With the Grain: A Craftsman’s Guide to Understanding Wood by Christian Becksvoort. A little knowledge about trees goes a long way toward improving your woodworking. You don’t need a degree in dendrology to build a desk. But you do need intimate knowledge of how our raw material grows and – more importantly – how it responds to its environment after it has been cut and dried.
A woodworker's workbench isn't a table, it's a work-holding system. It's not something you set things on top of, it's a tool that holds your work. Where a worktable might have a machinist's vise bolted to its top, a woodworker's bench is built to accommodate a number of different workholding mechanisms, such as bench dogs, planing stops, hold fasts, or board jacks, and will usually have one more woodworker's vises integrated into its structure.
So far, I really like the space. I signed up for a 3 month stint and hopefully will have some things to show for it. For my background, I took shop for 3 years in high school. I've always enjoyed working with wood but never had the space for it. I'm not a master craftsman but there are some really talented people there creating some nice pieces. All levels are welcome here.
The tutorial that I am sharing here was written by someone who built this pallet art just to improve the value of a property they wanted to sell fast and they succeed in it. So you can imagine how wonderful this item must look like. I am assuming you do not just want to make this beautiful pallet art so that you can also sell your property easily. Well, whatever your reasons are, this beauty is able to attract anyone who visits your house.
Next is the shelf. Start with the 24x48" piece of MDF. Clamp this on top of the base, and pencil in the outside of the stretchers and the inside angle of the legs. Flip it over, pull out your trusty cutting guide, and cut it to width and to length. Cutting out the angles is simple, with a jig saw. It's not much work with a hand saw. If you took enough care with supporting blocks and stops, you could probably do it with a circular saw. Since I did have a jig saw, I used it.
Applying the oil is easy. Put on some vinyl gloves, pour some oil in a bowl, take a piece of clean cotton cloth the size of washcloth or smaller, dip it in the oil, and apply it to the wood. You want the wood to be wet., you're not trying to rub it in until it's dry. Apply oil to the entire surface, and then go over it looking for dry spots, applying more oil as needed. After fifteen minutes of keeping it wet, let it sit for another fifteen minutes. Then apply another coat of oil, and let it sit for another fifteen minutes.
Every piece meets the highest grading standards for Every piece meets the highest grading standards for strength and appearance. This lumber is for a wide range of uses from framing of houses to basic interior finishing applications. Boards can also be used for carpentry hobbies furniture shelving and general finish work. This lumber can also be used in ... More + Product Details Close
Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.
If you remember, when drilling the MDF I finished the holes from the other side using a Forstner bit. It made for a clean hole, but the positioning wasn't as precise as I really wanted. So for this, I decided to clamp a length of scrap MDF to the back side, and to drill straight through. My Forstner bits were too short, so I bought an extender. And then I found that the spade bits I was using gave a cleaner exit hole. Whooda thunk?
My first attempt at making a cutting guide didn't work. What I ended up with worked fine for cutting panels, but the guide-strip was too narrow, and when the saw was extended fully for rough-cutting the 4x4's the clamp heads got in the way. So I made another. Actually, I made two more, so that I could cut one into shorter pieces that would be easier to handle.
This rack can be built from old unused wood pallets you can find around the house. So it is also a great way to recycle those old pallets. You can also find a step by step tutorial at instructables.com for which I have included the source link below. This tutorial helps you to make a wood wine rack from the scratch. So what are waiting for? Just grab the items you need and start building a cool wooden rack for those nice wine bottles of yours.
Out of all the shed books I have read, this book stays by my side while I hammer in the yard. The book is well written by what appears to be a non professional book writer (A Good Thing). It reads as if you are getting advise in laymans terms from your neighbor "The Craftsman", a welcome change from the DIY books, that assume a level of expertese. The level of detail is high and discusses gotcha's, advise, and trade "secrets" that could have only come from years of personal experience building sheds.