When you have the other leg seated, the threaded rods will extend father than you want them to. You'll want to mark them so they can be cut to length. Place a washer and a nut on each threaded rod, and then tighten down the nut to pull everything tight. Depending upon the wrench you are using, and how much longer the rod is than it needs to be, you may find it necessary to stack up a number of washers, so that the nut is positioned where the wrench can operate on it.
When the top is done, we want the edged MDF and the oak countertop to have exactly the same dimensions, and for their width to exactly match the width of the base.I could see three ways of doing this: 1, join the MDF to the countertop and use my belt sander to sand down their joined edges to match the base; 2, join the MDF to the countertop and use a hand plane to plane down their joined edges to match the base; or 3, use a flush-trim bit against a straight edge to route the MDF to the width of the base, then join the MDF to the countertop and use the flush-trim bit to route the countertop to match the MDF.

PS:  I saw that a recent review from Nicholas L. hinted that some people weren't welcome at the Community Woodshop. I can say with absolute certainty that everyone I've met has been welcomed with open arms and encouraged to participate at the woodshop. My class is a mix of genders and races, and nobody has experienced any difference in treatment from Bob or anyone else there. I truly can't imagine a situation where anyone would be treated any differently.

I’ve seen antique cabinetmakers’ benches that are sixteen and seventeen feet long, more than three feet wide, and supported by a dozen drawers and doors—and that weigh as much as a felled oak tree. In contrast, jewelers’ cabinets seem to be on a dollhouse scale, with tiny tools to match. For most of us, however, space limitations preclude the biggest, and the smallest are just not big enough.
This class is open to novice woodworkers and to more experienced woodworkers who would like to broaden (or simplify) their approach to woodworking. What do we mean by novice? We think it means you are a person who has decided to commit to learning new skills; to growing a passion for the craft of working with wood; and has a strong sense of the limitations of your own knowledge.
All glue & stain benches are made using a solid maple frame for lasting durability and strength. Side Clamp Benches are made specifically for bar clamps, and are used for gluing projects or clamp storage. Benches feature an open top with 17 sets of 3/4"W grooves that accept bar clamps measuring 3’ and over. Lower center rail is adaptable for storage of hand screws and C-clamps. Side clamp benches are available with or without a drip pan. Glue & Stain Benches are made with a 1-1/4” plywood top covered with heavy-coated galvanized steel. Bottom shelf has a 4” rear retaining lip. Glue and stain benches are available with or without casters. Limited Lifetime Warranty.
Frame making may look simple but it is a skill that escapes many. For a frame to properly do its job it has to be perfect, any mistake can be a distraction that takes away from the artwork it surrounds. This class will focus on skills essential to making square or rectangular frames. Skill building concepts will include how to break down and mill...
I would say take the shed, you'll find some use for it. I have contemplated this question also. I have a 20' x 11' basement shop, thats quickly loosing space. If you live in an area with a harsh winters (say the midwest), does it make sense to heat the shop through the week if you are only working in the shop on the weekends? Or do you run the heaters just when you are working in the shop? What kind of heaters are recommended (radient, wood stove, etc.)?
Cerritos College Woodworking, one of the finest woodworking schools in Southern California, offers classes in furniture making, cabinetmaking, CNC woodworking, and related topics.  Cerritos is the school for you, whether your goal is to acquire new knowledge, gain confidence in or improve your skills, enter the field of professional woodworking, or develop a rewarding hobby.
If you opt for a bench with drawers or cabinets built into its base, don’t forget the toe spaces: Leave a space roughly three inches deep and four inches wide at floor level for your toes, just like kitchen cabinets. The absence of a toe space means you’ll be forever kicking the face or sides of the cabinets which is irksome and, with tools in hand, potentially dangerous. And you’ll have to lean over farther to reach the back of the benchtop.
You can also make one for elders and put it in your garden or terrace or anywhere in the house. Elders can use it to relax and kids can use it to play or sleep. Although this is a really beautiful piece of woodwork, it is not that easy to make. Only someone with good woodworking skill can think of making this swing set. Also, I couldn’t find a good tutorial that illustrates the process of building a wooden boat-shaped swing set. Most Probably, I will write one when I build mine.But if you really want this swing set like right now, I would suggest you hire a good woodworker, who can build something similar. Or just search the internet and maybe you get lucky enough to find a tutorial for this. Good luck either way.
I decided to finish the top with a number of coats of Danish oil, followed by a coat of wax. I applied the first coat of oil in the usual manner, making sure to cover the edges, and down the holes. I applied a coat oil to the top side of the shelf, as well. Wipe it on, let it sit wet for half-an-hour, then rub it off. Wait a day or two, add a second coat, and then again for a third.
Our stationary equipment runs the complete range from heavy-duty industrial machines, to inexpensive home shop type of tooling so that each student can compare and contrast the range and versatility of equipment at a wide variety of price points.  We spend time on what makes a good machine good, an adequate one adequate, and a lousy machine worthless. We have no commercial sponsors and will share our opinions based on our experiences regarding the quality of one manufacturer over another.  There is no better place to kick the tires on a variety of equipment than at our shop.     
The holes we want to mark are the holes through which the threaded rod connecting the two legs will run. This threaded rod will run through the 3/8" groove along the bottom of the short stretchers,. The hole for the upper stretcher has to be positioned so that when the rod is running through this groove, the top of the short stretcher is even with the top of the legs. The most precise way I've found for marking the position of this hole is to use a dowel center. Fit the dowel center into the bottom groove, line up the stretcher, and bang on the end with a rubber mallet. The dowel center will leave a mark indicating the center of the hole.
Rocking horses, toy chests and dollhouses are just a few of the classic gifts generations have treasured. Now you can give all the pint-sized DIYers on your list those same classic gifts, and make them yourself with the help of these DIY toy kits. They're perfect for kids of all ages, and will be treasured for years to come. The best part? All these gifts can still make it to your door by Christmas.
The front edge of a woodworker’s bench is usually lined with square holes positioned at regular intervals. These holes hold bench dogs and holdfast clamps in place for securing work pieces. Beneath the top of the bench, some cabinetmaker models feature single storage drawers, others several drawers and even cupboards incorporated into a case-like base.
Practical Woodworking is a 50 hour comprehensive course that focuses on the necessary skills, tools, techniques, and safety to successfully enter the world of woodworking and furniture making. Beginner, intermediate, and advanced students learn about furniture design, construction, and finishing as well as wood behavior, hand tools, machines, milling from the rough, squaring, and joinery. It  is an intensive class for folks who want to continue woodworking in the future. It is a week of hard work with a lot of fun mixed in. Watch the video and read below for a more in-depth look at what we're all about.
If you don't quite have the space for a real pony, make this handcrafted wood version instead. The horse pictured here is unfinished pine, but there are lots of woods and finishes to choose from. Everything you need comes with the kit, and the plans can be downloaded. If you don't want to build it yourself, you can order from the website—just allow two to three weeks to ship.
At the age of 9, Mark’s interest in woodworking began, which led him to begin an apprenticeship with Homestead Heritage Furniture at the age of 17. In his own shop he has built many pieces of furniture from small dovetail boxes to large 10′ round conference tables. Most of his work has been for clients who have ordered custom pieces for their homes and offices. Mark has been building custom furniture for the last 20 years and is now the manager of the Heritage Furniture business. Mark enjoys making hand tools and jigs that can simplify the building process. He has taught children how to shape simple utensils like wooden spoons and cutting boards as well as other larger projects. “Seeing the young grow to maturity in their craft is what I appreciate.”
My first shop was a 8 x 10 ft room, actually a bedroom, with 10 ft high ceilings in a older home in Chicago. I had a 10" Craftsman TS, drill press, 8 1/4" Skil saw which still works, some welding tanks, hand tools and... my bed was a loft across the 10 ft length 4 ft down from the ceiling with a ladder against the wall to get up. I was 16 yrs old then, now I am 66 yrs, have 2 shops with Craftsman power tools up stairs, and Grizzly tools ,a Powermatic 68, a MIG welder, and other tools on the ground floor. I've come a long way, You think? I remember making bases for sculptures called "plinths", my first commission, in the living room, 5 pieces rather large, several ft long and wide. The house was haunted, and my mom told the "spirit" to leave and go back downstairs. There was a cold draft and the straw chair would rustle with no one sitting in it. Wow, does that bring back memories from the '60's.
When you're working with linseed oil, never -- I mean NEVER -- leave used rags lying around. Hang them up outside, away from anything combustible, and where there's enough air circulation to keep them cool. Or put them in a bucket of water, and hang them outside later. If you're just setting a rag down for the moment, set it out flat, without folds, on something non-flammable. Hanging outside in the breeze, the oil in the rags won't retain heat while they oxidize. For the oil to completely oxidize can take in a couple of days, if it's warm, or more than a week, if it's cold and rainy. When fully oxidized, the oil will be solid and the rags will be stiff. At that point, they're safe, and can be thrown in the trash. Toss them in the trash before that, and you might as well say goodbye to your garage.

