Here, I am writing about another DIY project that involves the use of an old furniture piece. I think that the idea of reusing and recycling old furniture has got to me. Anyways, I am starting to love it. This project involves using an old door to build a beautiful multi picture frame, as you can see in the image below. This frame looks really wonderful and can be used to hold many pictures at a time.
Still, one of the best features about this woodworking bench has to be its vices. First off, the Sjobergs provides two vices both as sturdily constructed as the bench itself. The same hardware that fastens the bench works to ensure the vices are just as strong. The next main benefit on the vices in the inclusion of multiple positions – four in total – for the vices to go. This allows you to mix and match to suit your needs and allows the table to be used just as easily by right-handed and left-handed users.
I marked the holes by putting a dowel center in the end of a long piece of 1" dowel. Run it through the holes in the base plate, and bang on its end with a mallet. Rotate it a bit and bang it again, and repeat. Odds are the dowel center won't be precisely in the center of the dowel, so you'll be making a small ring of marks. The center of the hole is, of course, the center of that ring.
Having done all this, I'm not sure I'd do it this way again. It might well be faster to layout the positions with compass and straightedge directly onto the top. Either way, you'll want to use a scribe rather than a pencil. Scribe lines are hard to see, and impossible to photograph, but the scribe and compass points click into them, allowing a precision that pencils simply cannot match.
With my second attempt at edge guides, I made the other rough-cut. On this, the edge guide worked fine, but the end of the cuts revealed that the saw blade wasn't quite square. So I adjusted the blade, clamped all four legs together, and made what would be the first final cut, if it came out clean enough. It didn't. I'd let the saw drift a bit away from the guide edge. So I adjusted the saw, moving the guide back half an inch, and tried again. the rough-cut parts were a couple of inches longer than they needed to be, so I had room to work with,. It's only the final cut at the other end that you only have one chance at.
I never, ever, ever bother to write these things. But, I am so incredibly impressed with this product, that I feel compelled to. My six year old daughter LOVES IT, as does my almost four year old daughter. The hammer is just the right size, and it comes with enough pre-cut (good quality) wood for many projects. So far, they have made a house, car, and a plane-- all of which are far more aesthetically pleasing (to me, as a mom) than the plethora of junky plastic toys that seem to fill our home. We've used these projects both as math lessons (measuring the wood, counting the nails needed, learning about angles, reviewing shapes) and during arts & crafts time; but, with just a little creativity, they could be incorporated into just about any learning subject. For the amount of enjoyment we have received, thus far, this product is already worth the money spent, and we have several more projects to go! We will be buying another for little sister's upcoming birthday, most definitely.
Much like the dimensions of a bench’s tabletop, the weight capacity will similarly affect what size of projects you can work on with your bench. A common weight capacity sits between 220 to 250 pounds. While this is okay, it will limit some heavier projects. Ideally, you should shoot for 300 pounds, though some benches can offer 500 pounds of weight capacity or more.
I had a similar experience with running electrical power to a shed. It turned out that I could build a 12x12 shed without a building permit as long as I did not run utilities, but getting a permit opened a whole new set of requirements that forbid me from having a shed at all. And when the nosey old woman next to me kept calling the building inspector on me, it was suggested that I could run an extension cord out to the shed anytime I wanted as long as it wasn’t fastened in a permanent manner.
My wife has given me the OK to buy a "Rancher"-style shed from Lowes and have it installed in the backyard. The discounted installed price will be about $2,600 and this includes the 12' x 8' structure along with a lot of upgrades (twin metal doors, a window, 2 skylights, storage, vents, etc.). I can save about $300 if I build it myself, but my skill level isn't there yet, so I'm going to pay Lowes to assemble it. (See Post #12 below for some photos of the shed and the space I have to work with.)