The projects in this course follow a natural progression of skills, techniques and tools. Some of the early student-made tools are, in fact, used to help make the next tool or bench fixture in the series. You are supported in the building of these projects with step-by-step outlines, knock-down examples and continuing, one-on-one consultations with the faculty. Periodic evaluations of your progress with a specific faculty-mentor help keep you on track.
This is one of those things that you never know you need unless you have one. This amazing wooden sofa sleeve works perfectly on either or both sides of a sofa set. It gives your sofa a nice look. The sleeve can also be modified to include a cup holder, mobile holder, etc. You can easily find this item on any online furniture store, but an even better idea is to build one. This way, you can make a sofa sleeve design that you actually like and make space for cup and other things.
After I left the magazine for a new job, I did all of my woodworking in my small two-car garage, but it was a struggle. Power, lighting, and temperature control were limited. And because I shared space with our cars I was always moving machines around, often while in the middle of a project. On top of that, my tool and machine collection had long since eclipsed the space. For all these reasons, fixing up the garage wasn’t an option. My finished basement is a family room, so it was out, too. An addition to the home or a stand-alone building would have been too expensive. I had to find a better path to a shop.
They immediately tried 2 of the projects, and first found that the instructions were a little vague (so many similar sized/shaped pieces - it was difficult to sort them!). The glue included in the kit had separated, and was not usable - but basic wood glue, which we had on hand, worked just fine. The projects turned out great, and, the time spent working on them was priceless!

Remember those fire safety tips you used to get in grade school, about the dangers of oily rags? It was linseed oil they were talking about. All oily rags are dangerously flammable. Linseed oil will self-combust. Linseed oil doesn't evaporate, it oxidizes. The oxidization generates heat, and the increased temperature increases the rate of oxidation.
The top is supported by the top ends of the legs and the top sides of the top stretchers. Stand your legs on end on a flat surface (like my door) and see if they wobble. If you have an end that isn't quite stable, use it as a foot, where the leveler will make it's flaws unimportant. Check the top edge of each stretcher for straightness. If one has a bit of a bow, use it for a lower stretcher. It's less critical that the shelf be well supported along its length.

I never, ever, ever bother to write these things. But, I am so incredibly impressed with this product, that I feel compelled to. My six year old daughter LOVES IT, as does my almost four year old daughter. The hammer is just the right size, and it comes with enough pre-cut (good quality) wood for many projects. So far, they have made a house, car, and a plane-- all of which are far more aesthetically pleasing (to me, as a mom) than the plethora of junky plastic toys that seem to fill our home. We've used these projects both as math lessons (measuring the wood, counting the nails needed, learning about angles, reviewing shapes) and during arts & crafts time; but, with just a little creativity, they could be incorporated into just about any learning subject. For the amount of enjoyment we have received, thus far, this product is already worth the money spent, and we have several more projects to go! We will be buying another for little sister's upcoming birthday, most definitely.


Before you start cutting or drilling the pieces that will make up the top, determine the layout of the top. This should include the dimensions of the MDF, the dimensions of the edging, the locations of the vises, and of the screws or bolts that will support the vises, and of all of the benchdog holes and of all of the drywall screws you will use to laminate the panels,
Learn woodworking from a home computer, tablet, or smartphone. Woodworking video lectures can be followed sequentially or in any order. The lectures can be repeated to reinforce what you have learned. Flexibility in learning allows you to speed your woodworking knowledge. Learning the essentials of woodworking accelerate your learning curve to become a woodworker
The last thing is to semi-permanently attach the bolts for the vises. Given the amount of work necessary to get to the bolt heads, once the top is joined, I had intended to tighten them up so they wouldn't spin, and lock them that way with blue Loctite. (That's the strongest non-permanent grade.) That didn't work. What I found was that the bottoms of the countersinks weren't quite flat, and when I tightened the nuts down that far, the ends of the bolts would be pulled far enough out of alignment that the vise bases would no longer fit. In order for the vises to fit over the bolts, I had to leave the nuts loose enough that the bolts had a bit of wiggle - which meant that they were almost loose enough for the bolts to spin. So I put Loctite on the nuts, to keep them from unscrewing, and filled the countersinks with Liquid Nails, in hopes of keeping the bolts from spinning. I considered using epoxy, or a metal-epoxy mix like JB Weld, but I didn't have enough of either on hand. It seems to be working for now, though the real test won't be until I have to take the vises off.
This trade and technical college currently serves over 15,500 credit students from its campus in downtown Los Angeles. Through the Construction, Design and Manufacturing Department, full-time students can enroll in a daytime certificate or an Associate of Science program in cabinet and millwork. Evening programs for current craftspeople include a certificate program in construction technologies and an Associate of Arts in cabinetmaking and millwork that provide students with the skills they need to work in construction or manufacturing.

