Looking for a great gift for a friend or family member or maybe a Christmas gift? Recommended woodwork projects include a turned wood box with a lid or how to make a jewlery box. New to woodworking? Great! Check out these simple beginner’s woodworking projects. No matter the DIY woodworking project you can find your next gift idea in the wood craft videos listed below.
I mocked up the two scenarios, and determined that with the plate inside the stretcher the vise would have a reach of 8 inches, and with it outside the stretcher it would have a reach of 9 inches. I decided that 8 inches was enough, and that the extra inch wasn't worth the extra effort. With the end vise mounted like this, the right edge of the top would have no overhang.
I agree that even at 12x12, things'll be "cozy" inside. That's OK. Keep in mind that this will be a general purpose hobby shed, not just a wood working shed. Even 12x8 would be plenty big enough for building 1 meter wingspan bungee launched RC gliders. And for the electronics projects I do, I only need enough workbench space to do some soldering with a 3rd hand (for electric guitar pedals). If I need more room than the shed offers for wood working projects, I'll just roll the table saw down a ramp and do my cutting outside in the sun.
There are a number of tricks to using a router. First, the bit spins in a clockwise direction, as you look down at the router from the top. This means that when you cut with the router from left to right, the bit will tend to pull the router away from you, and when you route from right to left, the router will pull towards you. So, if you're hooking the edge guide along the near side of the board, route from left to right, and when you're hooking it along the far side of the board, route from right to left. Second, always test the position of your bit on scrap material. Your odds of getting it exactly right by eye are nil. Third, don't cut more than 1/4" deep on a single pass. We want a 3/8" deep grove, so make your first pass at 3/16", or thereabouts, and make a second pass to reach the full depth.
First, cut one long edge. Second, cut a short edge, making sure it's square to the long edge you just cut. Clamp both pieces of the edging you'll be using along the long edge you've cut, and measure the width of the base plus 1/4-1/2", mark that, and then lay out a line through the mark that is square to the end you've cut, then cut along the line. Finally, cut the remaining short edge square to both long edges. (The length of the top doesn't need to precisely match anything, so we don't need to bother with clamping the trim before measuring.)
In terms of size, this bench is another Sjobergs that is a bit on the small side, though it is actually far more squared than some others. While its length is a bit disappointing at 54″, the width is over 24″ wide which does provide for more diverse projects. Even better, this product still features the incredibly 500-pound weight capacity and continues the Sjobergs trend of avoiding joints that are not as durable as they otherwise could be.

2 - use a plunge router with a bottom bearing cuter bit such as this from rockler: http://www.rockler.com/product.cfm?page=25160&site=ROCKLER .... I thought to use the short one as I plunge it directly downward in the centre of the hole until the bearing reaches within the tabletop hole. I suppose one could use a long one, but the stubbiness seemed more practical (the big bearing ensured accuracy?)

Isn’t this amazing that instead of having to throw that old furniture piece away, you can now reuse it to build something even more beautiful? If you do not like this particular idea, there are many other re-purposeful furniture items you can build from an old dresser. Just search the internet for other DIY project ideas. Here is a link to the video tutorial that explains the same procedure in a more practical manner that you can easily follow through.
Our sizing options range from 6′ x 8′ to 13′ x 36′, and even larger depending on your chosen style. We’ll work with you to design a custom solution based on your needs and property, with many door options, window options, trim colors, shelves, siding and roofing choices to choose from. We deliver a large portion of our sheds fully assembled using our lightweight “mule,” but we also provide an on-site build option for those really tough to access sites.
You are absolutely right on your advise. When I was agonizing over how to build a workbench my good friend turned me on to your book on workbenches. I was planning on having an overhang until I read your advise about building a workbench and not a table. So the entire front and rear surfaces; top, legs and bottom shelf are all in the same plane to clamp my work to. The addition of a sliding dead man was also something that I would have never thought of on my own. Thanks again for your advise.

