In the Port Townsend School of Woodworking’s twelve-week Woodworking Foundation course, you will learn the essential skills, tools and mindsets of the traditional joiner. This is NOT an industrial arts course with a focus on machinery and production processes. Rather, it is a course in PRE-industrial artisanship--the creation of individual works through mostly hand tools and skills.. 

The bench I will be describing differs from both of these in a couple of areas, the most significant of which is the top. Allen's top was made from three layers of 3/4" medium density fiberboard (MDF), topped and edged with 1/4" hardboard. Christiana's top was just two layers of 3/4" MDF. My top is two layers of 3/4" MDF edged with 1/2" oak and topped by a 1-1/2" thick edge-glued oak Ikea countertop. My top is more expensive in both time and money than either Christiana's or Allen's. If you're looking to build something fast and cheap, I'd recommend Allen's approach over Christiana's. The hardboard significantly increases the durability of the top.
I had a similar experience with running electrical power to a shed. It turned out that I could build a 12x12 shed without a building permit as long as I did not run utilities, but getting a permit opened a whole new set of requirements that forbid me from having a shed at all. And when the nosey old woman next to me kept calling the building inspector on me, it was suggested that I could run an extension cord out to the shed anytime I wanted as long as it wasn’t fastened in a permanent manner.
I am blown away with their ability to teach, a rare characteristic in my opinion, even more so is their passion to do so. I feel that they are able to accurately depict the philosophies and ideas mentioned in your website. My expectations did not even come close to the actual experience I have been given, and that is only in a short short time! I can only dream of what the next 11 months will bring! I am convinced my decision to study at Rowden Farm is the best one I have made to date! Thank you! Much appreciation and gratitude!”

Linseed oil sitting in a bowl, or spread on the surface of wood, is perfectly safe. But a linseed oil soaked rag provides a vastly increase surface area, so the oxidation happens faster, and the rag can provide insulation, trapping the heat. The increased temperature speeds up the oxidation even more, which raises the temperature even more, and the runaway feedback can quickly result in temperatures that will cause the rag to spontaneously burst into flame. This isn't one of those "do not drive car while sunscreen is in place" warnings. This is one of those "keep your finger off the trigger until you have the gun pointed at something you want to shoot" warnings. Rags soaked in linseed oil will catch fire, if you don't handle them properly, and they can do so far more quickly than you might think.
We have 4 newly expanded Classrooms, 3 state of the art labs with over $275,000 of new machinery, and $600,000 spent on new exhaust and compressed air systems. We have 4 new CNC production machines, a Haas VF-3 CNC Router and a NEWCNC 4×8 multi head machine and 2 Laguna IQ Routers. Even our shop stools (with cushioned backs) are brand new. We have new course offerings such as our Computer Design Sketchup Class and 8 new Certificate Programs you can choose from.

If you remember, when drilling the MDF I finished the holes from the other side using a Forstner bit. It made for a clean hole, but the positioning wasn't as precise as I really wanted. So for this, I decided to clamp a length of scrap MDF to the back side, and to drill straight through. My Forstner bits were too short, so I bought an extender. And then I found that the spade bits I was using gave a cleaner exit hole. Whooda thunk?
In class, each student will build a detailed hall table that is complete with mortise and tenon joinery, biscuit, dowel, and floating joint construction.  The student project is presented with a variety of design options and formats as to meet the experience and comfort level of each student.  Depending on their experience and comfort level, students are encouraged to make a simplified version of the hall table or tackle a more sophisticated and complicated version of the same project. Your only limitation is the amount of material you receive in your lumber pack (~24 board feet).
There is a mandatory safety class you have to take where they walk you around the shop and make sure that you know how each major machine works and general shop safety. You also have to sign a waiver saying you are participating at your own risk. You DO NOT have to take that safety class if you are signing up for one of their classes. They will cover those basics during the class.
I was using 2-1/2" coarse Kreg pocket hole screws. Kreg screws are supposed to be self-tapping, but the coarse-thread screws are intended to be self-tapping in softwood, and the fine-thread screws they intend for use in hardwoods aren't available in 2-1/2" lengths. I decided to drill pilot holes in the oak. Just to make sure, I did a test hole in the scrap piece I'd cut off.
The decision to be made with respect to the end vise is whether the support plate should be mounted to on the inside or on the outside of the stretcher. Mounting the plate on the inside of the stretcher reduces the reach of the vise - it can't open as far, because the support plate is back from the edge by a couple of inches. But mounting the plate on the outside of the stretcher means that we need to add some support structure for the inner jaw of the vise, which the legs would have provided if we'd mounted the plate on the inside.

