Put the upper panel of MDF on your glue-up surface, bottom side up. Put the bottom panel of MDF on your other surface, bottom side down. (The panel with the holes drilled in it is the bottom panel, and the side that has the your layout diagram on it is the bottom side.) Chuck up in your drill the appropriate driver bit for the screws your using. Make sure you have a freshly-charged battery, and crank the speed down and the torque way down. You don't want to over-tighten the screws, MDF strips easily.
Working with wood fresh from the log, this green woodworking project is the perfect introduction to edge tools and wood grain. In the first week you will produce a three-legged stool using buck and “whip”saws for crosscutting the log to length; wedges and froes for splitting out leg stock; drawknife and spokeshaves at a shaving horse for shaping the legs; and using travishers, rounding planes and specialized rasps for shaping the seat.
At the age of 9, Mark’s interest in woodworking began, which led him to begin an apprenticeship with Homestead Heritage Furniture at the age of 17. In his own shop he has built many pieces of furniture from small dovetail boxes to large 10′ round conference tables. Most of his work has been for clients who have ordered custom pieces for their homes and offices. Mark has been building custom furniture for the last 20 years and is now the manager of the Heritage Furniture business. Mark enjoys making hand tools and jigs that can simplify the building process. He has taught children how to shape simple utensils like wooden spoons and cutting boards as well as other larger projects. “Seeing the young grow to maturity in their craft is what I appreciate.”
Happy bench building folks. I hope you make it your own and not worry too much about what someone else thinks it should be. Use the rules as a guideline, they have validity, but make it your own in the end. If the rules fit you that’s great, if they don’t quite fit you then make it to fit yourself. It’s you using it, not some guy making a nice living off of telling you how he thinks you should do it. One size does not fit all. Never has, never will.
Thanks Chris! I found this page while looking for a link to your e-mail address. I recently finished your erudite volumes on workbench design, and am about to embark on my own bench inspired by your take on the Holtzapffel design. As my vices and planer arrive, I’ve been agonizing over whether to use SYP or rough maple for the top. I don’t have a big budget, so all-maple is not an option. But after reading your ten tips here, I’ll stop agonizing — all SYP it is! This is, after all, my first of what I hope are at least several handmade benches. Your scholarship and craftsmanship are truly inspiring.
The original design had a height of 35-1/8". Their two-layer top was 1-1/2" thick, so their legs were 33-5/8" long. I want a height of 35", but I'm using a top that's 3" thick. My basement floor is anything but level, so I'm using levelers that are adjustable from 3/4" to 1-1/2". In other words, I want legs that are around 31-3/4" long. (If you're not using levelers, your legs need precise lengths. The levelers give about 3/4" of adjustment, so precision is less necessary.
In this class, John will explain and demonstrate safe spindle turning techniques for turning a bud vase or a carvers mallet, an essential tool for anyone wishing to sculpt wood or make hand made joinery. Objective Through hands-on learning students will gain experience and confidence using our new Laguna mini lathes. You will develop an understanding...
Well, not these plans. You have the option of building a very functional and spacious lean-to shed on different foundations. Your foundation choices are: concrete slab, a wooden floor supported by concrete piers, or a wooden floor supported by skids. That lost option also means that your lean-to could be mobile as well so you won’t have to decide where you want to permanently put it.
This instructable shows how to build, with basic tools and readily-available lumber, a bench that provides most of the function of a traditional woodworker's workbench. I began with a design by Asa Christiana that was featured in the second season of finewoodworking.com's video series Getting Started in Woodworking. The project plans are available on their website.
My advice? Don't do this. If you have jointer and a planer, use them. If you don't, seriously consider using dimensional lumber that has already been planed and sanded. If you are going to try to clean up construction lumber by hand, using a hand plane is a lot faster and more pleasant than using a belt sander. Except, of course, that to do a good job of planing a board you need a solid bench to hold the board, and you don't have a bench, yet.
The Classic Workbench is simple to use. The leg vise is used primarily for working the edges of boards and the ends of narrower boards. This is self explanatory. To work the faces of boards along the grain, tap up the planing stop (don’t make it any higher than necessary) and butt the end of the board into the teeth of the stop. With the right technique you can plane across wide boards without repositioning the board. You usually don’t need to tap the opposite end of the board to engage it with the stop, but in some cases, especially with rougher stock, you may need to give a tap with your mallet. Working the faces of a stack of boards is extremely quick with the planing stop since you don’t have to open and close a vise constantly. To work across the face of a board, make yourself a doe’s foot and position it at the back corner of the board, holding it down with a holdfast. The doe’s foot is simply a piece of wood with a V-shaped notch cut into one end. The bottomsurface of the doe’s foot can be lined with sandpaper or Crubber to help it stay put on the bench top. To work long boards, fasten a batten to the right leg with a holdfast and use that to support the end of the long board. We’ve found that a deadman is not necessary for the majority of work, especially on a bench of this length. For working the ends of smaller boards the leg vise can be used, but for precision work like dovetailing, we use and recommend our Moxon Vise.
Linseed oil sitting in a bowl, or spread on the surface of wood, is perfectly safe. But a linseed oil soaked rag provides a vastly increase surface area, so the oxidation happens faster, and the rag can provide insulation, trapping the heat. The increased temperature speeds up the oxidation even more, which raises the temperature even more, and the runaway feedback can quickly result in temperatures that will cause the rag to spontaneously burst into flame. This isn't one of those "do not drive car while sunscreen is in place" warnings. This is one of those "keep your finger off the trigger until you have the gun pointed at something you want to shoot" warnings. Rags soaked in linseed oil will catch fire, if you don't handle them properly, and they can do so far more quickly than you might think.
Synopsis: No room in the garage? Basement not an option? Consider what Ken St. Onge did when he needed shop space: He bought a prefabricated shed and converted it into his full-time woodshop. Because a pre-built shed doesn’t need a cement foundation and is built in a factory, it’s much less expensive than building an addition or stand-alone shop on your property. It can have taller ceilings than a garage and bigger doors than a basement, both big pluses for a woodworker. You can put a shed just about anywhere, too. Here’s a soup to nuts look at Ken’s experience, so you can gauge whether a shop in a shed is right for you.