This is another example of small woodwork projects that require good time and woodworking skills. This item is built using multiple wooden parts. Each part is shaped in a specific design and then all parts are attached together to make the final TV set. I have never tried building this one, mostly because I don’t own an iPhone, but also because making this item is not an easy task. By the way, it works fine with all kinds of phones.
In ancient times, the woodworker’s bench consisted of a plank or split log with four splayed legs. Descendants of those benches are manufactured today, usually with a top of hardwood slabs glued together. The norm nowadays is four straight legs supporting the bulk above, often with braces and a shelf below. Despite the improvements, the linkage to Greek and Roman antecedents is still evident.
I like the idea of re-inventing the wheel. I choose to believe that while others may have considered these improvements, they just never got around to trying them out. Brain gets bored with status quo. So, I try to keep Brain happy with the occasional foray into uncharted territory. And I must say Brain has had some really good results. Thanks, in part, to you, and the Roy. You never know where a good idea might come from so I’ll check in once in a while. That and make sure to build it in Sketchup first.
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
Let me see if I can come up with a couple details. The table saw is a TS3660. So I have heard, this should be the center of your shop. My jointer is a 6 1/8" Jointer / Planer JP0610 which is 45 inches in length. My router table is the kreg router table that takes up a 24 x 32 inch footprint. My bench is roughly 30 x 70 inches and my bandsaw is 3' x3'. I have other tools as well such as a portable 12.5 Delta thickness planer in addition to a wall mounted dust collector. To add to the list, I am just about to get a 10 inch makita sliding compound miter saw. I can see how space will be eaten up quickly. Any ideas as to how arrange these tools in such a small shop? I will get pics a soon a I
Out of all the shed books I have read, this book stays by my side while I hammer in the yard. The book is well written by what appears to be a non professional book writer (A Good Thing). It reads as if you are getting advise in laymans terms from your neighbor "The Craftsman", a welcome change from the DIY books, that assume a level of expertese. The level of detail is high and discusses gotcha's, advise, and trade "secrets" that could have only come from years of personal experience building sheds.
The popular account showcases woodworking in a variety of ways. Many of the things they share are of artworks produced using its techniques—including My Modern Met favorite Gabriel Schama. Other posts highlight its practical applications in the form of furniture or flooring, while videos offer a look into the process and range from educational to oddly satisfying. Whether you’re a fan of woodworking or looking to try it yourself, @wooodworking will both mesmerize and inspire.
My advice? Don't do this. If you have jointer and a planer, use them. If you don't, seriously consider using dimensional lumber that has already been planed and sanded. If you are going to try to clean up construction lumber by hand, using a hand plane is a lot faster and more pleasant than using a belt sander. Except, of course, that to do a good job of planing a board you need a solid bench to hold the board, and you don't have a bench, yet.
Our programs prepare our students to open their own woodworking business or become employed by a high-end woodworking related business. We currently offer an Associate of Science Degree as well as a Certificate of Achievement in 8 different Program Areas. Students may also take coursework to complete a Certificate. Our courses range from Furniture Design and Instrument Making to Production Cabinetmaking. Our graduates are highly employable with the diversity of courses available.
By following the Woodworking Course, Woodworking Classes or Start Your Own Woodworking Business Course, you eliminate mistakes most woodworkers make when working on their first project or starting their first woodworking business. Learn the importance of wood selection, joinery and tool purchases. You will understand how to start and make your new woodworking business successful.
I agree that even at 12x12, things'll be "cozy" inside. That's OK. Keep in mind that this will be a general purpose hobby shed, not just a wood working shed. Even 12x8 would be plenty big enough for building 1 meter wingspan bungee launched RC gliders. And for the electronics projects I do, I only need enough workbench space to do some soldering with a 3rd hand (for electric guitar pedals). If I need more room than the shed offers for wood working projects, I'll just roll the table saw down a ramp and do my cutting outside in the sun.
All-in-all, the Windsor Design workbench is a nice companion, especially if your budget is limited. It is not as deeply designed and perfected as the other two benches, as there is only one vice, the bench dog holes are drilled through the surface (allowing debris to fall to the top drawers) and the drawers can be a little flimsy if you are not using glue for assembling it, but for the price they offer, there are plenty of perks.