Laney College is located in Oakland near the San Francisco Bay and currently enrolls around 12,000 students. The Wood Technology Department offers 1- and 2-year certificate programs in wood technology, computer-aided drafting and design, as well as an apprenticeship program and carpentry courses. Students have access to eight faculty members and a variety of woodworking machinery and equipment, including a lathe.
Thread the rods through one of the legs, then set the leg flat on the table. Insert dowels into the dowel holes. Place the matching stretchers into place. Put dowels into the dowel holes at the top end of the stretchers. Place the other leg onto the threaded rod and settle it down onto the dowels. You'll probably have another opportunity to whack away with your rubber mallet.
In the middle third of the course, you’ll build a tool tote that features dovetails joining bottom-to-end boards; rabbeted and copper-nail pinned side boards; shaped end panels and curved handles passing through angled mortises. This joiner’s tote also features a lift-out box for layout tools with lapped (or optionally dovetailed) corners and a sliding lid.
The Classic Workbench is based largely on the famous Plate 11 workbench from Roubo’s “The Art of the Joinery”. We’ve built dozens of these “Roubo” benches over the past decade, helped others build hundreds more and examined extant French benches from the period. We haven’t changed our opinion on this fundamental design. French technical schools of the late 19th and early 20th centuries were outfitted with benches of the exact type. And prior to the 1950’s, you could easily buy a “Classic” workbench from any number of French supply houses. Benchcrafted continues the tradition by offering this excellent workbench, built in Iowa with American hardwoods to the highest standards.
My wife has given me the OK to buy a "Rancher"-style shed from Lowes and have it installed in the backyard. The discounted installed price will be about $2,600 and this includes the 12' x 8' structure along with a lot of upgrades (twin metal doors, a window, 2 skylights, storage, vents, etc.). I can save about $300 if I build it myself, but my skill level isn't there yet, so I'm going to pay Lowes to assemble it. (See Post #12 below for some photos of the shed and the space I have to work with.)
Linseed oil sitting in a bowl, or spread on the surface of wood, is perfectly safe. But a linseed oil soaked rag provides a vastly increase surface area, so the oxidation happens faster, and the rag can provide insulation, trapping the heat. The increased temperature speeds up the oxidation even more, which raises the temperature even more, and the runaway feedback can quickly result in temperatures that will cause the rag to spontaneously burst into flame. This isn't one of those "do not drive car while sunscreen is in place" warnings. This is one of those "keep your finger off the trigger until you have the gun pointed at something you want to shoot" warnings. Rags soaked in linseed oil will catch fire, if you don't handle them properly, and they can do so far more quickly than you might think.
In the Port Townsend School of Woodworking’s twelve-week Woodworking Foundation course, you will learn the essential skills, tools and mindsets of the traditional joiner. This is NOT an industrial arts course with a focus on machinery and production processes. Rather, it is a course in PRE-industrial artisanship--the creation of individual works through mostly hand tools and skills..
I don't like to be ignored either. I came the same day Mahndo left after waiting 30-45 mins. I left a note with name and number but no one even called me back. I was completely ignored. I found a class over at The Corona Heritage Park in Corona instead. Their instructor answers when I call or text. Nice to be acknowledged! Going to finish beginning and take advantage of the key access in their intermediate class.
I'd intentionally made it oversize, intending to trim it flush. Trimming is a little more complicated than usual, because I needed to trim it flush on two faces. The end face extended a good 3/8", so I cut off most of the excess with a circular saw and the edge guide, then flipped the edge guide upside down to make a stable platform for the router. Aside from the use of the edge guide, flush trimming the edge face was unremarkable.
When the top is done, we want the edged MDF and the oak countertop to have exactly the same dimensions, and for their width to exactly match the width of the base.I could see three ways of doing this: 1, join the MDF to the countertop and use my belt sander to sand down their joined edges to match the base; 2, join the MDF to the countertop and use a hand plane to plane down their joined edges to match the base; or 3, use a flush-trim bit against a straight edge to route the MDF to the width of the base, then join the MDF to the countertop and use the flush-trim bit to route the countertop to match the MDF.
I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.
Another aspect that might irk some buyers is the fact that the capacity of this bench is less than great outside of weight. The top’s surface area is a bit on the smaller end, though its length is more in line with larger models. The width though is less than two feet which can limit some projects. Similarly, the vice capacity is the second smallest on our list at 4 ½”, though this too can be modded with optional additions.
The holes we want to mark are the holes through which the threaded rod connecting the two legs will run. This threaded rod will run through the 3/8" groove along the bottom of the short stretchers,. The hole for the upper stretcher has to be positioned so that when the rod is running through this groove, the top of the short stretcher is even with the top of the legs. The most precise way I've found for marking the position of this hole is to use a dowel center. Fit the dowel center into the bottom groove, line up the stretcher, and bang on the end with a rubber mallet. The dowel center will leave a mark indicating the center of the hole.
All-in-all, the Windsor Design workbench is a nice companion, especially if your budget is limited. It is not as deeply designed and perfected as the other two benches, as there is only one vice, the bench dog holes are drilled through the surface (allowing debris to fall to the top drawers) and the drawers can be a little flimsy if you are not using glue for assembling it, but for the price they offer, there are plenty of perks.
Traditionally woodworkers (joiners) learnt their craft working as an apprentice in the Master Craftsman's shop doing the grunt work and learning by assimilation over many years. Our approach is a little different. We're making the assumption that you're smart; are developing or already have a passion for woodworking; and can devote three months to intensive learning.
You're not the first person to say this! I'm half inclined to use the Lowes shed as a starting point for my own design. But I do think I'd feel better if I could work as an "aprentice" next to an "old master". Someone at work is going to put me in touch with a guy who builds sheds for a living, and apparently he's competitive with the prices @ Lowes and HD. The Lowes shed comes with a "Handman Package" that I don't want but would end up paying for, anyway. The "workbenches" were laughably flimsy.