Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.


During an intensive six-month course, not only will you learn all of the basics such as the different tools you will be using but also get a chance to try some of our more advanced projects. These will include how to draw up a big project such as a workbench, and French Polish your own jewellery box. You will also learn how to draw and can take part in our design courses, an invaluable part of the making process.
I agree that even at 12x12, things'll be "cozy" inside. That's OK. Keep in mind that this will be a general purpose hobby shed, not just a wood working shed. Even 12x8 would be plenty big enough for building 1 meter wingspan bungee launched RC gliders. And for the electronics projects I do, I only need enough workbench space to do some soldering with a 3rd hand (for electric guitar pedals). If I need more room than the shed offers for wood working projects, I'll just roll the table saw down a ramp and do my cutting outside in the sun.
I drilled from the mark. That way I could ensure that the hole was where it was supposed to be, on the side where the position was critical. I have two 3/8" bits -- a brad point bit that came with my doweling set, and a perfectly ordinary 3/8" twist bit. Brad-point bits are far more precise than twist bits -- they're more likely to start where you want them to, and they're more likely to stay straight. My problem is that my brad-point bit wasn't long enough to go through 3-1/2" of wood. So I started each hole with the brad-point bit, then finished it off with the twist bit. I clamped a piece of ply on the back, to reduce tear-out.

You don’t need a fully equipped shop to enjoy woodworking! In this class, you will learn to design, make, and finish a unique wood box. With an emphasis on tool safety and material exploration, we will use a combination of power tools and hand tools to make boxes of all shapes and sizes. Beginning with a solid block of wood, you will learn how to lay out, cut, sculpt, and reassemble the block into the form of a box. Demonstrated techniques will include hidden hinges, small drawers, pull knobs, and fitted lids, as well as texturing, carving, burning, painting, and finishing. Suitable for beginning and intermediate students, all materials provided.

Whether you’re setting up a new shop or upgrading your old one, a good, sturdy workbench will almost surely be central to your plans. We can help. Our editors and contributors have produced more than two dozen articles and videos about benches and assembly tables. We’ve included everything from a simple but workable plywood bench to a classic hardwood bench complete with vises. You’ll also find full project plans, as well as tips for installing vises, making your bench portable, adding storage, and more. Some of our workbench plans are free, and the rest can be purchased in our store (check the links below).

After you have all the holes clean, set things up for your glue-up. You want everything on-hand before you start - drill, driver bit, glue, roller or whatever you're going to spread the glue with, and four clamps for the corners. You'll need a flat surface to do the glue-up on - I used my hollow core door on top my bench base - and another somewhat-flat surface to put the other panel on. My folding table was still holding my oak countertop, which makes a great flat surface, but I want to make sure I didn't drip glue on it so I covered it with some painters plastic that was left over from the last bedroom we painted.
When the top is done, we want the edged MDF and the oak countertop to have exactly the same dimensions, and for their width to exactly match the width of the base.I could see three ways of doing this: 1, join the MDF to the countertop and use my belt sander to sand down their joined edges to match the base; 2, join the MDF to the countertop and use a hand plane to plane down their joined edges to match the base; or 3, use a flush-trim bit against a straight edge to route the MDF to the width of the base, then join the MDF to the countertop and use the flush-trim bit to route the countertop to match the MDF.

I would say take the shed, you'll find some use for it. I have contemplated this question also. I have a 20' x 11' basement shop, thats quickly loosing space. If you live in an area with a harsh winters (say the midwest), does it make sense to heat the shop through the week if you are only working in the shop on the weekends? Or do you run the heaters just when you are working in the shop? What kind of heaters are recommended (radient, wood stove, etc.)?


With the inner jaw fastened to the bench, I used the router to flush-trim the jaw to the benchtop, across the top and down the sides adjacent to the top (stopping short of the discontinuity between the top and the legs). I'd thought this would be the best way to match up the jaw against the top, but I'd not do it this way again. It was very difficult to hold the router tight against the face of the jaw, and the result was a surface that wasn't as even as I had hoped.
Constructed with the classic craftsmanship that Grey’s Woodworks is known for, our beautiful sheds come in a variety of styles, sizes and colors. We will help you design a shed to match your surroundings and meet your needs. Select from our pine tongue and groove, duratemp T1-11, or vinyl sidings and arrange doors and windows to your liking. All of our sheds are handcrafted in modern workshops. Not only does a shed from Grey’s Woodworks provide much needed storage space for your mower, snow blower or bike, but it also makes for an attractive addition to your property.
The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details. Follow the steps properly to make a nice and strong wall rack. This rack makes use of magnets to hold metal items. The tutorial explains the procedure for building this beautiful wall rack. Make sure to use only high quality items for any woodworking project. Use the rack only to hang items that are not too heavy for the magnet to hold. Also, be careful while working around this wall rack and beware of the knives falling off the rack.
Our Lexington model was designed to match many traditional New England homes, in Massachusetts and beyond. The steep pitch of the roof is built to withstand sometimes-punishing New England snow loads and complement today’s home design styles. Post Woodworking can match most vinyl siding colors, so that your shed color will coordinate with your home as well. And as is the case with all of our sheds, interior solar lighting is available to light up the night.
×