Architecture cabins Colonial Colonial architecture construction Decor design Eastern White Pine flooring Forest Facts forestry Furniture History Homes Houses Innovation Interior Design interiors Log Cabins Log Homes lumber Maine Massachusetts modern Monographs NELMA New England News New York pine pine architecture Residential Sculpture Skyscrapers sustainability Sustainable Forestry Technology timber frame trend watch Vermont wood Wood Architecture Wood Buildings Wooden Architecture woodworking

Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.

If the holes of the first jaw are in the proper position, drill holes in the same locations on the other jaw. I lined the drilled jaw on top of the undrilled jaw, clamped things down, and then drilled about 1/4" into the undrilled jaw, to mark the location. Then I removed the drilled jaw and drilled out the marked locations the same way I did the first.
In the "Getting Started with Woodworking" video, the holes through the 4x4's were drilled from the back. That is, they start on the side opposite the precisely-positioned mark, and drill through to hit it. If they can do this, more power to them, but I can't drill through 3-1/2" of wood to emerge at a precise mark without a drill press - and not always then.

ALL Red Kits require planing and jointing of wood. Red Kits require the skill and tools to cut and make joints including panels. The woodworker needs to be able to cut, join, assemble and finish. Red Kits require the woodworker to be able to read the plans and to transfer images and dimensions from the plan to the lumber. It supplies all of the needed hand-selected, dimensioned lumber but woodworking knowledge and tools are recommended to be successful with Red Kits.

Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.


I am new to woodworking. I'm learning as I go along, and I'm documenting as I learn, in the hope of being helpful to other novices. On the range from slap-dash to deliberate, my method is definitely on the deliberate side. If you have enough experience to be confident in using techniques that are more time-efficient, go for it. The techniques I'm using are those I thought least likely to go wrong, not those that would produce a product in the shortest time or at the lowest cost. You'll notice that I made a number of mistakes, spent considerable time on work I later determined to be unnecessary, and in a number of cases I used different techniques at the end than I did at the beginning. These are all the result of learning. I thought it would be better to demonstrate how I made errors, and how I corrected them, than to provide a set of instructions that presented the false impression that everything went together perfectly.
Thanks! Great information. As an advanced novice worker, I finally decided to build my first bench a couple years ago. After reading several of your blogs knowing full well mortised dove tale leg joinery is yet beyond my capability, I elected to build Robert Lang’s “21st Century Workbench”. I also chose his VERITAS Twin Screw Vise in the face vise position. Used an old Craftsman face vise in the tail vise position. Constructed of laminated 9/4 x 31/2″ Pecan and 60″ long because of my small crowed shop. Super happy to this point. As I mature in woodworking I may live to construct one of a different choice at a latter date, but I’m 73 so we’ll see. Thanks again for the advise.

One aspect of the Windsor Design that is hit or miss is the vice. Notice we have to use the singular when describing it because this is the first workbench that we have reviewed which features only one vice. To make matters more frustrating, the vice cannot be repositioned along the bench. That said, the vice does at least have the largest capacity out of any we reviewed. At 7” capacity, the Windsor Design vice can secure any size workpiece you may have.

Timberframing is a traditional technique for building large and small structures using only wooden joinery. Prized for its structural integrity and beauty, as well as reliance on hand skills, timberframing is regaining popularity in modern applications. We will start with an overview of the different styles and aesthetics involved, and move into the specific tools that are used to lay out and cut the strong joints. Each student gets guided practice time making sample joints. We will all work together to make a small structure that can be raised on the final day of class.
Constructed with the classic craftsmanship that Grey’s Woodworks is known for, our beautiful sheds come in a variety of styles, sizes and colors. We will help you design a shed to match your surroundings and meet your needs. Select from our pine tongue and groove, duratemp T1-11, or vinyl sidings and arrange doors and windows to your liking. All of our sheds are handcrafted in modern workshops. Not only does a shed from Grey’s Woodworks provide much needed storage space for your mower, snow blower or bike, but it also makes for an attractive addition to your property.
I like the idea of re-inventing the wheel. I choose to believe that while others may have considered these improvements, they just never got around to trying them out. Brain gets bored with status quo. So, I try to keep Brain happy with the occasional foray into uncharted territory. And I must say Brain has had some really good results. Thanks, in part, to you, and the Roy. You never know where a good idea might come from so I’ll check in once in a while. That and make sure to build it in Sketchup first.

