I marked the holes by putting a dowel center in the end of a long piece of 1" dowel. Run it through the holes in the base plate, and bang on its end with a mallet. Rotate it a bit and bang it again, and repeat. Odds are the dowel center won't be precisely in the center of the dowel, so you'll be making a small ring of marks. The center of the hole is, of course, the center of that ring.
I had a similar experience with running electrical power to a shed. It turned out that I could build a 12x12 shed without a building permit as long as I did not run utilities, but getting a permit opened a whole new set of requirements that forbid me from having a shed at all. And when the nosey old woman next to me kept calling the building inspector on me, it was suggested that I could run an extension cord out to the shed anytime I wanted as long as it wasn’t fastened in a permanent manner.
In terms of size, this bench is another Sjobergs that is a bit on the small side, though it is actually far more squared than some others. While its length is a bit disappointing at 54″, the width is over 24″ wide which does provide for more diverse projects. Even better, this product still features the incredibly 500-pound weight capacity and continues the Sjobergs trend of avoiding joints that are not as durable as they otherwise could be.
After you have all the holes clean, set things up for your glue-up. You want everything on-hand before you start - drill, driver bit, glue, roller or whatever you're going to spread the glue with, and four clamps for the corners. You'll need a flat surface to do the glue-up on - I used my hollow core door on top my bench base - and another somewhat-flat surface to put the other panel on. My folding table was still holding my oak countertop, which makes a great flat surface, but I want to make sure I didn't drip glue on it so I covered it with some painters plastic that was left over from the last bedroom we painted.
Woodworking has a rich place in the history of human civilization. Used for thousands of centuries, it provided early cultures a way to construct shelters, furniture, boats, and more; in doing so, it made life easier and ultimately allowed a society to advance. The art of woodworking continues today, having survived a myriad of design aesthetics (including the not-so-wood-friendly Memphis Design). To pay homage to this ancient craft, one Instagram account called @wooodworking features pieces from different artists and artisans around the world.
Had a great experience at the shop! My schedule is hectic and unfortunately can't make the classes, but I did do a private lesson with Bob.  In one afternoon, we created two cutting boards.  Bob was very detailed with breaking down the process and using the machines.  Honestly didn't expect to make two cutting boards but Bob was proficient with time.  I got really comfortable using the machines especially the table saw.  I learned how to use the planer, jointer, miter saw, table saw, drill press, router, disk sander, and random orbital sander.  Really recommend folks that are interested in woodworking with little to no experience to take the Safety Orientation and the Cutting Board class or private lessons.  Looking forward to my next project at the shop!

A woodworking school teaching furniture making techniques located in Pennsylvania. Beginner through advanced students will learn solid wood furniture construction using traditional and modern techniques. The classes emphasize wood movement, practical methods, efficiency (with machines and hand tools), design, milling, joinery, finishing, and safety. Woodworking and furniture making courses are offered to aspiring crafts men and women throughout the country.
While $115 may seem expensive, try accurately boring a grid of 20mm holes on 96mm centers in 3/4 MDF. I have for a table for our retirement community shop - - its a pita. Plus the MFT material seems denser and more water resistant than garden-variety MDF. And the single-thickness has proven sufficient the last several years on my original 1080s. Still dead flat.
There are a number of tricks to using a router. First, the bit spins in a clockwise direction, as you look down at the router from the top. This means that when you cut with the router from left to right, the bit will tend to pull the router away from you, and when you route from right to left, the router will pull towards you. So, if you're hooking the edge guide along the near side of the board, route from left to right, and when you're hooking it along the far side of the board, route from right to left. Second, always test the position of your bit on scrap material. Your odds of getting it exactly right by eye are nil. Third, don't cut more than 1/4" deep on a single pass. We want a 3/8" deep grove, so make your first pass at 3/16", or thereabouts, and make a second pass to reach the full depth.
Laney College is located in Oakland near the San Francisco Bay and currently enrolls around 12,000 students. The Wood Technology Department offers 1- and 2-year certificate programs in wood technology, computer-aided drafting and design, as well as an apprenticeship program and carpentry courses. Students have access to eight faculty members and a variety of woodworking machinery and equipment, including a lathe.
This is one of those things that you never know you need unless you have one. This amazing wooden sofa sleeve works perfectly on either or both sides of a sofa set. It gives your sofa a nice look. The sleeve can also be modified to include a cup holder, mobile holder, etc. You can easily find this item on any online furniture store, but an even better idea is to build one. This way, you can make a sofa sleeve design that you actually like and make space for cup and other things.
I made a template by scribing two adjoining squares on a piece of MDF, using compass and straightedge, then marking each corner with a centerpunch, then drilling the points with a 1/16" bit. I find I'm always breaking small bits, so I picked up a couple of each size some months ago, and on looking I found I had three 1/16" bits, which worked fine for what I intended.

