A shed is a great project to earn your sawdust legs on. It is just some very basic carpentry skills. You could build the whole thing with a circular saw, hammer, utility knife, pencil, and tape rule. Find a friend or relative that has some decent skills to help. You could do it in a weekend. Keep the size on a four foot increment to minimize wastee. I would recommend a 12 x 12 or a 12 x 16 if you can. If you don't want to cut any rafters (which is really a simple process), you can order small triangle shaped trusses for the roof from your local lumberyard. If you are using T1-11 for the sides, get the real plywood based stuff, no waferboard. Same thing for the floor, use plywood (treated if you like). Cedar for the trim, not pine. The visqueen underneath is a good idea. Insulate the walls inside to help temper temperature swings. Build overhanges into the roof all the way around, 12" is nice. These really are a fun project. You can add a small window with a flower box underneath to make it look a little homey too.
Put the upper panel of MDF on your glue-up surface, bottom side up. Put the bottom panel of MDF on your other surface, bottom side down. (The panel with the holes drilled in it is the bottom panel, and the side that has the your layout diagram on it is the bottom side.) Chuck up in your drill the appropriate driver bit for the screws your using. Make sure you have a freshly-charged battery, and crank the speed down and the torque way down. You don't want to over-tighten the screws, MDF strips easily.
You may even want to put yourself in the picture. If your workshop space already exists, find a large piece of cardboard, wallboard, or plywood that’s about the size of the workbench top you envision. Find a couple of stools or chairs, perhaps a few books, and turn them into stanchions to support the “benchtop.” Is it too big for the space? Is it large enough for the tasks you envision will be performed upon it?
With the inner jaw fastened to the bench, I used the router to flush-trim the jaw to the benchtop, across the top and down the sides adjacent to the top (stopping short of the discontinuity between the top and the legs). I'd thought this would be the best way to match up the jaw against the top, but I'd not do it this way again. It was very difficult to hold the router tight against the face of the jaw, and the result was a surface that wasn't as even as I had hoped.
A steam box and a heat source are the two main components used to steam bend wood. Steam boxes must be able to withstand large fluctuations in temperature and humidity without breaking apart. In this two-hour workshop, students will build an optimized steam box that can last through the tough job of steaming wood, allowing them to continue creating their own projects at home!
These sorts of things are usually glued and screwed, but it's actually the glue that holds them together - the screws just hold everything tight while the glue cures. Screwing into hardboard or 1/4" ply is an exercise in futility, so I just used glue, and used my two 4x4's as long clamps. It would have been a bit easier, if I'd done this before I'd rough-cut the 4x4's, but it worked out.
Anyway, I'd like to know if I'll be able to keep (EDIT: and use) all my tools out there (current and planned) without having the shed become a rust-bucket for the tools and machinery inside. I'll have a 10" contractor's saw out there along with a drill press, a sanding belt, a router & router table, and lots and lots of old tools that I inherited from my Granddad years ago. I live in the Seattle area, so it rains A LOT. But I'm hoping that with the proper ventilation I can keep the tools in the shed dry.
Requirements and electives for the certificate and degree programs in cabinet and fine woodworking include an advanced cabinetry lab and a course in Euro-style hardware. Students in both the construction and cabinet programs can also learn about business contracts, receive training in computer technology and participate in a cooperative work experience.
Why would you buy a costly platform bed from Ikea or somewhere else when you can make one yourself at home? Oh yes, you can. A bed is the most common furniture piece used in the house and probably the costliest one. Wouldn’t it be great if you could just make a bed of your own, without having to spend many bucks for buying one? So I am here sharing a great tutorial to help you to build a nice comfy platform bed that you can use anywhere in the house.
Something like this really does look like it would be a fun project. I guess I need to go out to the yard and use some stakes and brightly colored taped to mark off some different dimensions (12x8, 12x10, 12x12, etc.) to figure out just how big I can make this thing. If I'm building it myself, it'll be easy to keep the height right at the 9 foot limit.
Every piece meets the highest grading standards for Every piece meets the highest grading standards for strength and appearance. This lumber is for a wide range of uses from framing of houses to basic interior finishing applications. Boards can also be used for carpentry hobbies furniture shelving and general finish work. This lumber can also be used in ... More + Product Details Close
The video explains the step by step process of making a nice wooden phone stand from scratch. My first wooden holder was not the best one, but it was good enough to motivate me to make more. I now possess 10 mobile wooden stands in different shapes and styles. And if I can make this, you too can make one yourself. Search the internet for more mobile holder ideas and start making one now.
I had a similar experience with running electrical power to a shed. It turned out that I could build a 12x12 shed without a building permit as long as I did not run utilities, but getting a permit opened a whole new set of requirements that forbid me from having a shed at all. And when the nosey old woman next to me kept calling the building inspector on me, it was suggested that I could run an extension cord out to the shed anytime I wanted as long as it wasn’t fastened in a permanent manner.