The Practical Woodworking course at the JD Lohr School of Woodworking is a complete and comprehensive woodworking course held in our shop on the 13-acre farm in southeastern PA. This is total immersion woodworking for ambitious, interested adults. With class size limited to 11 students and 3-4 instructors in each class, all needs of every student are met regardless of experience level. If you are self taught with no formal training as a woodworker, this course will quite literally change the way you work.
Drilling a precisely positioned, deep, wide hole isn't easy, without a drill press. So I bought a WolfCraft drill guide. After experimenting with it, and drilling some test holes, I build a jig around it. I screwed it to a scrap of MDF, and then drilled a carefully-centered 3/4" hole. The MDF can be clamped more easily than the base itself, and the 3/4" hole will keep a 3/4" Forstner bit drilling precisely where it is supposed to.
Cerritos College in Norwalk serves over 21,000 credit students each year with certificate and degree programs for recent high school graduates and adult learners. The Cerritos College Woodworking school is housed in 27,000 square-feet of space and is equipped with over 100 woodworking machines. Under the direction of 20 instructors, the school offers more than 50 classes in woodworking, including those in architectural millwork, cabinet and furniture making, routing and veneering.
Had a great experience at the shop! My schedule is hectic and unfortunately can't make the classes, but I did do a private lesson with Bob.  In one afternoon, we created two cutting boards.  Bob was very detailed with breaking down the process and using the machines.  Honestly didn't expect to make two cutting boards but Bob was proficient with time.  I got really comfortable using the machines especially the table saw.  I learned how to use the planer, jointer, miter saw, table saw, drill press, router, disk sander, and random orbital sander.  Really recommend folks that are interested in woodworking with little to no experience to take the Safety Orientation and the Cutting Board class or private lessons.  Looking forward to my next project at the shop!
The oldest woodworking shop in America has been discovered virtually untouched in Duxbury, Massachusetts. The extremely rare find reveals an 18th century joiner’s shop with the date ‘1789’ painted in the rafters. University of Delaware professor Ritchie Garrison came upon the historic structure on the site of a preschool, bringing several experts out to verify its age. Craftsmen used the shed to create intricate woodwork.
I like the idea of re-inventing the wheel. I choose to believe that while others may have considered these improvements, they just never got around to trying them out. Brain gets bored with status quo. So, I try to keep Brain happy with the occasional foray into uncharted territory. And I must say Brain has had some really good results. Thanks, in part, to you, and the Roy. You never know where a good idea might come from so I’ll check in once in a while. That and make sure to build it in Sketchup first.
The first time you try your hand at the ancient craft of woodworking, you want to do it right. Learn woodworking basics with hand tools to a professional standard on a weekend woodworking course at Rowden Atelier. Ed Wild runs weekend furniture building courses for everyone from beginners who want to have some fun experimenting behind the bench, to those who are looking to develop specific skills as a furniture maker. Classes include tool handling, box making, and basic veneering, but to a certain degree, you can tell us what you want to learn - these short woodworking courses are partly bespoke.
I’ve seen antique cabinetmakers’ benches that are sixteen and seventeen feet long, more than three feet wide, and supported by a dozen drawers and doors—and that weigh as much as a felled oak tree. In contrast, jewelers’ cabinets seem to be on a dollhouse scale, with tiny tools to match. For most of us, however, space limitations preclude the biggest, and the smallest are just not big enough.
Not sure about Midwest but I have a 24 x 14 Game rm attached to my shop and I put a small window unit/heat pump in the wall. It stays comfortable all year round. It get really hot here and we had a several day in the 20's this winter but it's insulated well. That might not be as cold or as hot as in some places but the unit I haze does not run that often and has a low cost rating. I'm planning on putting a larger unit in the shop area even though I do like to work with the garage door open. The door is insulated so I can run A/c in there. Just my .02.
For a fun and comprehensive learning experience, take an online woodworking class in the WWGOA Academy. You’ll learn in-depth woodworking how-to, get bonus material, and enjoy custom benefits for class participants. You’ll never lose access to your Class; no strings attached! Check back often – as we’re adding new online woodworking classes regularly.
The holes we want to mark are the holes through which the threaded rod connecting the two legs will run. This threaded rod will run through the 3/8" groove along the bottom of the short stretchers,. The hole for the upper stretcher has to be positioned so that when the rod is running through this groove, the top of the short stretcher is even with the top of the legs. The most precise way I've found for marking the position of this hole is to use a dowel center. Fit the dowel center into the bottom groove, line up the stretcher, and bang on the end with a rubber mallet. The dowel center will leave a mark indicating the center of the hole.
You're not the first person to say this! I'm half inclined to use the Lowes shed as a starting point for my own design. But I do think I'd feel better if I could work as an "aprentice" next to an "old master". Someone at work is going to put me in touch with a guy who builds sheds for a living, and apparently he's competitive with the prices @ Lowes and HD. The Lowes shed comes with a "Handman Package" that I don't want but would end up paying for, anyway. The "workbenches" were laughably flimsy.

