The Classic Workbench is simple to use. The leg vise is used primarily for working the edges of boards and the ends of narrower boards. This is self explanatory. To work the faces of boards along the grain, tap up the planing stop (don’t make it any higher than necessary) and butt the end of the board into the teeth of the stop. With the right technique you can plane across wide boards without repositioning the board. You usually don’t need to tap the opposite end of the board to engage it with the stop, but in some cases, especially with rougher stock, you may need to give a tap with your mallet. Working the faces of a stack of boards is extremely quick with the planing stop since you don’t have to open and close a vise constantly. To work across the face of a board, make yourself a doe’s foot and position it at the back corner of the board, holding it down with a holdfast. The doe’s foot is simply a piece of wood with a V-shaped notch cut into one end. The bottomsurface of the doe’s foot can be lined with sandpaper or Crubber to help it stay put on the bench top. To work long boards, fasten a batten to the right leg with a holdfast and use that to support the end of the long board. We’ve found that a deadman is not necessary for the majority of work, especially on a bench of this length. For working the ends of smaller boards the leg vise can be used, but for precision work like dovetailing, we use and recommend our Moxon Vise.
I'd intentionally made it oversize, intending to trim it flush. Trimming is a little more complicated than usual, because I needed to trim it flush on two faces. The end face extended a good 3/8", so I cut off most of the excess with a circular saw and the edge guide, then flipped the edge guide upside down to make a stable platform for the router. Aside from the use of the edge guide, flush trimming the edge face was unremarkable.
As soon as I came across this tutorial, I didn’t wait any longer to start building one. Some of the items you need for this project are hardwood plywood, saw, glue, nails, drilling machine, etc. The video is very easy to follow for anyone with basic woodworking knowledge and experience. The first source link also includes a step by step procedure in plain English for those, who are not comfortable enough with the video tutorial.
I am new to woodworking. I'm learning as I go along, and I'm documenting as I learn, in the hope of being helpful to other novices. On the range from slap-dash to deliberate, my method is definitely on the deliberate side. If you have enough experience to be confident in using techniques that are more time-efficient, go for it. The techniques I'm using are those I thought least likely to go wrong, not those that would produce a product in the shortest time or at the lowest cost. You'll notice that I made a number of mistakes, spent considerable time on work I later determined to be unnecessary, and in a number of cases I used different techniques at the end than I did at the beginning. These are all the result of learning. I thought it would be better to demonstrate how I made errors, and how I corrected them, than to provide a set of instructions that presented the false impression that everything went together perfectly.
Requirements and electives for the certificate and degree programs in cabinet and fine woodworking include an advanced cabinetry lab and a course in Euro-style hardware. Students in both the construction and cabinet programs can also learn about business contracts, receive training in computer technology and participate in a cooperative work experience.
This trade and technical college currently serves over 15,500 credit students from its campus in downtown Los Angeles. Through the Construction, Design and Manufacturing Department, full-time students can enroll in a daytime certificate or an Associate of Science program in cabinet and millwork. Evening programs for current craftspeople include a certificate program in construction technologies and an Associate of Arts in cabinetmaking and millwork that provide students with the skills they need to work in construction or manufacturing.
Had a great experience at the shop! My schedule is hectic and unfortunately can't make the classes, but I did do a private lesson with Bob. In one afternoon, we created two cutting boards. Bob was very detailed with breaking down the process and using the machines. Honestly didn't expect to make two cutting boards but Bob was proficient with time. I got really comfortable using the machines especially the table saw. I learned how to use the planer, jointer, miter saw, table saw, drill press, router, disk sander, and random orbital sander. Really recommend folks that are interested in woodworking with little to no experience to take the Safety Orientation and the Cutting Board class or private lessons. Looking forward to my next project at the shop!
First, we need to drill out the holes for the screws that will hold them together. While the two layers of MDF are glued, the countertop and the MDF will only be screwed. The oak countertop, like any natural wood product, will expand and contract with humidity changes. If it were glued to the MDF, the difference in expansion of the two layers would cause the countertop to buckle and curl.