Working with wood fresh from the log, this green woodworking project is the perfect introduction to edge tools and wood grain.  In the first week you will produce a three-legged stool using buck and “whip”saws for crosscutting the log to length; wedges and froes for splitting out leg stock; drawknife and spokeshaves at a shaving horse for shaping the legs; and using travishers, rounding planes and specialized rasps for shaping the seat.
With the inner jaw fastened to the bench, I used the router to flush-trim the jaw to the benchtop, across the top and down the sides adjacent to the top (stopping short of the discontinuity between the top and the legs). I'd thought this would be the best way to match up the jaw against the top, but I'd not do it this way again. It was very difficult to hold the router tight against the face of the jaw, and the result was a surface that wasn't as even as I had hoped.
Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.
Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.
Applying the oil is easy. Put on some vinyl gloves, pour some oil in a bowl, take a piece of clean cotton cloth the size of washcloth or smaller, dip it in the oil, and apply it to the wood. You want the wood to be wet., you're not trying to rub it in until it's dry. Apply oil to the entire surface, and then go over it looking for dry spots, applying more oil as needed. After fifteen minutes of keeping it wet, let it sit for another fifteen minutes. Then apply another coat of oil, and let it sit for another fifteen minutes.
A woodworker's Workbench is a special type of bench designed to hold your work when you are working on a wood project. The main purpose of this table is to keep the woodwork steady and to prevent it from moving. Follow the tutorial below to build yourself a nice workbench suitable for your specific woodworking projects. Make sure to modify the table to fit your specific requirements.
Working with wood fresh from the log, this green woodworking project is the perfect introduction to edge tools and wood grain.  In the first week you will produce a three-legged stool using buck and “whip”saws for crosscutting the log to length; wedges and froes for splitting out leg stock; drawknife and spokeshaves at a shaving horse for shaping the legs; and using travishers, rounding planes and specialized rasps for shaping the seat.

Every piece meets the highest grading standards for Every piece meets the highest grading standards for strength and appearance. This lumber is for a wide range of uses from framing of houses to basic interior finishing applications. Boards can also be used for carpentry hobbies furniture shelving and general finish work. This lumber can also be used in ...  More + Product Details Close


Not sure about Midwest but I have a 24 x 14 Game rm attached to my shop and I put a small window unit/heat pump in the wall. It stays comfortable all year round. It get really hot here and we had a several day in the 20's this winter but it's insulated well. That might not be as cold or as hot as in some places but the unit I haze does not run that often and has a low cost rating. I'm planning on putting a larger unit in the shop area even though I do like to work with the garage door open. The door is insulated so I can run A/c in there. Just my .02.

For the router you'll need a a 3/8" straight bit, an edge guide, 1/4"- and 1/8"-radius roundover bits, and a flush-trim bit with at least a 1-1/2" cutting length. Bits of this size are available only for a 1/2" collet. Some routers are capable of using multiple collet sizes. I was fool enough to buy a router that only had a 1/4" collet. More on that, later.


This is definitely going to be one of the easiest woodworking projects you’ll be reading about today. So why not just get started? The tutorial link is given below. Just do exactly what they are saying in the tutorial and you will end up making a beautiful wooden doormat just like the one in the image above. They are using pine wood to build this doormat. You can choose any wood material that best suits your budget.

While a strict figure for the bench’s weight capacity is not available, a quick browse through their other stand and bench products shows a general weight capacity well above most other brands. As such, while we cannot say for certain that this bench provides the best weight capacity, it is more than likely that it the capacity is similar to the other products in the catalog.
I live in the second rainiest city in the country, Pensacola, so I am used to dealing with wet. I literally work out of my garage (read storage area, small woodwork area, washer/dryer...car? ). I wheel bigger tools and table out to the little covered area in front of the garage. I have an 8 x 10 aluminum shed that is strictly garden stuff storage. I mention this for two reasons.

We are especially proud of Post Woodworking’s Brunswick style shed. It has all the rugged features and simple, beautiful mystique of a Maine coastline. Natural-wood siding options, in pine or cedar, offer a rustic aesthetic. Or, choose a vinyl color that complements our home. Once inside the Brunswick, its unique, two-sided sloped roof maximizes headroom, making space for you to better maneuver a rake. Black architectural hinges and hardware lend distinguished contrast and quality to this basic but appealing storage solution.
×