Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.
Be careful. Single 24x60" sheets of 3/4" MDF are pretty easy to lift. A doubled sheet is manageable. The countertop - 24x72" panel of 1-1/2" oak - weighs something over 100 pounds. It takes real care to lift safely. The joined top - 3" thick of oak and MDF - is past the range that can be lifted safely by one person. Don't try. Get a friend to help, or rig a block-and-tackle.

The video explains the step by step process of making a nice wooden phone stand from scratch. My first wooden holder was not the best one, but it was good enough to motivate me to make more. I now possess 10 mobile wooden stands in different shapes and styles. And if I can make this, you too can make one yourself. Search the internet for more mobile holder ideas and start making one now.
Those bums even have a stipulation that you can't connect any utilities to a shed. My plan is to adhere to the letter of the law if not the spirit. I plan to run a buried 20 amp power line out to the shed (this will be done professionally and properly according to whatever is required by the law), but it will require a manual connection to a junction box on the outside of my house to complete the circuit. That way, I can argue that the electrical connection is only temporary and is little more than a safe and buried version of an extension cord.
Learn basic principles of working with wood while making your own carved wooden spoon. Topics covered include different types of wood, grain direction, carving, shaping, and food safe finishes. Through short demonstrations and lectures, we will use a combination of power and hand tools, exploring the material for its functionality as a creative medium. At the end of the workshop, students leave with a unique spoon, ready to use! All materials included.
If you remember, when drilling the MDF I finished the holes from the other side using a Forstner bit. It made for a clean hole, but the positioning wasn't as precise as I really wanted. So for this, I decided to clamp a length of scrap MDF to the back side, and to drill straight through. My Forstner bits were too short, so I bought an extender. And then I found that the spade bits I was using gave a cleaner exit hole. Whooda thunk?

I love the opportunity Community Woodshop provides to take advantage of the tools, high-end equipment and hands on skills they'll assist you with when working with woods and metals. I'm not too sure about the Community part because I'd probably not come back because of the distance, however I do recommend learning to build shit on your own rather than paying a hefty price for the same materials that all furniture and fixtures and most jewelry are made of. They offer a wide variety of classes that teach you skills to build different items and use different tools.
The Classic Workbench is based largely on the famous Plate 11 workbench from Roubo’s “The Art of the Joinery”. We’ve built dozens of these “Roubo” benches over the past decade, helped others build hundreds more and examined extant French benches from the period. We haven’t changed our opinion on this fundamental design. French technical schools of the late 19th and early 20th centuries were outfitted with benches of the exact type. And prior to the 1950’s, you could easily buy a “Classic” workbench from any number of French supply houses. Benchcrafted continues the tradition by offering this excellent workbench, built in Iowa with American hardwoods to the highest standards.

Having done all this, I'm not sure I'd do it this way again. It might well be faster to layout the positions with compass and straightedge directly onto the top. Either way, you'll want to use a scribe rather than a pencil. Scribe lines are hard to see, and impossible to photograph, but the scribe and compass points click into them, allowing a precision that pencils simply cannot match.


