AJ and Scott have been very helpful showing me where tools are my first few days there. This is a workshop where you will have to work independently. They will show you how to use certain machines for the first time and orient you to the shop itself but they will not help you with your project.  They can, however, be hired to help you with projects if that's what you need. I believe it's $75 an hour and limited to their availability. There is also a host of classes you can take if you want an intro into cabinet making, wood joining, turning etc. There are a lot of different classes that may pique your interests.
A better solution would have been to route a rabbet into the side, so that the added strip always had thickness. The way I did it means that the strip I glued in is very narrow, and hence very weak, at a certain point. In this case, that's not a problem, because it's going to be sitting under the countertop layer. I also noticed that because I had only clamped the strip down, and not into the edge, there was a noticeable glue gap where the strip butted up against the MDF. Again, in this application it isn't visible. But if I was doing something like this on the top of a table, I'd make sure to cut a clean rabbet, and to clamp both down and in.

Cerritos College in Norwalk serves over 21,000 credit students each year with certificate and degree programs for recent high school graduates and adult learners. The Cerritos College Woodworking school is housed in 27,000 square-feet of space and is equipped with over 100 woodworking machines. Under the direction of 20 instructors, the school offers more than 50 classes in woodworking, including those in architectural millwork, cabinet and furniture making, routing and veneering.

Working with reclaimed wood is a savvy use of resources, and the material's country appeal is undeniable. With just a saw and a small drill, you can reuse old fencing to make these simple woodworking projects: picket-inspired picture frames. Finish them off by hot-gluing clothespins or bulldog clips to hang your prints. Here’s a step-by-step guide.
A bottle carrier is a bucket like carrier used to carry beer bottles and so. Yes, the same one you must have used to carry your six-pack. Drinker or not, a bottle carrier is a useful item for everyone. It can be used to carry around or store small items around a household. And it is also very easy to build one. I have several of these lying around my house. Also known as wooden beer totes, this is one wood item you will absolutely love to make. It is also super easy to build.
Assemble the vises, for the final time. You'll not be taking them off again, so tighten everything down, and attach the endplate to the ends of the screw and guide rods. Then mark and drill benchdog holes in the outer jaws inline with the benchdog holes in the top. Generally, through-holes are preferred for benchdogs, so that they don't collect sawdust and gunk. With these vises, that isn't possible, there are screws and guide rods in the way. I drilled them just deep enough to hold a Veritas Bench Pony (their reduced-height benchdog), without it sinking to where I can't get a grip to remove it. Rockler sells some very inexpensive plastic benchdogs that can't be adjusted for height, and aren't as strong as metal or wooden dogs, that I intend to keep in the holes full-time, to keep sawdust from collecting in them.
Learn to use hand and power tools to shape wood into objects that will last for decades. You’ll learn about the properties of lumber, safe tool use, measurement and layout, and fundamental woodworking joints. At the end of this week-long course, you’ll leave with an end-grain cutting board, a mitered corner box, and the skills to build an unlimited range of wooden objects.
I can't recommend this place highly enough. As someone who wants to test the waters in the hobby of woodworking this is the perfect place. They have all of the tools you need to complete your project, and they are great with helping beginners. I began as a skeptical customer but the staff was super ready and willing to make sure we could rectify a misunderstanding.