Every single person in the class was a novice when they walked in. We all made mistakes at some point, yet none of us really ever felt bad about these hiccups. Inevitably, Bob turned these mistakes into problem-solving opportunities where we could explore new ideas. So what if one morning I skipped coffee and accidentally spent 10 minutes drilling random-ass, pointless domino mortises in the middle of my bench legs? 4 dominos, some sawdust and glue, a little bit of sawing and sanding-- I've got four new inlays on my legs and nobody's the wiser. Not only do I now know how to roll with the punches when building something, but I've got a bench that's uniquely mine AND I don't feel like an idiot. And that last part is a serious feat.
Requirements and electives for the certificate and degree programs in cabinet and fine woodworking include an advanced cabinetry lab and a course in Euro-style hardware. Students in both the construction and cabinet programs can also learn about business contracts, receive training in computer technology and participate in a cooperative work experience.
The edges of MDF are fragile, easily crushed or torn. MDF is also notorious for absorbing water through these edges, causing the panels to swell. In Sam Allen's original design, he edged the MDF with 1/4" hardboard. This edging is one of the complexities that Asa Christiana left out in his simplified design. I think this was a mistake. MDF really needs some sort of protection, especially on the edges.
At the age of 9, Mark’s interest in woodworking began, which led him to begin an apprenticeship with Homestead Heritage Furniture at the age of 17. In his own shop he has built many pieces of furniture from small dovetail boxes to large 10′ round conference tables. Most of his work has been for clients who have ordered custom pieces for their homes and offices. Mark has been building custom furniture for the last 20 years and is now the manager of the Heritage Furniture business. Mark enjoys making hand tools and jigs that can simplify the building process. He has taught children how to shape simple utensils like wooden spoons and cutting boards as well as other larger projects. “Seeing the young grow to maturity in their craft is what I appreciate.”
Next is the shelf. Start with the 24x48" piece of MDF. Clamp this on top of the base, and pencil in the outside of the stretchers and the inside angle of the legs. Flip it over, pull out your trusty cutting guide, and cut it to width and to length. Cutting out the angles is simple, with a jig saw. It's not much work with a hand saw. If you took enough care with supporting blocks and stops, you could probably do it with a circular saw. Since I did have a jig saw, I used it.