I am sharing here a link to the detailed tutorial written by Pete at diypete.com, who shares the step by step process for making a wonderful barrel coffee table from scratch. He also tells you what items you’ll need for this project and where to find them. For example, you can buy an old whiskey barrel online or from a local whiskey store for a few bucks, if you haven’t already got one.
2 - use a plunge router with a bottom bearing cuter bit such as this from rockler: http://www.rockler.com/product.cfm?page=25160&site=ROCKLER .... I thought to use the short one as I plunge it directly downward in the centre of the hole until the bearing reaches within the tabletop hole. I suppose one could use a long one, but the stubbiness seemed more practical (the big bearing ensured accuracy?)
I ended up making a number of practice cuts. The first revealed that I hadn't tightened the screws on the edge guide enough. The second revealed that the design of the edge guide provided very little support at the end of a board, because of the cut-out for the router bit. In the "Getting Started in Woodworking" video, they had screwed a piece of hardwood to the edge-guide, to provide a continuous -- and longer -- bearing surface. I may do that myself, some day, but I didn't have the materials at hand, so I clamped some 2x4 scrap to the end of each board, to provide a continuous bearing surface past the ends. The two grooves in the long stretchers and the side groove in the short stretchers have identical layout. I made practice cuts in scrap until I had the edge guide set correctly, then I cut them all with that one setting. The bottom groove of the short stretchers uses a different setup, so it was back to the scrap, before cutting them.
This class is open to novice woodworkers and to more experienced woodworkers who would like to broaden (or simplify) their approach to woodworking. What do we mean by novice? We think it means you are a person who has decided to commit to learning new skills; to growing a passion for the craft of working with wood; and has a strong sense of the limitations of your own knowledge.
Not sure about Midwest but I have a 24 x 14 Game rm attached to my shop and I put a small window unit/heat pump in the wall. It stays comfortable all year round. It get really hot here and we had a several day in the 20's this winter but it's insulated well. That might not be as cold or as hot as in some places but the unit I haze does not run that often and has a low cost rating. I'm planning on putting a larger unit in the shop area even though I do like to work with the garage door open. The door is insulated so I can run A/c in there. Just my .02.
Next is the shelf. Start with the 24x48" piece of MDF. Clamp this on top of the base, and pencil in the outside of the stretchers and the inside angle of the legs. Flip it over, pull out your trusty cutting guide, and cut it to width and to length. Cutting out the angles is simple, with a jig saw. It's not much work with a hand saw. If you took enough care with supporting blocks and stops, you could probably do it with a circular saw. Since I did have a jig saw, I used it.
The reason I'd cut out the rectangles in the vise support was that I'd intended to put a benchdog hole through each, and I wanted the thickness of the top to be the same for all of the benchdog holes. Where I messed up was in not cutting out the ends, between the bolt tabs. I'd intended to put a benchdog hole through there, as well, but I'd forgotten to cut out the segments prior to glue0up.
Even with all of those faults my only regret is that it is too ugly. I didn’t take the time to make it more visually attractive as I was eager to get right into making beautiful furniture instead. Twenty years later the furniture is still beautiful (or not) but I go out to the shop and look at a drab uninspiring workplace. Yeah, nothing wrong with having a visually inspiring workplace in my opinion. All that shop furniture I slapped together years ago with no concern about aesthetics is getting replaced bit by bit. Why should my shop be downright ugly when it is one of my favorite places in the world to spend my time? I see no reason for that, but that’s just my opinion and as we all know everyone has their own one of those… Sadly, no one pays nor reveres me when I offer mine. bummer, I could be a rich egotistical maniac if they did coz I sure offer it enough. 😉
The first time you try your hand at the ancient craft of woodworking, you want to do it right. Learn woodworking basics with hand tools to a professional standard on a weekend woodworking course at Rowden Atelier. Ed Wild runs weekend furniture building courses for everyone from beginners who want to have some fun experimenting behind the bench, to those who are looking to develop specific skills as a furniture maker. Classes include tool handling, box making, and basic veneering, but to a certain degree, you can tell us what you want to learn - these short woodworking courses are partly bespoke.

Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.

Thanks! Great information. As an advanced novice worker, I finally decided to build my first bench a couple years ago. After reading several of your blogs knowing full well mortised dove tale leg joinery is yet beyond my capability, I elected to build Robert Lang’s “21st Century Workbench”. I also chose his VERITAS Twin Screw Vise in the face vise position. Used an old Craftsman face vise in the tail vise position. Constructed of laminated 9/4 x 31/2″ Pecan and 60″ long because of my small crowed shop. Super happy to this point. As I mature in woodworking I may live to construct one of a different choice at a latter date, but I’m 73 so we’ll see. Thanks again for the advise.
I’m building my second bench. I built the first years ago with wood from old machinery pallets – mostly oak and maple. Mortised the legs into the base, and pegged ’em with 1″ dowels. Of course, the legs warped a bit, but that made everything tighter and stronger. The top is 2″ thick Ash, one board cut in half and joined side to side. Wrapped a maple apron around the top, and I think I screwed the top from underneath to the leg braces. Solid. Over time, built a cabinet under for 3 drawers and a small cabinet door. Works for me.
My first attempt at making a cutting guide didn't work. What I ended up with worked fine for cutting panels, but the guide-strip was too narrow, and when the saw was extended fully for rough-cutting the 4x4's the clamp heads got in the way. So I made another. Actually, I made two more, so that I could cut one into shorter pieces that would be easier to handle.

