Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.


Well, not these plans. You have the option of building a very functional and spacious lean-to shed on different foundations. Your foundation choices are: concrete slab, a wooden floor supported by concrete piers, or a wooden floor supported by skids. That lost option also means that your lean-to could be mobile as well so you won’t have to decide where you want to permanently put it.
Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.
My advice? Don't do this. If you have jointer and a planer, use them. If you don't, seriously consider using dimensional lumber that has already been planed and sanded. If you are going to try to clean up construction lumber by hand, using a hand plane is a lot faster and more pleasant than using a belt sander. Except, of course, that to do a good job of planing a board you need a solid bench to hold the board, and you don't have a bench, yet.

It has been a while since I have posted last, but I do have a question I am pondering. A close family friend has offered to buy me a shed (16 x 12). It looks nice. Double doors, two front windows, vinly siding, and hopefully a ridge vent. Currently I am based in my basement with enough room for my Rigid table saw, bandsaw workbench, some cabinets with very little room for my hand tools, so I used a wall with peg board, and my jointer. My dust collection hangs on the wall as well. (I am being moved outside to free up space in the basement) It is very cramped, but it works. My question is, do wood shops work outside? I know to take precautions of moisture and heat (insulation, dehumidifier, heat for cold season, and so on) but how often to shed workshops work out? Anyone have any ideas on how to keep my tools safe and secondly, does 16 x 12 sound like enough room? Please, I would love some friendly advice.
It has been a while since I have posted last, but I do have a question I am pondering. A close family friend has offered to buy me a shed (16 x 12). It looks nice. Double doors, two front windows, vinly siding, and hopefully a ridge vent. Currently I am based in my basement with enough room for my Rigid table saw, bandsaw workbench, some cabinets with very little room for my hand tools, so I used a wall with peg board, and my jointer. My dust collection hangs on the wall as well. (I am being moved outside to free up space in the basement) It is very cramped, but it works. My question is, do wood shops work outside? I know to take precautions of moisture and heat (insulation, dehumidifier, heat for cold season, and so on) but how often to shed workshops work out? Anyone have any ideas on how to keep my tools safe and secondly, does 16 x 12 sound like enough room? Please, I would love some friendly advice.
After I left the magazine for a new job, I did all of my woodworking in my small two-car garage, but it was a struggle. Power, lighting, and temperature control were limited. And because I shared space with our cars I was always moving machines around, often while in the middle of a project. On top of that, my tool and machine collection had long since eclipsed the space. For all these reasons, fixing up the garage wasn’t an option. My finished basement is a family room, so it was out, too. An addition to the home or a stand-alone building would have been too expensive. I had to find a better path to a shop.
×