I decided to finish the top with a number of coats of Danish oil, followed by a coat of wax. I applied the first coat of oil in the usual manner, making sure to cover the edges, and down the holes. I applied a coat oil to the top side of the shelf, as well. Wipe it on, let it sit wet for half-an-hour, then rub it off. Wait a day or two, add a second coat, and then again for a third.


The front edge of a woodworker’s bench is usually lined with square holes positioned at regular intervals. These holes hold bench dogs and holdfast clamps in place for securing work pieces. Beneath the top of the bench, some cabinetmaker models feature single storage drawers, others several drawers and even cupboards incorporated into a case-like base.
Lay a leg flat on your work surface, with the countersink side of the thru-holes down. Stick a piece of threaded rod in each hole. Take a stretcher that is marked to have one end adjoin the top of this leg, stick a dowel center in its dowel hole, line it up against the leg, using the threaded rod for positioning, You want the top of the stretcher to be even with the top of the leg, or just slightly above it. Give the end of the stretcher a whack with your rubber mallet. This will leave a mark indicating where the matching dowel hole in the leg needs to be drilled. Repeat with the lower stretcher than adjoins this leg. Then repeat for the other leg that will form this trestle, and the other ends of the two stretchers.
This is my first post here but been lurking for a while. I am currently working in a 10x14 shed which has sufficed nicely until my recent purchase (sunday) of a new Craftsman table saw model OR35505. This I discovered ate a lot of space but with some reorganization and some good casters, it's going to work. I did add a window AC unit and will need to figure out some heat but hoping to have built a better shop with HVAC before it's too cold.
Permanent or Portable? This is a distinction that decides much about your bench choice: Is it to remain stationary or must it fold, roll, or otherwise make itself scarce between jobs? Large, heavy benches are more stable and, in general, more adaptable to different jobs (sometimes several at once). But the bigger the bench, the more hassle involved with stowing it.
My first shop was a 8 x 10 ft room, actually a bedroom, with 10 ft high ceilings in a older home in Chicago. I had a 10" Craftsman TS, drill press, 8 1/4" Skil saw which still works, some welding tanks, hand tools and... my bed was a loft across the 10 ft length 4 ft down from the ceiling with a ladder against the wall to get up. I was 16 yrs old then, now I am 66 yrs, have 2 shops with Craftsman power tools up stairs, and Grizzly tools ,a Powermatic 68, a MIG welder, and other tools on the ground floor. I've come a long way, You think? I remember making bases for sculptures called "plinths", my first commission, in the living room, 5 pieces rather large, several ft long and wide. The house was haunted, and my mom told the "spirit" to leave and go back downstairs. There was a cold draft and the straw chair would rustle with no one sitting in it. Wow, does that bring back memories from the '60's.
2 - use a plunge router with a bottom bearing cuter bit such as this from rockler: http://www.rockler.com/product.cfm?page=25160&site=ROCKLER .... I thought to use the short one as I plunge it directly downward in the centre of the hole until the bearing reaches within the tabletop hole. I suppose one could use a long one, but the stubbiness seemed more practical (the big bearing ensured accuracy?)
A woodworking school teaching furniture making techniques located in Pennsylvania. Beginner through advanced students will learn solid wood furniture construction using traditional and modern techniques. The classes emphasize wood movement, practical methods, efficiency (with machines and hand tools), design, milling, joinery, finishing, and safety. Woodworking and furniture making courses are offered to aspiring crafts men and women throughout the country.

You can buy sandpaper, glue, and other consumables from them for a nominal price. Their hand tools are propitiatory though so you would have to buy a specific kind of orbital sandpaper, for example. You couldn't just get generic. They are reasonably priced though. There is literally a coffee can with money in it and prices written on the boxes with these consumables. If you think you might burn through enough sand paper on something, check the brand and price shop.


A workbench needs to be heavy enough that it doesn't move under you while you're working, and stiff enough that it doesn't rack itself to pieces under the forces that will be placed upon it. It doesn't take many hours of planing a board or hammering a chisel for a worktable made of nailed 2x4s to come apart. Traditional bench designs use mortise-and-tenon joinery, which is strong and rigid, but not really suited for a novice woodworker who doesn't already have a bench.
With the top laying on the floor, bottom side up, the next step is to flip the base upside down, and attach it to the top. I followed Asa Christiana's design, in using s-clips. When I stopped by my local Woodcraft, though, they only had two packages of ten, so I didn't use as many as I would have, otherwise. For the top I put four on each side and two on each end. For the shelf I put three on each side and two on each end. If it turns out that I need more, I can always add more.
Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.
So far, I really like the space. I signed up for a 3 month stint and hopefully will have some things to show for it. For my background, I took shop for 3 years in high school. I've always enjoyed working with wood but never had the space for it. I'm not a master craftsman but there are some really talented people there creating some nice pieces. All levels are welcome here.
While a strict figure for the bench’s weight capacity is not available, a quick browse through their other stand and bench products shows a general weight capacity well above most other brands. As such, while we cannot say for certain that this bench provides the best weight capacity, it is more than likely that it the capacity is similar to the other products in the catalog.
Our Lexington model was designed to match many traditional New England homes, in Massachusetts and beyond. The steep pitch of the roof is built to withstand sometimes-punishing New England snow loads and complement today’s home design styles. Post Woodworking can match most vinyl siding colors, so that your shed color will coordinate with your home as well. And as is the case with all of our sheds, interior solar lighting is available to light up the night.
×