The decision to be made with respect to the end vise is whether the support plate should be mounted to on the inside or on the outside of the stretcher. Mounting the plate on the inside of the stretcher reduces the reach of the vise - it can't open as far, because the support plate is back from the edge by a couple of inches. But mounting the plate on the outside of the stretcher means that we need to add some support structure for the inner jaw of the vise, which the legs would have provided if we'd mounted the plate on the inside.
Laney College is located in Oakland near the San Francisco Bay and currently enrolls around 12,000 students. The Wood Technology Department offers 1- and 2-year certificate programs in wood technology, computer-aided drafting and design, as well as an apprenticeship program and carpentry courses. Students have access to eight faculty members and a variety of woodworking machinery and equipment, including a lathe.
The first time you try your hand at the ancient craft of woodworking, you want to do it right. Learn woodworking basics with hand tools to a professional standard on a weekend woodworking course at Rowden Atelier. Ed Wild runs weekend furniture building courses for everyone from beginners who want to have some fun experimenting behind the bench, to those who are looking to develop specific skills as a furniture maker. Classes include tool handling, box making, and basic veneering, but to a certain degree, you can tell us what you want to learn - these short woodworking courses are partly bespoke.
For one, the bench itself is a good size. While its width as a tad short at just over 1 ½’, the length is a great 5’ long. Even better, this bench is made out of birch wood. Birchwood is similar to beech in that it is strong but soft enough to prevent inadvertent dulling of your tools. However, birch has a bit of an advantage over beech in that it is not a porous which makes staining on the Windsor Design a more worry-free affair.
I drilled from the mark. That way I could ensure that the hole was where it was supposed to be, on the side where the position was critical. I have two 3/8" bits -- a brad point bit that came with my doweling set, and a perfectly ordinary 3/8" twist bit. Brad-point bits are far more precise than twist bits -- they're more likely to start where you want them to, and they're more likely to stay straight. My problem is that my brad-point bit wasn't long enough to go through 3-1/2" of wood. So I started each hole with the brad-point bit, then finished it off with the twist bit. I clamped a piece of ply on the back, to reduce tear-out.
The tutorial that I am sharing here was written by someone who built this pallet art just to improve the value of a property they wanted to sell fast and they succeed in it. So you can imagine how wonderful this item must look like. I am assuming you do not just want to make this beautiful pallet art so that you can also sell your property easily. Well, whatever your reasons are, this beauty is able to attract anyone who visits your house.

This is for the serious amongst you. Those of you who are ready to make a change in your life. To really surround themselves with woodworkers and furniture making for a whole year. Not only do you get to learn some great traditional skills but also drawing, the beginnings of design and how to run a woodworking business successfully. This intense workshop training gives you a good foundation to make your own way to become a furniture maker.
Frame making may look simple but it is a skill that escapes many. For a frame to properly do its job it has to be perfect, any mistake can be a distraction that takes away from the artwork it surrounds. This class will focus on skills essential to making square or rectangular frames. Skill building concepts will include how to break down and mill...
The Meridian 8 ft. x 10 ft. wood The Meridian 8 ft. x 10 ft. wood storage shed kit from Handy Home Products is pre-cut and easy to assemble with common household tools. It features 9 ft. peak wall height with treated engineered siding that prevents rot and is pre-primed and ready to paint (paint sold separately). The ...  More + Product Details Close

I built my first platform bed by following the steps mentioned in the tutorial and the end result was everything I expected. It was as beautiful as comfortable and strong. It only cost me around $60 to build this one from the scratch. And if I can build it, anyone can. What you need is a little bit of woodworking experience and a lot of confidence. Collect the items as suggested in the video and start working now.


In class, each student will build a detailed hall table that is complete with mortise and tenon joinery, biscuit, dowel, and floating joint construction.  The student project is presented with a variety of design options and formats as to meet the experience and comfort level of each student.  Depending on their experience and comfort level, students are encouraged to make a simplified version of the hall table or tackle a more sophisticated and complicated version of the same project. Your only limitation is the amount of material you receive in your lumber pack (~24 board feet).

In this two day class we will reveal some of the secrets to tuning up a Japanese Hand Plane (Kanna) We will start with conditioning the Body of the Plane (DAI) to stabilize movement. Proper sharpening and grinding of the blade and chip breaker will be discussed and demonstrated. Custom fitting the blade to the Dai and conditioning the sole. We will...
I am blown away with their ability to teach, a rare characteristic in my opinion, even more so is their passion to do so. I feel that they are able to accurately depict the philosophies and ideas mentioned in your website. My expectations did not even come close to the actual experience I have been given, and that is only in a short short time! I can only dream of what the next 11 months will bring! I am convinced my decision to study at Rowden Farm is the best one I have made to date! Thank you! Much appreciation and gratitude!”
Something like this really does look like it would be a fun project. I guess I need to go out to the yard and use some stakes and brightly colored taped to mark off some different dimensions (12x8, 12x10, 12x12, etc.) to figure out just how big I can make this thing. If I'm building it myself, it'll be easy to keep the height right at the 9 foot limit.
×