The projects in this course follow a natural progression of skills, techniques and tools. Some of the early student-made tools are, in fact, used to help make the next tool or bench fixture in the series. You are supported in the building of these projects with step-by-step outlines, knock-down examples and continuing, one-on-one consultations with the faculty. Periodic evaluations of your progress with a specific faculty-mentor help keep you on track.
Then I flipped the top and the base, lied up the base in the proper location relative to the top, I then positioned the front vise and the support MDF for the end vise, and marked the locations of the bolt holes. Then I flipped the base right side up, drilled small pilot holes from the bottom side where I had marked the locations, and then drilled shallow countersink holes from each side, then a through hole that matched the bolts. Finally I tried out the bolts and washers, and deepened the countersinks until the heads of the bolts were just below flush.

I’m building my second bench. I built the first years ago with wood from old machinery pallets – mostly oak and maple. Mortised the legs into the base, and pegged ’em with 1″ dowels. Of course, the legs warped a bit, but that made everything tighter and stronger. The top is 2″ thick Ash, one board cut in half and joined side to side. Wrapped a maple apron around the top, and I think I screwed the top from underneath to the leg braces. Solid. Over time, built a cabinet under for 3 drawers and a small cabinet door. Works for me.


My name is Takami Kawai and I'm a traditional Japanese carpenter and architect with over 16 years of experience in sustainable design and construction. As much as conditions allow, I enjoy using traditional Japanese techniques. My experience includes working for the world renown, Ise Jingu Grand Shrine. I have also hosted numerous presentations on traditional Japanese woodworking. Now, I run a small construction firm, Suikoushya, which specializes in the restoration of traditional Japanese houses.
This place is so awesome. I just finished their cutting board class with Bob and it was a blast! he was very patient and informative. I showed him a handle I saw online and he actually helped me do it with my board and we ended up going over time of the class and I learned a ton (thanks bob!! You are the best!) I also took the wooden utensils class with tim and it was so much fun. I highly recommend this woodshop everyone there is so nice and down to earth
The Handy Home Products Berkley 10 ft. x The Handy Home Products Berkley 10 ft. x 10 ft. Wood Storage Building Kit with Floor is made with factory-primed SmartSide siding to resist fungal decay and wood-destroying insects. The Berkley’s gambrel style roof provides plenty of height to add a loft for extra storage space. The 6 ft. high ...  More + Product Details Close
Through demonstrations and practice you will learn how to build a Simple Table Top. Square wood using the Jointer, Planer and Table Saw, then learn how to use the Festool Domino Joiner to keep perfect registration during the glue up. This will be a group project where everyone will help build a single table top. The goal is to gain experience and confidence...
My bench is MY BENCH. In other words, it’s a thing of evolutionary beauty. I built the top 10 years before deciding on and designing the base. I spared no absurdity. It is supremely stout and the much maligned drawers are accessible from either side. The larger drawers have dust lids and can be extended to provide support for large workpieces or as a step for climbing on top of the bench. The top alone weighs more than most Roubos. So NYAH! Did I mention that I designed it to fit in with the Arts & Crafts vernacular? Who said you can’t build your bench to be furniture? Beautiful as well as useful shop furniture? Just sayin…
Those bums even have a stipulation that you can't connect any utilities to a shed. My plan is to adhere to the letter of the law if not the spirit. I plan to run a buried 20 amp power line out to the shed (this will be done professionally and properly according to whatever is required by the law), but it will require a manual connection to a junction box on the outside of my house to complete the circuit. That way, I can argue that the electrical connection is only temporary and is little more than a safe and buried version of an extension cord.
Get perfectly, consistently spaced and centered shelf-pin holes! Economical and practical, this jig can be used on assembled or unassembled cabinetry. Re-designed handle includes two storage compartments for self-centering bits! Ideal for adding shelves to new or existing cabinets. Drills holes either 1-7/16" or 2-1/2" from edge. Insert shelf pin in top or bottom position to extend jig for continuous drilling. Shelving Jigs measure 20" long Additional Self-Centering Bits available. 

Quality is what we do, YOU will do it too, from day one. We will teach you all stages from choosing hand tools, to picking out wood, to developing your drawings, and building a portfolio of work. There are lots of workshop schools, courses, and magazines that are great for showing you an amateur way of getting a good result. An amateur has no excuse for poor work other than lack of understanding, the amateur has all day to get it right, the professional has not. They must do it right, first time, every day.

to allow 9' at the peak, I like a "shed style" roof, but that may not fly in your HOA.I'd put double doors on or one large one, pour a slab, or use patio blocks then lay down Wolman. plywood for a floor, I would use foam insulating board everywhere I could, walls, floor and ceiling. A few bin type windows or sliders would let in light and fresh air. If you can't get away with your wiring idea, I would use a HD 30 amp twist lock extension cord with an "outside weatherproof outlet" mounted on the home professionally installed for code, 2- 8' long flouresent lights, and a 20 amp outlet inside for a heater and dehumidifier. Dehumidifiers draw about 5-6 amps. You might be better off with a small 6000 BTU window or wall mounted AC unit,( $100 on sale at the Depot), it will take the moisture out of the air and cool it as well in the summer. I'd use thin wall conduit around the shop with about 4 double duplex boxes. You may be able to bring 220v. in and then split into 2-120v circuits. If you make ANY dust in this confined space you must first catch it with a shop vac, then filter the air, and wear a mask. A bathroom ventilator fan would exchange the air and be quiet. A slab in front would allow sawing outside weather permitting. A roll up canopy over the door way would provide "shade" and rain protection. I know this sounds like a lot of work, but I know you can do it if you try. You can get plenty of "free" advice here and from an expert close to you. My neighbor enlisted the help of a handyman for building his 2 sheds and they became friends and did tool swaps and labor trades for time worked. My advice to you.. go 4 it! bill


We're planning to have a tree cutting service come in and take out a couple of diseased trees in the back part of our lot and then hire someone else to dig out the stumps. These trees are at the base of a small rise, and we're thinking about cutting into the "hill" a little bit and making a low retaining wall, maybe 18" to 24" high. But that's just intended to move the shed back a bit from the house. (Our total lot size is only 5,616 feet with an 1,800 square foot house.) Landscaping change like this won't affect current drainage patters, but anything else might make it worse.
×