These sorts of things are usually glued and screwed, but it's actually the glue that holds them together - the screws just hold everything tight while the glue cures. Screwing into hardboard or 1/4" ply is an exercise in futility, so I just used glue, and used my two 4x4's as long clamps. It would have been a bit easier, if I'd done this before I'd rough-cut the 4x4's, but it worked out.
If you decide upon construction lumber, you want kiln dry lumber. Green lumber will warp on you as it drys. Dig through the stacks and pick out the straightest, cleanest pieces. Generally, the boards that are sitting loose on the stack are those that other people left behind, as they sorted through looking for better. Be prepared to move them out of the way, and to dig down to the better stock. Be nice, though, and put everything back when you're done.
When you're working with linseed oil, never -- I mean NEVER -- leave used rags lying around. Hang them up outside, away from anything combustible, and where there's enough air circulation to keep them cool. Or put them in a bucket of water, and hang them outside later. If you're just setting a rag down for the moment, set it out flat, without folds, on something non-flammable. Hanging outside in the breeze, the oil in the rags won't retain heat while they oxidize. For the oil to completely oxidize can take in a couple of days, if it's warm, or more than a week, if it's cold and rainy. When fully oxidized, the oil will be solid and the rags will be stiff. At that point, they're safe, and can be thrown in the trash. Toss them in the trash before that, and you might as well say goodbye to your garage.
 I have always wanted to share this wonderful woodworking world with like-minded people from all over the world. For the last six months, I have started sharing Japanese woodworking information through videos and photos. Because of the huge amount of interest, I started organizing one-day workshops for people visiting Kyoto, letting them experience Japanese woodworking tools.
Making an art or a design on a wooden piece is a hectic task and requires good art skills. But there is another much easier way to carve a beautiful art on any wood surface. For this, you will need the image or graphic that you want to transfer, a piece of wood, freezer paper, etc. I, myself have made several such designs. At the source below, you can find a step by step guide for transferring a graphic image to the wood.
This table top is also made from the hardest wood out of any manufacturer we reviewed: oak. In fairness, this can be both a blessing and a curse. The oak wood is extremely durable and noted for its lack of a porous nature. This means the top can withstand plenty of abuse from tool and workpieces. Moreover, you will not have to worry about liquids like lacquers and stains from being absorbed into the top. That said, the hard oak can also do a number on tool sharpness, dulling them prematurely if they are not carefully handled.

The best thing about this wine rack is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can modify your wine rack any way you want or build in a design or color different from this one. The basic steps to build a wooden wine rack are the same for all variants. I have included here the video tutorial that I followed in order to build myself a pallet wide rack.
MATERIAL CONNECTION DISCLOSURE: You should assume that this website has an affiliate relationship and/or another material connection to the persons or businesses mentioned in or linked to from this page and may receive commissions from purchases you make on subsequent web sites. You should not rely solely on information contained in this email to evaluate the product or service being endorsed. Always exercise due diligence before purchasing any product or service. This website contains advertisements.

Be careful. Single 24x60" sheets of 3/4" MDF are pretty easy to lift. A doubled sheet is manageable. The countertop - 24x72" panel of 1-1/2" oak - weighs something over 100 pounds. It takes real care to lift safely. The joined top - 3" thick of oak and MDF - is past the range that can be lifted safely by one person. Don't try. Get a friend to help, or rig a block-and-tackle.