I don't see anywhere you mentioned the over all length of the bench top. A piece of 1 1/2" x 25" x 8' glued edge oak at Lumber Liquidators costs $192 including tax. Two piece is almost $400! Would that be better if I use two IKEA 1 1/4" x 25" x 74" solid Beech ($99 each plus tax) on top of a layer of 3/4" Birch plywood. That would be 3 1/4" over all.
Mine is similar but a bit more robust. The top is a sandwich, two 18mm sheets of WBP ply with an 18mm mdf filling. The legs are mortise and tenoned together, the ends glued and pegged, the stretchers are joined with long bolts so it comes apart. I stiffened it by adding a very closely fitted cabinet underneath (it had to go in dead square) and it is now absolutely rock solid.
This is technically a vanity factor, though the ability to store tools and other supplies at quick reach can be a time and energy saver. At the least, you will want a bench that comes with a shelf underneath. This will allow the storage of larger items that can otherwise be difficult to find a place for. Drawers are the other popular storage for benches and can make retrieving tools much easier – just make sure the inside of the drawer is lined with felt or the wood may prematurely dull your tools.

Cerritos College Woodworking, one of the finest woodworking schools in Southern California, offers classes in furniture making, cabinetmaking, CNC woodworking, and related topics.  Cerritos is the school for you, whether your goal is to acquire new knowledge, gain confidence in or improve your skills, enter the field of professional woodworking, or develop a rewarding hobby.
In terms of size, this bench is another Sjobergs that is a bit on the small side, though it is actually far more squared than some others. While its length is a bit disappointing at 54″, the width is over 24″ wide which does provide for more diverse projects. Even better, this product still features the incredibly 500-pound weight capacity and continues the Sjobergs trend of avoiding joints that are not as durable as they otherwise could be.
Lay a leg flat on your work surface, with the countersink side of the thru-holes down. Stick a piece of threaded rod in each hole. Take a stretcher that is marked to have one end adjoin the top of this leg, stick a dowel center in its dowel hole, line it up against the leg, using the threaded rod for positioning, You want the top of the stretcher to be even with the top of the leg, or just slightly above it. Give the end of the stretcher a whack with your rubber mallet. This will leave a mark indicating where the matching dowel hole in the leg needs to be drilled. Repeat with the lower stretcher than adjoins this leg. Then repeat for the other leg that will form this trestle, and the other ends of the two stretchers.
We want to make these pieces square, and of identical length. Square is a matter of making sure the saw blade is square and that the cutting guide is square. The trick to getting the pieces of the same length is to clamp them together and to cut them all at once. For the 4x4's, that means making a rough cut in each first, so we have four pieces, each 3-4" longer than we need, from which we'll get our four legs.

Linseed oil sitting in a bowl, or spread on the surface of wood, is perfectly safe. But a linseed oil soaked rag provides a vastly increase surface area, so the oxidation happens faster, and the rag can provide insulation, trapping the heat. The increased temperature speeds up the oxidation even more, which raises the temperature even more, and the runaway feedback can quickly result in temperatures that will cause the rag to spontaneously burst into flame. This isn't one of those "do not drive car while sunscreen is in place" warnings. This is one of those "keep your finger off the trigger until you have the gun pointed at something you want to shoot" warnings. Rags soaked in linseed oil will catch fire, if you don't handle them properly, and they can do so far more quickly than you might think.