I built my first platform bed by following the steps mentioned in the tutorial and the end result was everything I expected. It was as beautiful as comfortable and strong. It only cost me around $60 to build this one from the scratch. And if I can build it, anyone can. What you need is a little bit of woodworking experience and a lot of confidence. Collect the items as suggested in the video and start working now.
The 84-906 fits this bill perfectly as the table offers all of the qualities and features that you would expect but does not truly blow you away with any of them. For instance, this bench is made out of rubberwood. This wood is decent in that it provides the strength you want, but it is also extremely porous and rough-grained. The porous nature would generally make it susceptible to rotting and staining, though the bench has been lacquered. The rough grain will potentially cause tools to dull over time if you do not regularly relacquer it.
The base needs to be as wide as the sum of width of the guide strip and the distance from the edge of the shoe, plus a bit extra, With my saw, the overhang is 3-1/2", so I made my guide strip 5-1/2" wide. The distance between from the edge of the shoe to the blade is about 4-1/2", so the base needs to be at least 10" wide. Since I was working with a 24" wide sheet, I just sliced it down the middle.

Every piece meets the highest grading standards for Every piece meets the highest grading standards for strength and appearance. This lumber is for a wide range of uses from framing of houses to basic interior finishing applications. Boards can also be used for carpentry hobbies furniture shelving and general finish work. This lumber can also be used in ...  More + Product Details Close
With the Grain: A Craftsman’s Guide to Understanding Wood by Christian Becksvoort. A little knowledge about trees goes a long way toward improving your woodworking. You don’t need a degree in dendrology to build a desk. But you do need intimate knowledge of how our raw material grows and – more importantly – how it responds to its environment after it has been cut and dried.
The decision to be made with respect to the end vise is whether the support plate should be mounted to on the inside or on the outside of the stretcher. Mounting the plate on the inside of the stretcher reduces the reach of the vise - it can't open as far, because the support plate is back from the edge by a couple of inches. But mounting the plate on the outside of the stretcher means that we need to add some support structure for the inner jaw of the vise, which the legs would have provided if we'd mounted the plate on the inside.
I'd decided on an oil-and-wax finish. Oil finishes are by no means the toughest. In fact, they're really rather pathetic, so far as protecting the wood goes. But they're easy to apply, and not even the toughest finish will stand up to the abuse that a workbench will suffer, so it's more important that it be easy to repair. Wax is usually used to add a high gloss. On a bench, it's there to keep glue from sticking.
When the top is done, we want the edged MDF and the oak countertop to have exactly the same dimensions, and for their width to exactly match the width of the base.I could see three ways of doing this: 1, join the MDF to the countertop and use my belt sander to sand down their joined edges to match the base; 2, join the MDF to the countertop and use a hand plane to plane down their joined edges to match the base; or 3, use a flush-trim bit against a straight edge to route the MDF to the width of the base, then join the MDF to the countertop and use the flush-trim bit to route the countertop to match the MDF.
I recently came across this beautiful wooden swing set, which was made in the shape of a boat. Cool, isn’t it? The very first look was enough for me to start loving it. Although I haven’t yet tried building one myself, I am definitely going to. Later I realized that you can also build a baby cradle with the same idea. After all, what can be more calming than the tender rocking of a boat? This swing set will surely help your child get more gentle sleep.