One quality about this bench that is definitely lacking is space – both tabletop and storage. The Olympia Tools does provide an adequate shelf, but it does not come with any drawers, nor does it offer the option of adding them later. The table top is the smallest we saw at 50” long and 2’ wide, though the width is actually better than most of the other table we reviewed. Still, a significant chunk of that width is occupied by a trough. This trough is designed to hold smaller workpieces to keep them from falling or getting knocked over, but it removes about 6” of width from the tabletop.
All glue & stain benches are made using a solid maple frame for lasting durability and strength. Side Clamp Benches are made specifically for bar clamps, and are used for gluing projects or clamp storage. Benches feature an open top with 17 sets of 3/4"W grooves that accept bar clamps measuring 3’ and over. Lower center rail is adaptable for storage of hand screws and C-clamps. Side clamp benches are available with or without a drip pan. Glue & Stain Benches are made with a 1-1/4” plywood top covered with heavy-coated galvanized steel. Bottom shelf has a 4” rear retaining lip. Glue and stain benches are available with or without casters. Limited Lifetime Warranty.
We have more than sixty years of excellence (1956-present) with an annual enrollment of more than 1,000 students in over 35 different classes.  The Palomar College Cabinet and Furniture Technology program offers the most comprehensive woodworking career curriculum in the nation. Utilizing three fully-equipped shops, our 2 full-time and 20 part-time instructors provide a breadth of courses and depth of expertise impossible to obtain in smaller programs.
Then I flipped the top and the base, lied up the base in the proper location relative to the top, I then positioned the front vise and the support MDF for the end vise, and marked the locations of the bolt holes. Then I flipped the base right side up, drilled small pilot holes from the bottom side where I had marked the locations, and then drilled shallow countersink holes from each side, then a through hole that matched the bolts. Finally I tried out the bolts and washers, and deepened the countersinks until the heads of the bolts were just below flush.
This is my first post here but been lurking for a while. I am currently working in a 10x14 shed which has sufficed nicely until my recent purchase (sunday) of a new Craftsman table saw model OR35505. This I discovered ate a lot of space but with some reorganization and some good casters, it's going to work. I did add a window AC unit and will need to figure out some heat but hoping to have built a better shop with HVAC before it's too cold.
Our stationary equipment runs the complete range from heavy-duty industrial machines, to inexpensive home shop type of tooling so that each student can compare and contrast the range and versatility of equipment at a wide variety of price points.  We spend time on what makes a good machine good, an adequate one adequate, and a lousy machine worthless. We have no commercial sponsors and will share our opinions based on our experiences regarding the quality of one manufacturer over another.  There is no better place to kick the tires on a variety of equipment than at our shop.     
Every single person in the class was a novice when they walked in. We all made mistakes at some point, yet none of us really ever felt bad about these hiccups. Inevitably, Bob turned these mistakes into problem-solving opportunities where we could explore new ideas. So what if one morning I skipped coffee and accidentally spent 10 minutes drilling random-ass, pointless domino mortises in the middle of my bench legs? 4 dominos, some sawdust and glue, a little bit of sawing and sanding-- I've got four new inlays on my legs and nobody's the wiser. Not only do I now know how to roll with the punches when building something, but I've got a bench that's uniquely mine AND I don't feel like an idiot. And that last part is a serious feat.
At Costco, we understand that when you’re looking for a shed or barn, you’re not just looking for a space to store your tools, you’re looking for a structure that’s reliable, sturdy, and weatherproof. This kind of quality assurance is especially important when your shed or barn isn’t just a toolshed, but a place for storing your memories or working on projects. At Costco.com, you’ll find sheds and barns of all shapes, sizes, and materials. Shop by brand, color, or features, and rest assured, knowing that whatever structure you choose, you’re getting it at the best possible price!
This instructable shows how to build, with basic tools and readily-available lumber, a bench that provides most of the function of a traditional woodworker's workbench. I began with a design by Asa Christiana that was featured in the second season of finewoodworking.com's video series Getting Started in Woodworking. The project plans are available on their website.
I’ve built workbenches with more than 100 students. In every class, there’s one guy who wants to put a vise on every corner of the bench. Not because it’s a partner’s bench for two people. Just because he wants it that way. While I support your freedom to choose, I also don’t want to spend two weeks installing complex tail-vise hardware on your bench when we could be building furniture instead.
Our instructors work out of a 27,000 square-foot facility, where over 100 stationary and portable woodworking machines are available. We emphasize hands-on training and real-world experience, and all classes are project-focused. Over forty different classes cover topics including faceframe and frameless cabinet construction, CNC woodworking, architectural millwork, table and casegood construction, hand tools, woodturning, and veneering.

Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
The course successfully meets the needs of multiple experience levels in a safe, well equipped, spacious, congenial, and educational environment. All instruction and lab experience is under the personal direction of master woodworkers as well as one or two additional experienced woodworkers/teacher assistants who are on hand during all lab hours providing roughly a three-to-one student-to-instructor ratio. Intermediate to more advanced students should not be put off by the fact that beginners are also included in this course.  Check out some of the work done by our alumni in the Alumni Furniture Gallery to get an idea of what our students are capable of.