I can't recommend this place highly enough. As someone who wants to test the waters in the hobby of woodworking this is the perfect place. They have all of the tools you need to complete your project, and they are great with helping beginners. I began as a skeptical customer but the staff was super ready and willing to make sure we could rectify a misunderstanding.
In this class we will explore the works of one of my favorite woodworkers, George Nakashima. This chair has elegance, simplicity, subtle details, and beauty. Don’t let its simplicity fool you. This chair requires great skill and precision to execute. It involves carving and sculpting of the seat with power and hand tools. The complex joinery has...
Working with wood fresh from the log, this green woodworking project is the perfect introduction to edge tools and wood grain.  In the first week you will produce a three-legged stool using buck and “whip”saws for crosscutting the log to length; wedges and froes for splitting out leg stock; drawknife and spokeshaves at a shaving horse for shaping the legs; and using travishers, rounding planes and specialized rasps for shaping the seat.
Palomar Community College in San Marcos, located about 35 miles north of San Diego, offers certificate, degree and life-long learning programs to more than 20,000 students a year. In particular, the Cabinetmaking and Furniture Technology Department offers in excess of 50 classes annually, and the present faculty is composed of four full-time teachers, 21 part-time instructors and 11 teaching assistants. As of Fall 2013, woodworking students will have access to a newly remodeled woodworking facility equipped with three machine rooms, three bench rooms, a saw mill and a finish room.
Timberframing is a traditional technique for building large and small structures using only wooden joinery. Prized for its structural integrity and beauty, as well as reliance on hand skills, timberframing is regaining popularity in modern applications. We will start with an overview of the different styles and aesthetics involved, and move into the specific tools that are used to lay out and cut the strong joints. Each student gets guided practice time making sample joints. We will all work together to make a small structure that can be raised on the final day of class.
In ancient times, the woodworker’s bench consisted of a plank or split log with four splayed legs. Descendants of those benches are manufactured today, usually with a top of hardwood slabs glued together. The norm nowadays is four straight legs supporting the bulk above, often with braces and a shelf below. Despite the improvements, the linkage to Greek and Roman antecedents is still evident.
Right now, there is a revolution in woodworking courses created by the closure of many state-run colleges. Our workshop has led the way and been the model for many of the private furniture making courses available to you today. Rowden Atelier is recognised as a Centre of Woodworking Excellence that produces exceptional furniture and trains exceptional woodworkers. With our range of specialist woodworking courses, you could be one of them.
The bench I will be describing differs from both of these in a couple of areas, the most significant of which is the top. Allen's top was made from three layers of 3/4" medium density fiberboard (MDF), topped and edged with 1/4" hardboard. Christiana's top was just two layers of 3/4" MDF. My top is two layers of 3/4" MDF edged with 1/2" oak and topped by a 1-1/2" thick edge-glued oak Ikea countertop. My top is more expensive in both time and money than either Christiana's or Allen's. If you're looking to build something fast and cheap, I'd recommend Allen's approach over Christiana's. The hardboard significantly increases the durability of the top.
1. You mention doing other hobbies which I assume means stuff scattered around for various projects. (Don't tell me you do one at a time or are a neat freak!!!) How tall are the side walls to the shed? How high do you shuffle stuff around, i.e. flipping things over, moving wood around, etc? I can't imagine trying to do that in my shed, even if it were 2 ft higher than it's 7 ft center height. If you could build a platform in front it may help, especially if you can put removable cover over it (to please HOA).
×