When you have the other leg seated, the threaded rods will extend father than you want them to. You'll want to mark them so they can be cut to length. Place a washer and a nut on each threaded rod, and then tighten down the nut to pull everything tight. Depending upon the wrench you are using, and how much longer the rod is than it needs to be, you may find it necessary to stack up a number of washers, so that the nut is positioned where the wrench can operate on it.
Get perfectly, consistently spaced and centered shelf-pin holes! Economical and practical, this jig can be used on assembled or unassembled cabinetry. Re-designed handle includes two storage compartments for self-centering bits! Ideal for adding shelves to new or existing cabinets. Drills holes either 1-7/16" or 2-1/2" from edge. Insert shelf pin in top or bottom position to extend jig for continuous drilling. Shelving Jigs measure 20" long Additional Self-Centering Bits available. 
It might not be the easiest project in this list, but if you already have some experience with wood cutting and joinery, it won’t be any hassle at all. Thanks to the extremely detailed instructions it shouldn’t really be a problem even if you’re not very familiar with woodworking. This could actually be a great project for refining your woodworking skills as a beginner!
Through demonstrations and practice you will learn how to build a Simple Table Top. Square wood using the Jointer, Planer and Table Saw, then learn how to use the Festool Domino Joiner to keep perfect registration during the glue up. This will be a group project where everyone will help build a single table top. The goal is to gain experience and confidence...
When we set out to design a new workbench for our customers, from the very beginning we decided it should, above all, be simple. We make no bones about it, our vises are designed and made to work sweetly, but not to a price point. However, not everyone is ready for a time-consuming bench build. For those looking to get their feet wet in traditional woodworking, using time-proven techniques and tools, this bench will provide all the workholding required to test the waters. For many, this will be all the bench you need, and for others it will be an excellent springboard to our Split Top Roubo, while keeping the Classic as a second bench. The bench features our Classic Leg Vise, Planing Stop and Crucible Holdfast as workholding devices. With a clever arrangement of our Planing Stop, Roubo’s Doe’s Foot and the Crucible Holdfast, you’re able to mimic the function of bench dogs and a tail vise, albeit in a more rudimentary manner.
For the router you'll need a a 3/8" straight bit, an edge guide, 1/4"- and 1/8"-radius roundover bits, and a flush-trim bit with at least a 1-1/2" cutting length. Bits of this size are available only for a 1/2" collet. Some routers are capable of using multiple collet sizes. I was fool enough to buy a router that only had a 1/4" collet. More on that, later.
A woodworking school teaching furniture making techniques located in Pennsylvania. Beginner through advanced students will learn solid wood furniture construction using traditional and modern techniques. The classes emphasize wood movement, practical methods, efficiency (with machines and hand tools), design, milling, joinery, finishing, and safety. Woodworking and furniture making courses are offered to aspiring crafts men and women throughout the country.
For your kitchen, it can work as a knife rack. It gives you easy access to all essential tools while saving space. In addition, it adds a nice visual appeal to your kitchen wall. You can customize your wall rack with different materials, designs and styles. I am here sharing the source link to the step by step tutorial about how to make a rustic wall knife rack.
The source above is not exactly a tutorial, but it gives you a basic idea of how the author built a Quirky Pallet Art to enhance the look of their old house. You can also find another tutorial at the link below. It shares a step by step procedure for making a wooden pallet sign. The final product is not exactly the same as the one above, but the basic idea is the same.
With the inner jaw fastened to the bench, I used the router to flush-trim the jaw to the benchtop, across the top and down the sides adjacent to the top (stopping short of the discontinuity between the top and the legs). I'd thought this would be the best way to match up the jaw against the top, but I'd not do it this way again. It was very difficult to hold the router tight against the face of the jaw, and the result was a surface that wasn't as even as I had hoped.
Although many hand tool operations are thoroughly covered, this is a machine based woodworking experience. You will find the school finely equipped with four table saws, four jointers, three drill presses, three thickness planers, a wood lathe, full dust collection, bandsaws, jig saws and scroll saws, 5 routers and dozens of router jigs and accessories. There is a heavy focus on the safe and efficient use of the table saw starting with it's basic operation and going into advanced production procedures. We consider the table saw to be an essential machine for efficient, accurate, and safe woodworking.

Require the woodworker to be able to read the plans and to transfer images and dimensions from the plan to the lumber. The wood has been planed and all glued panels are completed unless over 14 inches. If panel required is over 14 inches, one glue seam will be required. The woodworker needs to be able to do some cutting, jointing, assembling and finishing. White Kits do not require planing. White Kits supply all of the needed hand-selected dimensioned lumber, but woodworking knowledge and tools will be useful to complete the project successfully.

The Handy Home Products Berkley 10 ft. x The Handy Home Products Berkley 10 ft. x 10 ft. Wood Storage Building Kit is made with factory-primed SmartSide siding to resist fungal decay and wood-destroying insects. The Berkley’s gambrel style roof provides plenty of height to add a loft for extra storage space. The 6 ft. high side walls ...  More + Product Details Close

The reason I'd cut out the rectangles in the vise support was that I'd intended to put a benchdog hole through each, and I wanted the thickness of the top to be the same for all of the benchdog holes. Where I messed up was in not cutting out the ends, between the bolt tabs. I'd intended to put a benchdog hole through there, as well, but I'd forgotten to cut out the segments prior to glue0up.
Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.

