drip pan. Glue & Stain Benches are made with a 1-1/4” plywood top covered with heavy-coated galvanized steel. Bottom shelf has a 4” rear retaining lip. Glue and stain benches are available with or without casters. Limited Lifetime Warranty. 

I wanted the left edge of the jaw of the front vise to be flush with the left edge of the top, the right edge with the left edge of the left front leg. So the amount of overhang on the left depends upon the width of the front vise jaw. The width of the jaw is, at a minimum, the width of the plate that supports it, but it's normal to make the jaw extend a bit beyond the plate. How far? The more it extends, the deeper a bite you can take with the edge of the vise, when, for example, you are clamping the side of a board being held vertically. But the more it extends, the less support it has. I decided to extend by 1-12", which gives me a 2-1/2" bite, and which should still provide solid support, given that the jaw is 1-1/2" thick. This means the top needs a left overhang of 12-1/4".


With the top laying on the floor, bottom side up, the next step is to flip the base upside down, and attach it to the top. I followed Asa Christiana's design, in using s-clips. When I stopped by my local Woodcraft, though, they only had two packages of ten, so I didn't use as many as I would have, otherwise. For the top I put four on each side and two on each end. For the shelf I put three on each side and two on each end. If it turns out that I need more, I can always add more.
The procedure is very easy to understand and follow for anyone with a little woodworking knowledge. Make sure to collect all the items you need before you start with the project. You may even ask Tracy your queries directly in the comment section of the tutorial post. Or you can ask them here. Either way, I hope that you manage to build this one nicely.
My first shop was a 8 x 10 ft room, actually a bedroom, with 10 ft high ceilings in a older home in Chicago. I had a 10" Craftsman TS, drill press, 8 1/4" Skil saw which still works, some welding tanks, hand tools and... my bed was a loft across the 10 ft length 4 ft down from the ceiling with a ladder against the wall to get up. I was 16 yrs old then, now I am 66 yrs, have 2 shops with Craftsman power tools up stairs, and Grizzly tools ,a Powermatic 68, a MIG welder, and other tools on the ground floor. I've come a long way, You think? I remember making bases for sculptures called "plinths", my first commission, in the living room, 5 pieces rather large, several ft long and wide. The house was haunted, and my mom told the "spirit" to leave and go back downstairs. There was a cold draft and the straw chair would rustle with no one sitting in it. Wow, does that bring back memories from the '60's.
With the Grain: A Craftsman’s Guide to Understanding Wood by Christian Becksvoort. A little knowledge about trees goes a long way toward improving your woodworking. You don’t need a degree in dendrology to build a desk. But you do need intimate knowledge of how our raw material grows and – more importantly – how it responds to its environment after it has been cut and dried.

Looking for a great gift for a friend or family member or maybe a Christmas gift? Recommended woodwork projects include a turned wood box with a lid or how to make a jewlery box. New to woodworking? Great! Check out these simple beginner’s woodworking projects. No matter the DIY woodworking project you can find your next gift idea in the wood craft videos listed below.


With the top laying on the floor, bottom side up, the next step is to flip the base upside down, and attach it to the top. I followed Asa Christiana's design, in using s-clips. When I stopped by my local Woodcraft, though, they only had two packages of ten, so I didn't use as many as I would have, otherwise. For the top I put four on each side and two on each end. For the shelf I put three on each side and two on each end. If it turns out that I need more, I can always add more.
My bench is MY BENCH. In other words, it’s a thing of evolutionary beauty. I built the top 10 years before deciding on and designing the base. I spared no absurdity. It is supremely stout and the much maligned drawers are accessible from either side. The larger drawers have dust lids and can be extended to provide support for large workpieces or as a step for climbing on top of the bench. The top alone weighs more than most Roubos. So NYAH! Did I mention that I designed it to fit in with the Arts & Crafts vernacular? Who said you can’t build your bench to be furniture? Beautiful as well as useful shop furniture? Just sayin…
The bench I will be describing differs from both of these in a couple of areas, the most significant of which is the top. Allen's top was made from three layers of 3/4" medium density fiberboard (MDF), topped and edged with 1/4" hardboard. Christiana's top was just two layers of 3/4" MDF. My top is two layers of 3/4" MDF edged with 1/2" oak and topped by a 1-1/2" thick edge-glued oak Ikea countertop. My top is more expensive in both time and money than either Christiana's or Allen's. If you're looking to build something fast and cheap, I'd recommend Allen's approach over Christiana's. The hardboard significantly increases the durability of the top.
A woodworking school teaching furniture making techniques located in Pennsylvania. Beginner through advanced students will learn solid wood furniture construction using traditional and modern techniques. The classes emphasize wood movement, practical methods, efficiency (with machines and hand tools), design, milling, joinery, finishing, and safety. Woodworking and furniture making courses are offered to aspiring crafts men and women throughout the country.

 I have always wanted to share this wonderful woodworking world with like-minded people from all over the world. For the last six months, I have started sharing Japanese woodworking information through videos and photos. Because of the huge amount of interest, I started organizing one-day workshops for people visiting Kyoto, letting them experience Japanese woodworking tools.
Practical Woodworking is a 50 hour comprehensive course that focuses on the necessary skills, tools, techniques, and safety to successfully enter the world of woodworking and furniture making. Beginner, intermediate, and advanced students learn about furniture design, construction, and finishing as well as wood behavior, hand tools, machines, milling from the rough, squaring, and joinery. It  is an intensive class for folks who want to continue woodworking in the future. It is a week of hard work with a lot of fun mixed in. Watch the video and read below for a more in-depth look at what we're all about.
Thinking about transitioning into serious woodworking, but don't have half a year or more to spare? Our one-month fine woodworking courses are perfect for those who are looking to move towards professional woodwork, but can’t find the time to commit to a longer course. Here, our woodworking classes will intricately teach you all of the basics, the same as you would for our three, six and twelve-month courses, with projects specially-created for both beginners and the more experienced. This will truly bring your woodworking skills up to the high level of craftsmanship needed within the industry.
In this two day class we will reveal some of the secrets to tuning up a Japanese Hand Plane (Kanna) We will start with conditioning the Body of the Plane (DAI) to stabilize movement. Proper sharpening and grinding of the blade and chip breaker will be discussed and demonstrated. Custom fitting the blade to the Dai and conditioning the sole. We will...

In this class, John will explain and demonstrate safe spindle turning techniques for turning a bud vase or a carvers mallet, an essential tool for anyone wishing to sculpt wood or make hand made joinery. Objective Through hands-on learning students will gain experience and confidence using our new Laguna mini lathes. You will develop an understanding...


Thread the rods through one of the legs, then set the leg flat on the table. Insert dowels into the dowel holes. Place the matching stretchers into place. Put dowels into the dowel holes at the top end of the stretchers. Place the other leg onto the threaded rod and settle it down onto the dowels. You'll probably have another opportunity to whack away with your rubber mallet.
Anyway, I'd like to know if I'll be able to keep (EDIT: and use) all my tools out there (current and planned) without having the shed become a rust-bucket for the tools and machinery inside. I'll have a 10" contractor's saw out there along with a drill press, a sanding belt, a router & router table, and lots and lots of old tools that I inherited from my Granddad years ago. I live in the Seattle area, so it rains A LOT. But I'm hoping that with the proper ventilation I can keep the tools in the shed dry.
×