The bench would end up being about 5 feet long. I thought about cutting 5 feet out of my 8 feet long countertop and use the rest for a small support table. However, after a consideration, I decided to bypass the front vise altogether together with the overhang so my bench will be 4 feet long. This allows me to skip the MDF and just glue the two halves of the 8 feet board together.
To mark the centerline, set a compass to span something more than half the width of the leg. Draw an arc from corner of the leg. The point where the arcs intersect will be on the centerline. With a centerline point on each end of the leg, place a scribe on the point, slide a straightedge up to touch the scribe. Do the same on the other end. When you have the straightedge positioned so that you can touch both points with the scribe, and in each case it is touching the straightedge - without moving the straightedge - scribe the line. Use scribes, rather than pencils or pens, because they make more precise marks.
Much like the dimensions of a bench’s tabletop, the weight capacity will similarly affect what size of projects you can work on with your bench. A common weight capacity sits between 220 to 250 pounds. While this is okay, it will limit some heavier projects. Ideally, you should shoot for 300 pounds, though some benches can offer 500 pounds of weight capacity or more.
Those bums even have a stipulation that you can't connect any utilities to a shed. My plan is to adhere to the letter of the law if not the spirit. I plan to run a buried 20 amp power line out to the shed (this will be done professionally and properly according to whatever is required by the law), but it will require a manual connection to a junction box on the outside of my house to complete the circuit. That way, I can argue that the electrical connection is only temporary and is little more than a safe and buried version of an extension cord.
×