Tuition for Practical Woodworking is $1200 for six 8-hour days of instruction and active woodworking. Lumber is provided and costs an additional $85. We provide most tools, students are only required to bring a tape measure, sharpie, pencil, and eye protection (sanders and sandpaper are encouraged if you've got them).  Visit our Course Project page to see the table we make!
I’ve seen antique cabinetmakers’ benches that are sixteen and seventeen feet long, more than three feet wide, and supported by a dozen drawers and doors—and that weigh as much as a felled oak tree. In contrast, jewelers’ cabinets seem to be on a dollhouse scale, with tiny tools to match. For most of us, however, space limitations preclude the biggest, and the smallest are just not big enough.
This is for the serious amongst you. Those of you who are ready to make a change in your life. To really surround themselves with woodworkers and furniture making for a whole year. Not only do you get to learn some great traditional skills but also drawing, the beginnings of design and how to run a woodworking business successfully. This intense workshop training gives you a good foundation to make your own way to become a furniture maker.
Build on the skills you developed in Woodworking I through the construction of a small cabinet. Woodworking II introduces students to miter and dado joints, hardware installation, and re-sawing on the bandsaw. Please bring a sketch for a small cabinet you would like to build to the first class. NOTE: Students are responsible for their own materials in this class.
A woodworker's Workbench is a special type of bench designed to hold your work when you are working on a wood project. The main purpose of this table is to keep the woodwork steady and to prevent it from moving. Follow the tutorial below to build yourself a nice workbench suitable for your specific woodworking projects. Make sure to modify the table to fit your specific requirements.
The last thing is to semi-permanently attach the bolts for the vises. Given the amount of work necessary to get to the bolt heads, once the top is joined, I had intended to tighten them up so they wouldn't spin, and lock them that way with blue Loctite. (That's the strongest non-permanent grade.) That didn't work. What I found was that the bottoms of the countersinks weren't quite flat, and when I tightened the nuts down that far, the ends of the bolts would be pulled far enough out of alignment that the vise bases would no longer fit. In order for the vises to fit over the bolts, I had to leave the nuts loose enough that the bolts had a bit of wiggle - which meant that they were almost loose enough for the bolts to spin. So I put Loctite on the nuts, to keep them from unscrewing, and filled the countersinks with Liquid Nails, in hopes of keeping the bolts from spinning. I considered using epoxy, or a metal-epoxy mix like JB Weld, but I didn't have enough of either on hand. It seems to be working for now, though the real test won't be until I have to take the vises off.
With the shelf secure, get a couple of friends to come help, and stand the bench on its feet. I said earlier moving the top by yourself is dangerous. Trying to lift the entire bench is foolhardy. Of course, I already said I'm stubborn, so I did it myself by rigging a simple block-and-tackle using lightweight pulleys I got at the hardware store. (Not the lightest-weight pulleys, those are meant for flag poles and have a design load of something like 40 pounds. These had a design load of 420 pounds.)
My advice? Don't do this. If you have jointer and a planer, use them. If you don't, seriously consider using dimensional lumber that has already been planed and sanded. If you are going to try to clean up construction lumber by hand, using a hand plane is a lot faster and more pleasant than using a belt sander. Except, of course, that to do a good job of planing a board you need a solid bench to hold the board, and you don't have a bench, yet.