I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.
I'd decided on an oil-and-wax finish. Oil finishes are by no means the toughest. In fact, they're really rather pathetic, so far as protecting the wood goes. But they're easy to apply, and not even the toughest finish will stand up to the abuse that a workbench will suffer, so it's more important that it be easy to repair. Wax is usually used to add a high gloss. On a bench, it's there to keep glue from sticking.
In class, each student will build a detailed hall table that is complete with mortise and tenon joinery, biscuit, dowel, and floating joint construction.  The student project is presented with a variety of design options and formats as to meet the experience and comfort level of each student.  Depending on their experience and comfort level, students are encouraged to make a simplified version of the hall table or tackle a more sophisticated and complicated version of the same project. Your only limitation is the amount of material you receive in your lumber pack (~24 board feet).
While $115 may seem expensive, try accurately boring a grid of 20mm holes on 96mm centers in 3/4 MDF. I have for a table for our retirement community shop - - its a pita. Plus the MFT material seems denser and more water resistant than garden-variety MDF. And the single-thickness has proven sufficient the last several years on my original 1080s. Still dead flat.
Of course, few benches can be ideal, and this one does have some drawbacks. That being said, most of the disadvantages of this bench are minor annoyances rather than deal breakers. For instance, this bench does not include any kind of storage whatsoever. Though, it does have the option of adding numerous additional features like a storage area. Still, for the bench, you would expect a drawer at the very least, maybe a shelf below the main table area.
By following the Woodworking Course, Woodworking Classes or Start Your Own Woodworking Business Course, you eliminate mistakes most woodworkers make when working on their first project or starting their first woodworking business. Learn the importance of wood selection, joinery and tool purchases. You will understand how to start and make your new woodworking business successful.
If you're using drywall screws, you'll want to countersink the holes. Drywall screws are flat-head, and need a countersink to seat solidly. If you're using Kreg pocket screws, the way I did, you won't want to counter-sink the holes. Kreg screws are pan-head, and seat just fine against a flat surface. Both drywall screws and Kreg pocket screws are self-threading, so you don't need pilot holes in the second sheet of MDF.
Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.
TOH has showed you how to make a toy chest with your kids before, but if you don't feel like cutting the wood yourself, opt for a kit like the one for this beautiful cherry chest. The kit comes with pre-cut pieces and all the hardware you need. Like many toy chests out there, the closed lid can also function as a bench seat, and the hinges are designed to prevent little fingers from getting caught. This model is available in three different finishes.
The Handy Home Products Berkley 10 ft. x The Handy Home Products Berkley 10 ft. x 16 ft. Do-It-Yourself Wood Shed Kit Combines charming country style and outstanding performance for the ultimate powerhouse. Offering maximum storage this woodshed is the ideal solution to house all your outdoor tools and lawn gear. Featuring 2x4 wood framing it boasts a ...  More + Product Details Close
Get perfectly, consistently spaced and centered shelf-pin holes! Economical and practical, this jig can be used on assembled or unassembled cabinetry. Re-designed handle includes two storage compartments for self-centering bits! Ideal for adding shelves to new or existing cabinets. Drills holes either 1-7/16" or 2-1/2" from edge. Insert shelf pin in top or bottom position to extend jig for continuous drilling. Shelving Jigs measure 20" long Additional Self-Centering Bits available. 
The popular account showcases woodworking in a variety of ways. Many of the things they share are of artworks produced using its techniques—including My Modern Met favorite Gabriel Schama. Other posts highlight its practical applications in the form of furniture or flooring, while videos offer a look into the process and range from educational to oddly satisfying. Whether you’re a fan of woodworking or looking to try it yourself, @wooodworking will both mesmerize and inspire.

Require the woodworker to be able to read the plans and to transfer images and dimensions from the plan to the lumber. The wood has been planed and all glued panels are completed unless over 14 inches. If panel required is over 14 inches, one glue seam will be required. The woodworker needs to be able to do some cutting, jointing, assembling and finishing. White Kits do not require planing. White Kits supply all of the needed hand-selected dimensioned lumber, but woodworking knowledge and tools will be useful to complete the project successfully.


I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.


In this class, John will explain and demonstrate safe spindle turning techniques for turning a bud vase or a carvers mallet, an essential tool for anyone wishing to sculpt wood or make hand made joinery. Objective Through hands-on learning students will gain experience and confidence using our new Laguna mini lathes. You will develop an understanding...

Build a shed yourself and use it as "on the job training." Those straw built sheds are rinky dink. The people who throw them together are even more sketchy than the finished product. You will be tearing it apart and hauling it out within a few years. Or end up having to reinforce the building with more braces and another layer of flooring. Thats my 99 cents. Its not hard to build a shed especially one of that size. Cowboy up and give it a shot.
×