Our instructors work out of a 27,000 square-foot facility, where over 100 stationary and portable woodworking machines are available. We emphasize hands-on training and real-world experience, and all classes are project-focused. Over forty different classes cover topics including faceframe and frameless cabinet construction, CNC woodworking, architectural millwork, table and casegood construction, hand tools, woodturning, and veneering.


For your kitchen, it can work as a knife rack. It gives you easy access to all essential tools while saving space. In addition, it adds a nice visual appeal to your kitchen wall. You can customize your wall rack with different materials, designs and styles. I am here sharing the source link to the step by step tutorial about how to make a rustic wall knife rack.
Some tools required for this project are hole saw, drilling machine, pencil, tape measure, clamps, etc. This tutorial explains every step properly with images so that anyone can make a wooden sofa sleeve easily. Those, who prefer a video tutorial, can visit the below link to a YouTube video that illustrates the process of building a DIY Sofa Sleeve Cupholder.
The edges of MDF are fragile, easily crushed or torn. MDF is also notorious for absorbing water through these edges, causing the panels to swell. In Sam Allen's original design, he edged the MDF with 1/4" hardboard. This edging is one of the complexities that Asa Christiana left out in his simplified design. I think this was a mistake. MDF really needs some sort of protection, especially on the edges.
Timberframing is a traditional technique for building large and small structures using only wooden joinery. Prized for its structural integrity and beauty, as well as reliance on hand skills, timberframing is regaining popularity in modern applications. We will start with an overview of the different styles and aesthetics involved, and move into the specific tools that are used to lay out and cut the strong joints. Each student gets guided practice time making sample joints. We will all work together to make a small structure that can be raised on the final day of class.

You are absolutely right on your advise. When I was agonizing over how to build a workbench my good friend turned me on to your book on workbenches. I was planning on having an overhang until I read your advise about building a workbench and not a table. So the entire front and rear surfaces; top, legs and bottom shelf are all in the same plane to clamp my work to. The addition of a sliding dead man was also something that I would have never thought of on my own. Thanks again for your advise.

Woodworking has a rich place in the history of human civilization. Used for thousands of centuries, it provided early cultures a way to construct shelters, furniture, boats, and more; in doing so, it made life easier and ultimately allowed a society to advance. The art of woodworking continues today, having survived a myriad of design aesthetics (including the not-so-wood-friendly Memphis Design). To pay homage to this ancient craft, one Instagram account called @wooodworking features pieces from different artists and artisans around the world.


A woodworker's Workbench is a special type of bench designed to hold your work when you are working on a wood project. The main purpose of this table is to keep the woodwork steady and to prevent it from moving. Follow the tutorial below to build yourself a nice workbench suitable for your specific woodworking projects. Make sure to modify the table to fit your specific requirements.

The Meridian 8 ft. x 10 ft. wood The Meridian 8 ft. x 10 ft. wood storage shed kit from Handy Home Products is pre-cut and easy to assemble with common household tools. It features 9 ft. peak wall height with treated engineered siding that prevents rot and is pre-primed and ready to paint (paint sold separately). The ...  More + Product Details Close

With my second attempt at edge guides, I made the other rough-cut. On this, the edge guide worked fine, but the end of the cuts revealed that the saw blade wasn't quite square. So I adjusted the blade, clamped all four legs together, and made what would be the first final cut, if it came out clean enough. It didn't. I'd let the saw drift a bit away from the guide edge. So I adjusted the saw, moving the guide back half an inch, and tried again. the rough-cut parts were a couple of inches longer than they needed to be, so I had room to work with,. It's only the final cut at the other end that you only have one chance at.
We have more than sixty years of excellence (1956-present) with an annual enrollment of more than 1,000 students in over 35 different classes.  The Palomar College Cabinet and Furniture Technology program offers the most comprehensive woodworking career curriculum in the nation. Utilizing three fully-equipped shops, our 2 full-time and 20 part-time instructors provide a breadth of courses and depth of expertise impossible to obtain in smaller programs.
Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.

Something like this really does look like it would be a fun project. I guess I need to go out to the yard and use some stakes and brightly colored taped to mark off some different dimensions (12x8, 12x10, 12x12, etc.) to figure out just how big I can make this thing. If I'm building it myself, it'll be easy to keep the height right at the 9 foot limit.
×