Rocking horses, toy chests and dollhouses are just a few of the classic gifts generations have treasured. Now you can give all the pint-sized DIYers on your list those same classic gifts, and make them yourself with the help of these DIY toy kits. They're perfect for kids of all ages, and will be treasured for years to come. The best part? All these gifts can still make it to your door by Christmas.
Can you believe that this amazing wine rack the image below has been built using old wood pallets? Perhaps you can. Isn’t it wonderful that your old wood pallets can be reused to build something so beautiful and useful? I am not a drinker but I liked the idea so much that I just couldn’t resist making myself one. Although later I gifted it to my parents, who totally loved it.
Clamp the inner jaw of the end vise in position, leaving a little bit to trim off later, and then use the dowel and dowel center trick through the screw and guiide rod holes of the vise base plate to mark the position of the screw and guide rod holes in the jaw. Remove the jaw and drill 1-1/8" holes in the marked positions. I used the drill guide for most of the holes, and drilled freehand for the last bit. When you're starting a spade bit in a deep hole like this, start the drill very slowly, and the bit will move the drill into a perpendicular position. Start it too fast and the bit will bind and you'll damage the sides of the hole.
My first attempt at making a cutting guide didn't work. What I ended up with worked fine for cutting panels, but the guide-strip was too narrow, and when the saw was extended fully for rough-cutting the 4x4's the clamp heads got in the way. So I made another. Actually, I made two more, so that I could cut one into shorter pieces that would be easier to handle.
to allow 9' at the peak, I like a "shed style" roof, but that may not fly in your HOA.I'd put double doors on or one large one, pour a slab, or use patio blocks then lay down Wolman. plywood for a floor, I would use foam insulating board everywhere I could, walls, floor and ceiling. A few bin type windows or sliders would let in light and fresh air. If you can't get away with your wiring idea, I would use a HD 30 amp twist lock extension cord with an "outside weatherproof outlet" mounted on the home professionally installed for code, 2- 8' long flouresent lights, and a 20 amp outlet inside for a heater and dehumidifier. Dehumidifiers draw about 5-6 amps. You might be better off with a small 6000 BTU window or wall mounted AC unit,( $100 on sale at the Depot), it will take the moisture out of the air and cool it as well in the summer. I'd use thin wall conduit around the shop with about 4 double duplex boxes. You may be able to bring 220v. in and then split into 2-120v circuits. If you make ANY dust in this confined space you must first catch it with a shop vac, then filter the air, and wear a mask. A bathroom ventilator fan would exchange the air and be quiet. A slab in front would allow sawing outside weather permitting. A roll up canopy over the door way would provide "shade" and rain protection. I know this sounds like a lot of work, but I know you can do it if you try. You can get plenty of "free" advice here and from an expert close to you. My neighbor enlisted the help of a handyman for building his 2 sheds and they became friends and did tool swaps and labor trades for time worked. My advice to you.. go 4 it! bill
Yea I had a friend who went the HD route and in after putting new braces up for the roof and an extra layer of plywood on the floor he gave up the fight and tore it down. We ended up building twice the shed that was 100 times more sturdy for less than he had invested in the first one. I would go any route that is the opposite way of HD or Lowes. Learn from this guy.
You don’t need a fully equipped shop to enjoy woodworking! In this class, you will learn to design, make, and finish a unique wood box. With an emphasis on tool safety and material exploration, we will use a combination of power tools and hand tools to make boxes of all shapes and sizes. Beginning with a solid block of wood, you will learn how to lay out, cut, sculpt, and reassemble the block into the form of a box. Demonstrated techniques will include hidden hinges, small drawers, pull knobs, and fitted lids, as well as texturing, carving, burning, painting, and finishing. Suitable for beginning and intermediate students, all materials provided.
In this class, John will explain and demonstrate safe spindle turning techniques for turning a bud vase or a carvers mallet, an essential tool for anyone wishing to sculpt wood or make hand made joinery. Objective Through hands-on learning students will gain experience and confidence using our new Laguna mini lathes. You will develop an understanding...
This is used to secure workpieces in place while you work on them – often for jointing. The location and capacity are the important things to look at. Most vices will come on a right-hand configuration either on the front or the side of the bench. If possible, it is a good idea to look for vices that can be repositioned. In terms of capacity, anything over 5” is solid while anything under 4” is likely a bit too small for all projects.
I have always wanted to share this wonderful woodworking world with like-minded people from all over the world. For the last six months, I have started sharing Japanese woodworking information through videos and photos. Because of the huge amount of interest, I started organizing one-day workshops for people visiting Kyoto, letting them experience Japanese woodworking tools.
This Vermont Farmhouse by Real Good Toys is as pretty as the real thing. And if the seven-room home isn't big enough for the serial renovator in your kid, the site also sells additions that add two rooms to either end of the house. Just like the homes old-house lovers hope to own, this farmhouse comes with real wood shingles, wood floors, interior crown molding and a spacious porch.