2. Did I mention the rain here? How is your shed built? Are flooring and walls sealed to prevent water blowing and leaking in? When we get our summer thunderstorms the winds can whip up the rain pretty good and I even have to make sure garage door is closed sometimes. The shed??? Yea. it gets wet inside no matter how much caulk I use on floor gaps. Mine is on slab and shed not really designed to be waterproof. That being said, even if I got floor sealed it still lets some water in where walls meet roof. Not lots but makes for extreme humidity (or dew point if you prefer) levels.
The edges of MDF are fragile, easily crushed or torn. MDF is also notorious for absorbing water through these edges, causing the panels to swell. In Sam Allen's original design, he edged the MDF with 1/4" hardboard. This edging is one of the complexities that Asa Christiana left out in his simplified design. I think this was a mistake. MDF really needs some sort of protection, especially on the edges.
Yea I had a friend who went the HD route and in after putting new braces up for the roof and an extra layer of plywood on the floor he gave up the fight and tore it down. We ended up building twice the shed that was 100 times more sturdy for less than he had invested in the first one. I would go any route that is the opposite way of HD or Lowes. Learn from this guy.
Stan Beckworth began his woodworking career in 1983. His wide experience in woodworking enables him to teach as a practicing master craftsman. He began woodworking because of a desire to work with his hands and pass some hand skills to his children. Some of the classes he teaches are the Finishing class, Relief Carving class, Foundational Classes and the Advanced Furniture courses, such as the Chest of Drawers and Rocking Chair classes. Stan has spent a lot of time learning about furniture finishes, as well as relief carving, studying with Mary May, a renowned woodcarver in South Carolina. When Stan isn’t teaching, he runs a small remodeling business at his home and builds and refinishes furniture for different clients. He has been commissioned to make furniture for several congressmen as well as refinishing furniture for past presidents. ”Being able to pass on practical skills that are useful for everyday application is what I love to do.”
In this two day class we will reveal some of the secrets to tuning up a Japanese Hand Plane (Kanna) We will start with conditioning the Body of the Plane (DAI) to stabilize movement. Proper sharpening and grinding of the blade and chip breaker will be discussed and demonstrated. Custom fitting the blade to the Dai and conditioning the sole. We will...
The video explains the step by step process of making a nice wooden phone stand from scratch. My first wooden holder was not the best one, but it was good enough to motivate me to make more. I now possess 10 mobile wooden stands in different shapes and styles. And if I can make this, you too can make one yourself. Search the internet for more mobile holder ideas and start making one now.

A bottle carrier is a bucket like carrier used to carry beer bottles and so. Yes, the same one you must have used to carry your six-pack. Drinker or not, a bottle carrier is a useful item for everyone. It can be used to carry around or store small items around a household. And it is also very easy to build one. I have several of these lying around my house. Also known as wooden beer totes, this is one wood item you will absolutely love to make. It is also super easy to build.
Be careful. Single 24x60" sheets of 3/4" MDF are pretty easy to lift. A doubled sheet is manageable. The countertop - 24x72" panel of 1-1/2" oak - weighs something over 100 pounds. It takes real care to lift safely. The joined top - 3" thick of oak and MDF - is past the range that can be lifted safely by one person. Don't try. Get a friend to help, or rig a block-and-tackle.