The 84-906 fits this bill perfectly as the table offers all of the qualities and features that you would expect but does not truly blow you away with any of them. For instance, this bench is made out of rubberwood. This wood is decent in that it provides the strength you want, but it is also extremely porous and rough-grained. The porous nature would generally make it susceptible to rotting and staining, though the bench has been lacquered. The rough grain will potentially cause tools to dull over time if you do not regularly relacquer it.

These things may be tiny in size, but building one is not that easy. It takes some serious woodworking knowledge and skill to build a nice wooden mobile stand. When I first saw one online, I just couldn’t resist thinking of buying one. But when I saw the price, I was forced to rethink. Also, a woodwork lover like me cannot be contained with just one piece and I was not willing to spend on more than one. So instead I decided to build myself one. Yes, it took some doing but the final result was satisfying. Luckily, I found this awesome tutorial online that helped me build my first ever wooden phone holder.
You can buy sandpaper, glue, and other consumables from them for a nominal price. Their hand tools are propitiatory though so you would have to buy a specific kind of orbital sandpaper, for example. You couldn't just get generic. They are reasonably priced though. There is literally a coffee can with money in it and prices written on the boxes with these consumables. If you think you might burn through enough sand paper on something, check the brand and price shop.
While $115 may seem expensive, try accurately boring a grid of 20mm holes on 96mm centers in 3/4 MDF. I have for a table for our retirement community shop - - its a pita. Plus the MFT material seems denser and more water resistant than garden-variety MDF. And the single-thickness has proven sufficient the last several years on my original 1080s. Still dead flat.
Olympia Tools is a bit of a lesser known manufacturer. While they offer a wide range of products for a variety of construction fields, they are definitely more of a budget option. That said, Olympia Tools is one of the few brands that manages to produce a reasonable quality at a low price which makes them a solid choice for customers looking to get the best bang for the fewest bucks.
I marked the holes by putting a dowel center in the end of a long piece of 1" dowel. Run it through the holes in the base plate, and bang on its end with a mallet. Rotate it a bit and bang it again, and repeat. Odds are the dowel center won't be precisely in the center of the dowel, so you'll be making a small ring of marks. The center of the hole is, of course, the center of that ring.
The decision to be made with respect to the end vise is whether the support plate should be mounted to on the inside or on the outside of the stretcher. Mounting the plate on the inside of the stretcher reduces the reach of the vise - it can't open as far, because the support plate is back from the edge by a couple of inches. But mounting the plate on the outside of the stretcher means that we need to add some support structure for the inner jaw of the vise, which the legs would have provided if we'd mounted the plate on the inside.

Require the woodworker to be able to read the plans and to transfer images and dimensions from the plan to the lumber. The wood has been planed and all glued panels are completed unless over 14 inches. If panel required is over 14 inches, one glue seam will be required. The woodworker needs to be able to do some cutting, jointing, assembling and finishing. White Kits do not require planing. White Kits supply all of the needed hand-selected dimensioned lumber, but woodworking knowledge and tools will be useful to complete the project successfully.
If you decide upon construction lumber, you want kiln dry lumber. Green lumber will warp on you as it drys. Dig through the stacks and pick out the straightest, cleanest pieces. Generally, the boards that are sitting loose on the stack are those that other people left behind, as they sorted through looking for better. Be prepared to move them out of the way, and to dig down to the better stock. Be nice, though, and put everything back when you're done.
Place sounds amazing. Receptionist was rude. Sarcastic remarks were not necessary. I called regarding the private lessons. And was told that they "can't hold my hand to do the work". The person made the statement not allowing me to finish saying that I have experience with wood work. I was really upset by the statement. He did not seem interested in having me as a client/student.

I never, ever, ever bother to write these things. But, I am so incredibly impressed with this product, that I feel compelled to. My six year old daughter LOVES IT, as does my almost four year old daughter. The hammer is just the right size, and it comes with enough pre-cut (good quality) wood for many projects. So far, they have made a house, car, and a plane-- all of which are far more aesthetically pleasing (to me, as a mom) than the plethora of junky plastic toys that seem to fill our home. We've used these projects both as math lessons (measuring the wood, counting the nails needed, learning about angles, reviewing shapes) and during arts & crafts time; but, with just a little creativity, they could be incorporated into just about any learning subject. For the amount of enjoyment we have received, thus far, this product is already worth the money spent, and we have several more projects to go! We will be buying another for little sister's upcoming birthday, most definitely.
I agree that even at 12x12, things'll be "cozy" inside. That's OK. Keep in mind that this will be a general purpose hobby shed, not just a wood working shed. Even 12x8 would be plenty big enough for building 1 meter wingspan bungee launched RC gliders. And for the electronics projects I do, I only need enough workbench space to do some soldering with a 3rd hand (for electric guitar pedals). If I need more room than the shed offers for wood working projects, I'll just roll the table saw down a ramp and do my cutting outside in the sun.
×