The jaw for the front vise needed to be 10" long - to span the distance from the leg to the end of the top, 1-1/2" thick - to allow for benchdog holes to be drilled in it, and 5" tall. The end vise was mounted 3/4" lower than the front vise, and the screw and guide rods were thicker, so its jaws needed to be at least 6-1/2" tall. Again, they needed to be 1-1/2" thick to allow for benchdog holes, and 23" long to span the width of the bench.

Requirements and electives for the certificate and degree programs in cabinet and fine woodworking include an advanced cabinetry lab and a course in Euro-style hardware. Students in both the construction and cabinet programs can also learn about business contracts, receive training in computer technology and participate in a cooperative work experience.


The Community Woodshop allows me to have access to a countless number of the best quality tools in the industry. They are always on top of keeping everything working and running.  If anything breaks they are always very proactive in fixing things ASAP.  They also have more than enough tools so I never have to wait to use a sander or any of the smaller tools, and I have never had to wait more than a few minutes to get on the table saw (and even that is rare).
You're not the first person to say this! I'm half inclined to use the Lowes shed as a starting point for my own design. But I do think I'd feel better if I could work as an "aprentice" next to an "old master". Someone at work is going to put me in touch with a guy who builds sheds for a living, and apparently he's competitive with the prices @ Lowes and HD. The Lowes shed comes with a "Handman Package" that I don't want but would end up paying for, anyway. The "workbenches" were laughably flimsy.
We're planning to have a tree cutting service come in and take out a couple of diseased trees in the back part of our lot and then hire someone else to dig out the stumps. These trees are at the base of a small rise, and we're thinking about cutting into the "hill" a little bit and making a low retaining wall, maybe 18" to 24" high. But that's just intended to move the shed back a bit from the house. (Our total lot size is only 5,616 feet with an 1,800 square foot house.) Landscaping change like this won't affect current drainage patters, but anything else might make it worse.
I was using 2-1/2" coarse Kreg pocket hole screws. Kreg screws are supposed to be self-tapping, but the coarse-thread screws are intended to be self-tapping in softwood, and the fine-thread screws they intend for use in hardwoods aren't available in 2-1/2" lengths. I decided to drill pilot holes in the oak. Just to make sure, I did a test hole in the scrap piece I'd cut off.
At Costco, we understand that when you’re looking for a shed or barn, you’re not just looking for a space to store your tools, you’re looking for a structure that’s reliable, sturdy, and weatherproof. This kind of quality assurance is especially important when your shed or barn isn’t just a toolshed, but a place for storing your memories or working on projects. At Costco.com, you’ll find sheds and barns of all shapes, sizes, and materials. Shop by brand, color, or features, and rest assured, knowing that whatever structure you choose, you’re getting it at the best possible price!
Stop it. Really. I mean it. Pick a height between your thigh and waist that seems right. You’ll adapt. Don’t worry about your back. You’ll adapt. If you are really uncertain, make it a little taller and then cut down the legs. After a decade or so, your work habits will put a magic number in your head. You’ll have built enough furniture that you will know your number. Until then, pick a number.

Right now, there is a revolution in woodworking courses created by the closure of many state-run colleges. Our workshop has led the way and been the model for many of the private furniture making courses available to you today. Rowden Atelier is recognised as a Centre of Woodworking Excellence that produces exceptional furniture and trains exceptional woodworkers. With our range of specialist woodworking courses, you could be one of them.
1. You mention doing other hobbies which I assume means stuff scattered around for various projects. (Don't tell me you do one at a time or are a neat freak!!!) How tall are the side walls to the shed? How high do you shuffle stuff around, i.e. flipping things over, moving wood around, etc? I can't imagine trying to do that in my shed, even if it were 2 ft higher than it's 7 ft center height. If you could build a platform in front it may help, especially if you can put removable cover over it (to please HOA).

I’m building my second bench. I built the first years ago with wood from old machinery pallets – mostly oak and maple. Mortised the legs into the base, and pegged ’em with 1″ dowels. Of course, the legs warped a bit, but that made everything tighter and stronger. The top is 2″ thick Ash, one board cut in half and joined side to side. Wrapped a maple apron around the top, and I think I screwed the top from underneath to the leg braces. Solid. Over time, built a cabinet under for 3 drawers and a small cabinet door. Works for me.

The top is supported by the top ends of the legs and the top sides of the top stretchers. Stand your legs on end on a flat surface (like my door) and see if they wobble. If you have an end that isn't quite stable, use it as a foot, where the leveler will make it's flaws unimportant. Check the top edge of each stretcher for straightness. If one has a bit of a bow, use it for a lower stretcher. It's less critical that the shelf be well supported along its length.

In general, students in the certificate and degree programs learn how to understand and create their own shop drawings and design custom cabinetry. In the process, they also find out how to use the same tools and machines employed in the woodworking business and assemble cabinets according to industry standards. Additional program topics include the use of contemporary hardware in design.


Every piece meets the highest grading standards for Every piece meets the highest grading standards for strength and appearance. This lumber is for a wide range of uses from framing of houses to basic interior finishing applications. Boards can also be used for carpentry hobbies furniture shelving and general finish work. This lumber can also be used in ...  More + Product Details Close
Working with reclaimed wood is a savvy use of resources, and the material's country appeal is undeniable. With just a saw and a small drill, you can reuse old fencing to make these simple woodworking projects: picket-inspired picture frames. Finish them off by hot-gluing clothespins or bulldog clips to hang your prints. Here’s a step-by-step guide.
If you're using drywall screws, you'll want to countersink the holes. Drywall screws are flat-head, and need a countersink to seat solidly. If you're using Kreg pocket screws, the way I did, you won't want to counter-sink the holes. Kreg screws are pan-head, and seat just fine against a flat surface. Both drywall screws and Kreg pocket screws are self-threading, so you don't need pilot holes in the second sheet of MDF.