Of course, few benches can be ideal, and this one does have some drawbacks. That being said, most of the disadvantages of this bench are minor annoyances rather than deal breakers. For instance, this bench does not include any kind of storage whatsoever. Though, it does have the option of adding numerous additional features like a storage area. Still, for the bench, you would expect a drawer at the very least, maybe a shelf below the main table area.
Timberframing is a traditional technique for building large and small structures using only wooden joinery. Prized for its structural integrity and beauty, as well as reliance on hand skills, timberframing is regaining popularity in modern applications. We will start with an overview of the different styles and aesthetics involved, and move into the specific tools that are used to lay out and cut the strong joints. Each student gets guided practice time making sample joints. We will all work together to make a small structure that can be raised on the final day of class.
Require the woodworker to be able to read the plans and to transfer images and dimensions from the plan to the lumber. The wood has been planed and all glued panels are completed unless over 14 inches. If panel required is over 14 inches, one glue seam will be required. The woodworker needs to be able to do some cutting, jointing, assembling and finishing. White Kits do not require planing. White Kits supply all of the needed hand-selected dimensioned lumber, but woodworking knowledge and tools will be useful to complete the project successfully.
I decided to make my own top out of white ash because I had access to a planer and jointer at my local college where I was taking an intro woodworking class. Trim and vice jaws are white ash as well. Everything else is built pretty much as jdege describes. A plunge router with a 3/4" spiral up bit really made quick work of the dog holes. Finished with Danish oil.
One aspect of the Windsor Design that is hit or miss is the vice. Notice we have to use the singular when describing it because this is the first workbench that we have reviewed which features only one vice. To make matters more frustrating, the vice cannot be repositioned along the bench. That said, the vice does at least have the largest capacity out of any we reviewed. At 7” capacity, the Windsor Design vice can secure any size workpiece you may have.
I don't see anywhere you mentioned the over all length of the bench top. A piece of 1 1/2" x 25" x 8' glued edge oak at Lumber Liquidators costs $192 including tax. Two piece is almost $400! Would that be better if I use two IKEA 1 1/4" x 25" x 74" solid Beech ($99 each plus tax) on top of a layer of 3/4" Birch plywood. That would be 3 1/4" over all.
Had a great experience at the shop! My schedule is hectic and unfortunately can't make the classes, but I did do a private lesson with Bob.  In one afternoon, we created two cutting boards.  Bob was very detailed with breaking down the process and using the machines.  Honestly didn't expect to make two cutting boards but Bob was proficient with time.  I got really comfortable using the machines especially the table saw.  I learned how to use the planer, jointer, miter saw, table saw, drill press, router, disk sander, and random orbital sander.  Really recommend folks that are interested in woodworking with little to no experience to take the Safety Orientation and the Cutting Board class or private lessons.  Looking forward to my next project at the shop!

The hacksaw will often damage the last thread when it cuts. Running a nut off the end will fix this. You'll have to run the nut all the way down from the other end. This doesn't take long, if you chuck up the rod in your drill and let it do the work. Hold the rod vertically, with the drill pointing down, and just hold on to the nut enough to keep it from spinning.
The Community Woodshop allows me to have access to a countless number of the best quality tools in the industry. They are always on top of keeping everything working and running.  If anything breaks they are always very proactive in fixing things ASAP.  They also have more than enough tools so I never have to wait to use a sander or any of the smaller tools, and I have never had to wait more than a few minutes to get on the table saw (and even that is rare).
I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.
In this two day class we will reveal some of the secrets to tuning up a Japanese Hand Plane (Kanna) We will start with conditioning the Body of the Plane (DAI) to stabilize movement. Proper sharpening and grinding of the blade and chip breaker will be discussed and demonstrated. Custom fitting the blade to the Dai and conditioning the sole. We will...
As you can see in the image, this shelf goes on both sides of the corner wall. It looks beautiful and can be used to organize books, trophies, pictures frames and many other things. The strength and design of the shelf depends on how properly you build it. First time workers definitely need some guidance to help them with the process. Therefore, I am including this basic video that I found on YouTube that demonstrates the process of making corner wall wooden shelves.
I'd intentionally made it oversize, intending to trim it flush. Trimming is a little more complicated than usual, because I needed to trim it flush on two faces. The end face extended a good 3/8", so I cut off most of the excess with a circular saw and the edge guide, then flipped the edge guide upside down to make a stable platform for the router. Aside from the use of the edge guide, flush trimming the edge face was unremarkable.

The Cape Ann Shed was designed with coastal New England in mind. So yard work may feel like you’re actually on vacation. From Cape Cod to the beaches of Maine, you will find a Post Woodworking Cape Ann shed adorning the yards of thousands of homes. It’s a popular style with our customers – whether they make their home by street or by sea. An affordable choice for an outdoor structure, the Cape Ann brings functional elements with nautical appeal.
×