Timberframing is a traditional technique for building large and small structures using only wooden joinery. Prized for its structural integrity and beauty, as well as reliance on hand skills, timberframing is regaining popularity in modern applications. We will start with an overview of the different styles and aesthetics involved, and move into the specific tools that are used to lay out and cut the strong joints. Each student gets guided practice time making sample joints. We will all work together to make a small structure that can be raised on the final day of class.
Still, one of the best features about this woodworking bench has to be its vices. First off, the Sjobergs provides two vices both as sturdily constructed as the bench itself. The same hardware that fastens the bench works to ensure the vices are just as strong. The next main benefit on the vices in the inclusion of multiple positions – four in total – for the vices to go. This allows you to mix and match to suit your needs and allows the table to be used just as easily by right-handed and left-handed users.
The Classic Workbench is simple to use. The leg vise is used primarily for working the edges of boards and the ends of narrower boards. This is self explanatory. To work the faces of boards along the grain, tap up the planing stop (don’t make it any higher than necessary) and butt the end of the board into the teeth of the stop. With the right technique you can plane across wide boards without repositioning the board. You usually don’t need to tap the opposite end of the board to engage it with the stop, but in some cases, especially with rougher stock, you may need to give a tap with your mallet. Working the faces of a stack of boards is extremely quick with the planing stop since you don’t have to open and close a vise constantly. To work across the face of a board, make yourself a doe’s foot and position it at the back corner of the board, holding it down with a holdfast. The doe’s foot is simply a piece of wood with a V-shaped notch cut into one end. The bottomsurface of the doe’s foot can be lined with sandpaper or Crubber to help it stay put on the bench top. To work long boards, fasten a batten to the right leg with a holdfast and use that to support the end of the long board. We’ve found that a deadman is not necessary for the majority of work, especially on a bench of this length. For working the ends of smaller boards the leg vise can be used, but for precision work like dovetailing, we use and recommend our Moxon Vise.
An excellent introduction to woodworking is to use crates as your main material. The boxes are already formed, which means less assembly work for you—yet it looks impressive once your project is altogether. With this crate coffee table, you still get to practice your skills adding the casters and the center box. Finish with a little stain, and this table is ready to roll. You can find the full tutorial at DIY Vintage Chic.
Something like this really does look like it would be a fun project. I guess I need to go out to the yard and use some stakes and brightly colored taped to mark off some different dimensions (12x8, 12x10, 12x12, etc.) to figure out just how big I can make this thing. If I'm building it myself, it'll be easy to keep the height right at the 9 foot limit.
A shed is a great project to earn your sawdust legs on. It is just some very basic carpentry skills. You could build the whole thing with a circular saw, hammer, utility knife, pencil, and tape rule. Find a friend or relative that has some decent skills to help. You could do it in a weekend. Keep the size on a four foot increment to minimize wastee. I would recommend a 12 x 12 or a 12 x 16 if you can. If you don't want to cut any rafters (which is really a simple process), you can order small triangle shaped trusses for the roof from your local lumberyard. If you are using T1-11 for the sides, get the real plywood based stuff, no waferboard. Same thing for the floor, use plywood (treated if you like). Cedar for the trim, not pine. The visqueen underneath is a good idea. Insulate the walls inside to help temper temperature swings. Build overhanges into the roof all the way around, 12" is nice. These really are a fun project. You can add a small window with a flower box underneath to make it look a little homey too.
You can transfer a graphic on any wood piece of your choice, including a frame, top of a table, etc. The surface should be clean and big enough for the graphic paper. I am also sharing a video tutorial here that explains in detail the process of transferring any graphic to a wooden surface using a freezer paper. Just gather the items you need and follow this video to carve your favorite designs on your favorite wood items.
With my second attempt at edge guides, I made the other rough-cut. On this, the edge guide worked fine, but the end of the cuts revealed that the saw blade wasn't quite square. So I adjusted the blade, clamped all four legs together, and made what would be the first final cut, if it came out clean enough. It didn't. I'd let the saw drift a bit away from the guide edge. So I adjusted the saw, moving the guide back half an inch, and tried again. the rough-cut parts were a couple of inches longer than they needed to be, so I had room to work with,. It's only the final cut at the other end that you only have one chance at.
For the router you'll need a a 3/8" straight bit, an edge guide, 1/4"- and 1/8"-radius roundover bits, and a flush-trim bit with at least a 1-1/2" cutting length. Bits of this size are available only for a 1/2" collet. Some routers are capable of using multiple collet sizes. I was fool enough to buy a router that only had a 1/4" collet. More on that, later.
You may even want to put yourself in the picture. If your workshop space already exists, find a large piece of cardboard, wallboard, or plywood that’s about the size of the workbench top you envision. Find a couple of stools or chairs, perhaps a few books, and turn them into stanchions to support the “benchtop.” Is it too big for the space? Is it large enough for the tasks you envision will be performed upon it?
I thought my first wood working bench was great.A heavy c channel metal frame with a recycled maple floor top with a guick release 7 in vice on the side.It is about 40in by 54in and can hold a hemi no problem. I waxed the top till it was nice and resistant to whatever was dripped on it. Only problem is I was thinking like a gear head not a wood worked.Work piece would slide and no decent clamping on the sides. I figured if I wanted to get somewhat serious about this woodworking thing I needed a real bench not a table with a vice. I read the books and with so many choices I chose a Roubo split top from Benchcrafted it would let me use it for both power and hand tools. I just finished it a week ago and it is nice not to have to chase my work across the bench. I couldn’t find a clear answer for a top coat for the bench I chose to leave the soft maple nude. So I guess I have a bench tbat has a lack of modesty.
This class is open to novice woodworkers and to more experienced woodworkers who would like to broaden (or simplify) their approach to woodworking. What do we mean by novice? We think it means you are a person who has decided to commit to learning new skills; to growing a passion for the craft of working with wood; and has a strong sense of the limitations of your own knowledge.
The bench I will be describing differs from both of these in a couple of areas, the most significant of which is the top. Allen's top was made from three layers of 3/4" medium density fiberboard (MDF), topped and edged with 1/4" hardboard. Christiana's top was just two layers of 3/4" MDF. My top is two layers of 3/4" MDF edged with 1/2" oak and topped by a 1-1/2" thick edge-glued oak Ikea countertop. My top is more expensive in both time and money than either Christiana's or Allen's. If you're looking to build something fast and cheap, I'd recommend Allen's approach over Christiana's. The hardboard significantly increases the durability of the top.
Build on the skills you developed in Woodworking I through the construction of a small cabinet. Woodworking II introduces students to miter and dado joints, hardware installation, and re-sawing on the bandsaw. Please bring a sketch for a small cabinet you would like to build to the first class. NOTE: Students are responsible for their own materials in this class.
The Cape Ann Shed was designed with coastal New England in mind. So yard work may feel like you’re actually on vacation. From Cape Cod to the beaches of Maine, you will find a Post Woodworking Cape Ann shed adorning the yards of thousands of homes. It’s a popular style with our customers – whether they make their home by street or by sea. An affordable choice for an outdoor structure, the Cape Ann brings functional elements with nautical appeal.