This is one of those things that you never know you need unless you have one. This amazing wooden sofa sleeve works perfectly on either or both sides of a sofa set. It gives your sofa a nice look. The sleeve can also be modified to include a cup holder, mobile holder, etc. You can easily find this item on any online furniture store, but an even better idea is to build one. This way, you can make a sofa sleeve design that you actually like and make space for cup and other things.
When you're working with linseed oil, never -- I mean NEVER -- leave used rags lying around. Hang them up outside, away from anything combustible, and where there's enough air circulation to keep them cool. Or put them in a bucket of water, and hang them outside later. If you're just setting a rag down for the moment, set it out flat, without folds, on something non-flammable. Hanging outside in the breeze, the oil in the rags won't retain heat while they oxidize. For the oil to completely oxidize can take in a couple of days, if it's warm, or more than a week, if it's cold and rainy. When fully oxidized, the oil will be solid and the rags will be stiff. At that point, they're safe, and can be thrown in the trash. Toss them in the trash before that, and you might as well say goodbye to your garage.
The description below is an outline for how the course will proceed.  We intentionally maintain a level of flexibility in our curriculum to adapt and respond to the needs of each group of students depending on aptitude.  Each project has a basic standard of completion as well as design opportunities for elaboration and exploration of more advanced techniques.   Our instructors will guide you through projects as is best suited for your ability level.   
I got this idea from a Pinterest post. The final product looks so beautiful that I just couldn’t wait to make one for myself. This was somewhat a different experience from my other regular DIY projects as it doesn’t involve making something from scratch, but turning an existing wood piece into another one. Nonetheless, I enjoyed it very much and the final product was very satisfying. The tutorial I used is linked below.
2 - use a plunge router with a bottom bearing cuter bit such as this from rockler: http://www.rockler.com/product.cfm?page=25160&site=ROCKLER .... I thought to use the short one as I plunge it directly downward in the centre of the hole until the bearing reaches within the tabletop hole. I suppose one could use a long one, but the stubbiness seemed more practical (the big bearing ensured accuracy?)
Learn to use hand and power tools to shape wood into objects that will last for decades. You’ll learn about the properties of lumber, safe tool use, measurement and layout, and fundamental woodworking joints. At the end of this week-long course, you’ll leave with an end-grain cutting board, a mitered corner box, and the skills to build an unlimited range of wooden objects.

Windsor Design is an interesting brand in that it is not actually its own company. Instead, Windsor Design is one of the in-house brands sold by Harbor Freight. While it may be a store brand, that should not dissuade you at all as Harbor Freight is known for selling some of the best products available for all fields of construction. Granted, this may not strictly be the best table available, but it does provide a solid mix of features to make it a good value.


I know, if you had a workbench, you wouldn't be building a workbench. Even so, you'll need some sort of work surface, even if it isn't as stable or capable as a proper bench. The traditional solution is to throw a hollow-core door over a couple of saw horses. The advantage of hollow core doors is that they're flat, stiff, and cheap. I used a folding table and a hollow core door I had bought for a future project.
PS:  I saw that a recent review from Nicholas L. hinted that some people weren't welcome at the Community Woodshop. I can say with absolute certainty that everyone I've met has been welcomed with open arms and encouraged to participate at the woodshop. My class is a mix of genders and races, and nobody has experienced any difference in treatment from Bob or anyone else there. I truly can't imagine a situation where anyone would be treated any differently.

You can transfer a graphic on any wood piece of your choice, including a frame, top of a table, etc. The surface should be clean and big enough for the graphic paper. I am also sharing a video tutorial here that explains in detail the process of transferring any graphic to a wooden surface using a freezer paper. Just gather the items you need and follow this video to carve your favorite designs on your favorite wood items.
If you're using drywall screws, you'll want to countersink the holes. Drywall screws are flat-head, and need a countersink to seat solidly. If you're using Kreg pocket screws, the way I did, you won't want to counter-sink the holes. Kreg screws are pan-head, and seat just fine against a flat surface. Both drywall screws and Kreg pocket screws are self-threading, so you don't need pilot holes in the second sheet of MDF.
Regardless of which type of screw you use, you'll need to flip the panel and use a countersink drill to on all of the exit holes. Drilling MDF leaves bumps, the countersink bit will remove them, and will create a little bit of space for material drawn up by the screw from the second sheet of MDF. You want to remove anything that might keep the two panels from mating up flat. I set a block plane to a very shallow bite and ran it over what was left of the bumps and over the edges. The edges of MDF can be bulged by by sawing or just by handling, and you want to knock that down.
We have 4 newly expanded Classrooms, 3 state of the art labs with over $275,000 of new machinery, and $600,000 spent on new exhaust and compressed air systems. We have 4 new CNC production machines, a Haas VF-3 CNC Router and a NEWCNC 4×8 multi head machine and 2 Laguna IQ Routers. Even our shop stools (with cushioned backs) are brand new. We have new course offerings such as our Computer Design Sketchup Class and 8 new Certificate Programs you can choose from.
Post Woodworking’s Hampton shed is a major standout in design. The sleek farmers porch immediately draws the eye into its pure New England charm and provides the utility of shade and a cool place to sit and enjoy a cold one. Like all of our sheds, the six-panel doors which add to the structure’s aesthetic come standard. They’re made out of fiberglass to last through many decades out in the elements.
×