This is one of those things that you never know you need unless you have one. This amazing wooden sofa sleeve works perfectly on either or both sides of a sofa set. It gives your sofa a nice look. The sleeve can also be modified to include a cup holder, mobile holder, etc. You can easily find this item on any online furniture store, but an even better idea is to build one. This way, you can make a sofa sleeve design that you actually like and make space for cup and other things.
Our stationary equipment runs the complete range from heavy-duty industrial machines, to inexpensive home shop type of tooling so that each student can compare and contrast the range and versatility of equipment at a wide variety of price points.  We spend time on what makes a good machine good, an adequate one adequate, and a lousy machine worthless. We have no commercial sponsors and will share our opinions based on our experiences regarding the quality of one manufacturer over another.  There is no better place to kick the tires on a variety of equipment than at our shop.     
The source above is not exactly a tutorial, but it gives you a basic idea of how the author built a Quirky Pallet Art to enhance the look of their old house. You can also find another tutorial at the link below. It shares a step by step procedure for making a wooden pallet sign. The final product is not exactly the same as the one above, but the basic idea is the same.
2. Did I mention the rain here? How is your shed built? Are flooring and walls sealed to prevent water blowing and leaking in? When we get our summer thunderstorms the winds can whip up the rain pretty good and I even have to make sure garage door is closed sometimes. The shed??? Yea. it gets wet inside no matter how much caulk I use on floor gaps. Mine is on slab and shed not really designed to be waterproof. That being said, even if I got floor sealed it still lets some water in where walls meet roof. Not lots but makes for extreme humidity (or dew point if you prefer) levels.
I love the opportunity Community Woodshop provides to take advantage of the tools, high-end equipment and hands on skills they'll assist you with when working with woods and metals. I'm not too sure about the Community part because I'd probably not come back because of the distance, however I do recommend learning to build shit on your own rather than paying a hefty price for the same materials that all furniture and fixtures and most jewelry are made of. They offer a wide variety of classes that teach you skills to build different items and use different tools.
The original design had a height of 35-1/8". Their two-layer top was 1-1/2" thick, so their legs were 33-5/8" long. I want a height of 35", but I'm using a top that's 3" thick. My basement floor is anything but level, so I'm using levelers that are adjustable from 3/4" to 1-1/2". In other words, I want legs that are around 31-3/4" long. (If you're not using levelers, your legs need precise lengths. The levelers give about 3/4" of adjustment, so precision is less necessary.
For the router you'll need a a 3/8" straight bit, an edge guide, 1/4"- and 1/8"-radius roundover bits, and a flush-trim bit with at least a 1-1/2" cutting length. Bits of this size are available only for a 1/2" collet. Some routers are capable of using multiple collet sizes. I was fool enough to buy a router that only had a 1/4" collet. More on that, later.

It is one of the easiest woodwork projects we are going to discuss today. Although it looks very easy to make, I still could not find any good tutorial on the internet that explains how to build this one. So I am here sharing an article link that gets the closest. The article explains how to make different kinds of DIY candle holders and what items you may need for the project.

I made a template by scribing two adjoining squares on a piece of MDF, using compass and straightedge, then marking each corner with a centerpunch, then drilling the points with a 1/16" bit. I find I'm always breaking small bits, so I picked up a couple of each size some months ago, and on looking I found I had three 1/16" bits, which worked fine for what I intended.


Through demonstrations and practice you will learn how to build a Simple Table Top. Square wood using the Jointer, Planer and Table Saw, then learn how to use the Festool Domino Joiner to keep perfect registration during the glue up. This will be a group project where everyone will help build a single table top. The goal is to gain experience and confidence...

For one, the bench itself is a good size. While its width as a tad short at just over 1 ½’, the length is a great 5’ long. Even better, this bench is made out of birch wood. Birchwood is similar to beech in that it is strong but soft enough to prevent inadvertent dulling of your tools. However, birch has a bit of an advantage over beech in that it is not a porous which makes staining on the Windsor Design a more worry-free affair.
I agree that even at 12x12, things'll be "cozy" inside. That's OK. Keep in mind that this will be a general purpose hobby shed, not just a wood working shed. Even 12x8 would be plenty big enough for building 1 meter wingspan bungee launched RC gliders. And for the electronics projects I do, I only need enough workbench space to do some soldering with a 3rd hand (for electric guitar pedals). If I need more room than the shed offers for wood working projects, I'll just roll the table saw down a ramp and do my cutting outside in the sun.
Grizzly is a company currently undergoing an upheaval. This brand was once known as a manufacturer of professional grade tools and equipment for woodworking products. Though, in recent years, that reputation has begun to slip a bit since being bought by the Chinese company SIEG. These days, whether the Grizzly product stands up to its previous standards of excellence often has more to do with what you are buying than the company itself.

