@cahudson42 I bored the holes in my sandwich top with a 3/4" power auger bit with the drill in a portable drill guide that kept it vertical and in a way a bit like a plunge router. The guide screw of the auger was dead easy to centre over the laid out grid points. The holes are dead straight and clean sided. The auger bit was new which probably helped. As stated I have three rows from an end vise running the length of the front as well as from the front vise and holes in the front apron to support long pieces as well.
The Handy Home Products Berkley 10 ft. x The Handy Home Products Berkley 10 ft. x 10 ft. Wood Storage Building Kit with Floor is made with factory-primed SmartSide siding to resist fungal decay and wood-destroying insects. The Berkley’s gambrel style roof provides plenty of height to add a loft for extra storage space. The 6 ft. high ... More + Product Details Close
I would say take the shed, you'll find some use for it. I have contemplated this question also. I have a 20' x 11' basement shop, thats quickly loosing space. If you live in an area with a harsh winters (say the midwest), does it make sense to heat the shop through the week if you are only working in the shop on the weekends? Or do you run the heaters just when you are working in the shop? What kind of heaters are recommended (radient, wood stove, etc.)?
In this two day class we will reveal some of the secrets to tuning up a Japanese Hand Plane (Kanna) We will start with conditioning the Body of the Plane (DAI) to stabilize movement. Proper sharpening and grinding of the blade and chip breaker will be discussed and demonstrated. Custom fitting the blade to the Dai and conditioning the sole. We will...
I'm not kidding when I say that this shop has everything you need to make a project happen. They are not only equipped but also some of the nicest people. Supportive and, mostly, willing to help you with your project. The idea is for you to do it on your own, but if you get stuck I have yet to see someone say, "no, figure it out on your own." they are helpful and fair. I love this place, and the people I have met there.
I'd intentionally made it oversize, intending to trim it flush. Trimming is a little more complicated than usual, because I needed to trim it flush on two faces. The end face extended a good 3/8", so I cut off most of the excess with a circular saw and the edge guide, then flipped the edge guide upside down to make a stable platform for the router. Aside from the use of the edge guide, flush trimming the edge face was unremarkable.
Our programs prepare our students to open their own woodworking business or become employed by a high-end woodworking related business. We currently offer an Associate of Science Degree as well as a Certificate of Achievement in 8 different Program Areas. Students may also take coursework to complete a Certificate. Our courses range from Furniture Design and Instrument Making to Production Cabinetmaking. Our graduates are highly employable with the diversity of courses available.
Put the countertop on the base, put the MDF on top of the countertop, and line up the marks you drew on each end of the MDF with the countertop below it. When you have it lined up, clamp things down, and route the edge of the MDF using a 1-1/2" or longer flush-trim bit, with the depth adjusted so the bearing rides on the countertop. I clamped a couple of scraps of doubled MDF at each end to give the router base something extra to ride on at the ends.
By following the Woodworking Course, Woodworking Classes or Start Your Own Woodworking Business Course, you eliminate mistakes most woodworkers make when working on their first project or starting their first woodworking business. Learn the importance of wood selection, joinery and tool purchases. You will understand how to start and make your new woodworking business successful.
Clamp the inner jaw of the end vise in position, leaving a little bit to trim off later, and then use the dowel and dowel center trick through the screw and guiide rod holes of the vise base plate to mark the position of the screw and guide rod holes in the jaw. Remove the jaw and drill 1-1/8" holes in the marked positions. I used the drill guide for most of the holes, and drilled freehand for the last bit. When you're starting a spade bit in a deep hole like this, start the drill very slowly, and the bit will move the drill into a perpendicular position. Start it too fast and the bit will bind and you'll damage the sides of the hole.
2 - use a plunge router with a bottom bearing cuter bit such as this from rockler: http://www.rockler.com/product.cfm?page=25160&site=ROCKLER .... I thought to use the short one as I plunge it directly downward in the centre of the hole until the bearing reaches within the tabletop hole. I suppose one could use a long one, but the stubbiness seemed more practical (the big bearing ensured accuracy?)
One you have the vise jaws shaped so that the vise moves freely, mark and drill holes in the fixed jaw for the bolts that will hold it to the bench. With these drilled, reassemble the vise and mark the location of the holes with an awl. Disassemble the vise and drill the holes through the stretcher, then reassemble the vise and bolt the inner jaw in place.
I thought my first wood working bench was great.A heavy c channel metal frame with a recycled maple floor top with a guick release 7 in vice on the side.It is about 40in by 54in and can hold a hemi no problem. I waxed the top till it was nice and resistant to whatever was dripped on it. Only problem is I was thinking like a gear head not a wood worked.Work piece would slide and no decent clamping on the sides. I figured if I wanted to get somewhat serious about this woodworking thing I needed a real bench not a table with a vice. I read the books and with so many choices I chose a Roubo split top from Benchcrafted it would let me use it for both power and hand tools. I just finished it a week ago and it is nice not to have to chase my work across the bench. I couldn’t find a clear answer for a top coat for the bench I chose to leave the soft maple nude. So I guess I have a bench tbat has a lack of modesty.
Synopsis: No room in the garage? Basement not an option? Consider what Ken St. Onge did when he needed shop space: He bought a prefabricated shed and converted it into his full-time woodshop. Because a pre-built shed doesn’t need a cement foundation and is built in a factory, it’s much less expensive than building an addition or stand-alone shop on your property. It can have taller ceilings than a garage and bigger doors than a basement, both big pluses for a woodworker. You can put a shed just about anywhere, too. Here’s a soup to nuts look at Ken’s experience, so you can gauge whether a shop in a shed is right for you.