I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.
Building a Wooden Office Desk Organizer is an easy task for a professional woodworker, but not so much for normal people like you and me. But that doesn’t mean you cannot do this. Two years ago, I had almost no woodworking experience, but now I make most of my household and office wooden items by myself. This saves me a lot of money. And believe me when I say this; you can also manage to make wonderful wood items with a little practice and some woodworking experience.
Still, one of the best features about this woodworking bench has to be its vices. First off, the Sjobergs provides two vices both as sturdily constructed as the bench itself. The same hardware that fastens the bench works to ensure the vices are just as strong. The next main benefit on the vices in the inclusion of multiple positions – four in total – for the vices to go. This allows you to mix and match to suit your needs and allows the table to be used just as easily by right-handed and left-handed users.
Our programs prepare our students to open their own woodworking business or become employed by a high-end woodworking related business. We currently offer an Associate of Science Degree as well as a Certificate of Achievement in 8 different Program Areas. Students may also take coursework to complete a Certificate. Our courses range from Furniture Design and Instrument Making to Production Cabinetmaking.   Our graduates are highly employable with the diversity of courses available.
Ok, I’ve had my morning coffee and now it’s about time to get out to the shop to see what I can do to make that bench a little more pleasing to my eye. I like that Craftsman flair idea. That was my intent at the time I built it, too bad I got lazy and rushed the job. It’s not like I was going to make hundreds of benches for someone else and would never see it again. I should have taken the time to make it the way I wanted it to look. This could keep me entertained for awhile. I see major surgery in the forecast! Gotta plan it all out just right.
Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.
Frame making may look simple but it is a skill that escapes many. For a frame to properly do its job it has to be perfect, any mistake can be a distraction that takes away from the artwork it surrounds. This class will focus on skills essential to making square or rectangular frames. Skill building concepts will include how to break down and mill...
The next day, cut it flush. Use a block plane to ensure it truly is flush. This will be the top of the bottom layer of the bench top, so gouges aren't a problem. (Wiping up glue with a damp cloth can lead to stains and finishes applying unevenly. That won't be a problem here, either.) But bulges and bumps are a problem - they will keep the two layers of the top from matching up evenly.
With the top laying on the floor, bottom side up, the next step is to flip the base upside down, and attach it to the top. I followed Asa Christiana's design, in using s-clips. When I stopped by my local Woodcraft, though, they only had two packages of ten, so I didn't use as many as I would have, otherwise. For the top I put four on each side and two on each end. For the shelf I put three on each side and two on each end. If it turns out that I need more, I can always add more.
Here, I am writing about another DIY project that involves the use of an old furniture piece. I think that the idea of reusing and recycling old furniture has got to me. Anyways, I am starting to love it. This project involves using an old door to build a beautiful multi picture frame, as you can see in the image below. This frame looks really wonderful and can be used to hold many pictures at a time.
Learn to use hand and power tools to shape wood into objects that will last for decades. You’ll learn about the properties of lumber, safe tool use, measurement and layout, and fundamental woodworking joints. At the end of this week-long course, you’ll leave with an end-grain cutting board, a mitered corner box, and the skills to build an unlimited range of wooden objects.
The first time you try your hand at the ancient craft of woodworking, you want to do it right. Learn woodworking basics with hand tools to a professional standard on a weekend woodworking course at Rowden Atelier. Ed Wild runs weekend furniture building courses for everyone from beginners who want to have some fun experimenting behind the bench, to those who are looking to develop specific skills as a furniture maker. Classes include tool handling, box making, and basic veneering, but to a certain degree, you can tell us what you want to learn - these short woodworking courses are partly bespoke.
Isn’t this amazing that instead of having to throw that old furniture piece away, you can now reuse it to build something even more beautiful? If you do not like this particular idea, there are many other re-purposeful furniture items you can build from an old dresser. Just search the internet for other DIY project ideas. Here is a link to the video tutorial that explains the same procedure in a more practical manner that you can easily follow through.
With the Grain: A Craftsman’s Guide to Understanding Wood by Christian Becksvoort. A little knowledge about trees goes a long way toward improving your woodworking. You don’t need a degree in dendrology to build a desk. But you do need intimate knowledge of how our raw material grows and – more importantly – how it responds to its environment after it has been cut and dried.
My advice? Don't do this. If you have jointer and a planer, use them. If you don't, seriously consider using dimensional lumber that has already been planed and sanded. If you are going to try to clean up construction lumber by hand, using a hand plane is a lot faster and more pleasant than using a belt sander. Except, of course, that to do a good job of planing a board you need a solid bench to hold the board, and you don't have a bench, yet.
Our programs prepare our students to open their own woodworking business or become employed by a high-end woodworking related business. We currently offer an Associate of Science Degree as well as a Certificate of Achievement in 8 different Program Areas. Students may also take coursework to complete a Certificate. Our courses range from Furniture Design and Instrument Making to Production Cabinetmaking.   Our graduates are highly employable with the diversity of courses available.
Why would you buy a costly platform bed from Ikea or somewhere else when you can make one yourself at home? Oh yes, you can. A bed is the most common furniture piece used in the house and probably the costliest one. Wouldn’t it be great if you could just make a bed of your own, without having to spend many bucks for buying one? So I am here sharing a great tutorial to help you to build a nice comfy platform bed that you can use anywhere in the house.
I’ve seen antique cabinetmakers’ benches that are sixteen and seventeen feet long, more than three feet wide, and supported by a dozen drawers and doors—and that weigh as much as a felled oak tree. In contrast, jewelers’ cabinets seem to be on a dollhouse scale, with tiny tools to match. For most of us, however, space limitations preclude the biggest, and the smallest are just not big enough.
If you don't quite have the space for a real pony, make this handcrafted wood version instead. The horse pictured here is unfinished pine, but there are lots of woods and finishes to choose from. Everything you need comes with the kit, and the plans can be downloaded. If you don't want to build it yourself, you can order from the website—just allow two to three weeks to ship.
In the "Getting Started with Woodworking" video, the holes through the 4x4's were drilled from the back. That is, they start on the side opposite the precisely-positioned mark, and drill through to hit it. If they can do this, more power to them, but I can't drill through 3-1/2" of wood to emerge at a precise mark without a drill press - and not always then.

I had a similar experience with running electrical power to a shed. It turned out that I could build a 12x12 shed without a building permit as long as I did not run utilities, but getting a permit opened a whole new set of requirements that forbid me from having a shed at all. And when the nosey old woman next to me kept calling the building inspector on me, it was suggested that I could run an extension cord out to the shed anytime I wanted as long as it wasn’t fastened in a permanent manner.
×