In general, students in the certificate and degree programs learn how to understand and create their own shop drawings and design custom cabinetry. In the process, they also find out how to use the same tools and machines employed in the woodworking business and assemble cabinets according to industry standards. Additional program topics include the use of contemporary hardware in design.
Working with wood fresh from the log, this green woodworking project is the perfect introduction to edge tools and wood grain.  In the first week you will produce a three-legged stool using buck and “whip”saws for crosscutting the log to length; wedges and froes for splitting out leg stock; drawknife and spokeshaves at a shaving horse for shaping the legs; and using travishers, rounding planes and specialized rasps for shaping the seat.
Who doesn’t want to have one awesome and handy wooden desk organizer that not only looks beautiful but can store all your mini office desk items properly? See the picture below. I am sure you will love this one. I have already built one myself as I just could not resist having one at my office. This thing easily stores all my office desk essentials, including pen, pencils, marker, small notebooks, etc. in the most organized way. You can see it yourself.
Windsor Design is an interesting brand in that it is not actually its own company. Instead, Windsor Design is one of the in-house brands sold by Harbor Freight. While it may be a store brand, that should not dissuade you at all as Harbor Freight is known for selling some of the best products available for all fields of construction. Granted, this may not strictly be the best table available, but it does provide a solid mix of features to make it a good value.
I marked the holes by putting a dowel center in the end of a long piece of 1" dowel. Run it through the holes in the base plate, and bang on its end with a mallet. Rotate it a bit and bang it again, and repeat. Odds are the dowel center won't be precisely in the center of the dowel, so you'll be making a small ring of marks. The center of the hole is, of course, the center of that ring.
Whether you're just starting out or wish to upgrade your important hand tools, this 5-Pc. Professional Woodworking Kit with matching rosewood and brass accents has all the essentials for producing the very best work. This fine set includes a 9" smoothing plane, 6" block plane, 9" try square, 9" marking gauge, 9" bevel gauge and a fitted wooden case.

Woodworking Workbenches are available in a variety of styles. Open Style Wood Workbenches feature a large work surface and a lower shelf. 2-1/4" thick maple top with maple plywood lower shelf. Open Style Wood Workbenches are available as a 2-station unit (28"W) or a 4-station unit (54"W). Open Style Auxiliary Workbenches are used for placement against walls. Shelf features a rear curb to keep contents in place. Solid maple top features angle iron front edge. Plywood shelf is open for maximum functionality. Solid maple legs. Environmentally-friendly UV finish. Units measure 24"D and are available in several lengths and heights. Mitre Box Benches ensure wood pieces are kept flat while mitres are cut. Bench is made using solid maple unit with environmentally-friendly UV finish. Holds a mitre saw up to 26"W and provides a 24" square work surface on both sides. Mitre Box Benches measure 33-3/4"H. Sheet Metal Workbenches are made with a 2-1/4" thick maple top and is protected on two long edges with 2" x 2" angle iron. Solid maple legs and stringers. Plywood shelves are designed to provide open storage of 30" metal sheets. Measures 40"D x 32"H and available in widths of 60" or 96".
This particular tray is made using reclaimed barn wood but the author of the project Beyond The Picket Fence surprised everyone with one fact: reclaimed barn wood has often some areas turned pink due to cow urine. If you check the project more closely, you’ll also notice some areas of the tray being almost bright pink. That’s something you don’t see every day!
I live in the second rainiest city in the country, Pensacola, so I am used to dealing with wet. I literally work out of my garage (read storage area, small woodwork area, washer/dryer...car? ). I wheel bigger tools and table out to the little covered area in front of the garage. I have an 8 x 10 aluminum shed that is strictly garden stuff storage. I mention this for two reasons.
×