I mocked up the two scenarios, and determined that with the plate inside the stretcher the vise would have a reach of 8 inches, and with it outside the stretcher it would have a reach of 9 inches. I decided that 8 inches was enough, and that the extra inch wasn't worth the extra effort. With the end vise mounted like this, the right edge of the top would have no overhang.

A better solution would have been to route a rabbet into the side, so that the added strip always had thickness. The way I did it means that the strip I glued in is very narrow, and hence very weak, at a certain point. In this case, that's not a problem, because it's going to be sitting under the countertop layer. I also noticed that because I had only clamped the strip down, and not into the edge, there was a noticeable glue gap where the strip butted up against the MDF. Again, in this application it isn't visible. But if I was doing something like this on the top of a table, I'd make sure to cut a clean rabbet, and to clamp both down and in.
The Handy Home Products Berkley 10 ft. x The Handy Home Products Berkley 10 ft. x 10 ft. Wood Storage Building Kit is made with factory-primed SmartSide siding to resist fungal decay and wood-destroying insects. The Berkley’s gambrel style roof provides plenty of height to add a loft for extra storage space. The 6 ft. high side walls ...  More + Product Details Close
I can't recommend this place highly enough. As someone who wants to test the waters in the hobby of woodworking this is the perfect place. They have all of the tools you need to complete your project, and they are great with helping beginners. I began as a skeptical customer but the staff was super ready and willing to make sure we could rectify a misunderstanding.
This Vermont Farmhouse by Real Good Toys is as pretty as the real thing. And if the seven-room home isn't big enough for the serial renovator in your kid, the site also sells additions that add two rooms to either end of the house. Just like the homes old-house lovers hope to own, this farmhouse comes with real wood shingles, wood floors, interior crown molding and a spacious porch.
Require the woodworker to be able to read the plans and to transfer images and dimensions from the plan to the lumber. The wood has been planed and all glued panels are completed unless over 14 inches. If panel required is over 14 inches, one glue seam will be required. The woodworker needs to be able to do some cutting, jointing, assembling and finishing. White Kits do not require planing. White Kits supply all of the needed hand-selected dimensioned lumber, but woodworking knowledge and tools will be useful to complete the project successfully.
It doesn't get much better than a day at the woodshop! I've taken several classes from cutting boards to turning vases. It is always fun and informative! All of the machines are top notch and the instructors are great! I've toyed with the idea of a membership but I think I'll take a couple more classes before doing so! I can't wait to see the new location! :)
While $115 may seem expensive, try accurately boring a grid of 20mm holes on 96mm centers in 3/4 MDF. I have for a table for our retirement community shop - - its a pita. Plus the MFT material seems denser and more water resistant than garden-variety MDF. And the single-thickness has proven sufficient the last several years on my original 1080s. Still dead flat.

The end vise will have both jaws made out of 1-1/2" thick oak. The front vise has its moving jaw made of 1-1/2" oak, but uses the edge of the bench as its stationary jaw. So while for the end vise, if we mount it lower, we can make both the jaws deeper to compensate, for the front vise we cannot, so we want it mounted as close to the edge of the bench as possible.

This particular tray is made using reclaimed barn wood but the author of the project Beyond The Picket Fence surprised everyone with one fact: reclaimed barn wood has often some areas turned pink due to cow urine. If you check the project more closely, you’ll also notice some areas of the tray being almost bright pink. That’s something you don’t see every day!
I clamped the top to the side of the base, as I had done before, so that the edge with the knot would be easy to work with. I mixed up some ordinary five-minute epoxy and added just a touch of black epoxy pigment. I applied this freely. After about twenty minutes I checked on it and found that in the deepest spot the void wasn't entirely filled, so I mixed up another batch and added more. After that had cured for a bit I eased the top to the floor and applied a coat of oil to the bottom side. I planned on attaching the base to the top the next day, and I wanted the bottom side oiled to keep it from absorbing moisture.

The book is well written and easy to read. The illustrations, I'm sure were excellent in 1914 and, are still adequite now. Most of the designs seemed repetitive, though. I wish more attention had been given to lashing materials. If you are looking for that you will find almost none here. The book was fun to read and provided enough inspiration to make my brother and me attempt a large hut.
×