Can't say enough about the team at Post Woodworking, Inc., from Karen in the office to the team that... put up this beauty starting at 7AM and were done before lunch, Kyle, Aaron and Billy. After what sounded like a late night at the shop the night prior, they were still on site bright and early as promised and still energized and ready to show their pride in their work. Couldn't be more happy with our 14' x 20' Cohasset. See More
It doesn't get much better than a day at the woodshop! I've taken several classes from cutting boards to turning vases. It is always fun and informative! All of the machines are top notch and the instructors are great! I've toyed with the idea of a membership but I think I'll take a couple more classes before doing so! I can't wait to see the new location! :)
Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.
My advice? Don't do this. If you have jointer and a planer, use them. If you don't, seriously consider using dimensional lumber that has already been planed and sanded. If you are going to try to clean up construction lumber by hand, using a hand plane is a lot faster and more pleasant than using a belt sander. Except, of course, that to do a good job of planing a board you need a solid bench to hold the board, and you don't have a bench, yet.

Workbenches have flat tops, though sometimes at the rear there is a cavity called a tool well that contains tools and components (and prevents them from falling off). One advantage of having the well set into the top of the bench is that, even with a variety of objects in the well, a large sheet of material can still be laid flat over the entire surface of the bench; the contents of the tool well offer no interference.
A woodworker's Workbench is a special type of bench designed to hold your work when you are working on a wood project. The main purpose of this table is to keep the woodwork steady and to prevent it from moving. Follow the tutorial below to build yourself a nice workbench suitable for your specific woodworking projects. Make sure to modify the table to fit your specific requirements.
So far, I really like the space. I signed up for a 3 month stint and hopefully will have some things to show for it. For my background, I took shop for 3 years in high school. I've always enjoyed working with wood but never had the space for it. I'm not a master craftsman but there are some really talented people there creating some nice pieces. All levels are welcome here.
A couple nice qualities about this bench include the weight and vice capacities. The weight capacity of this bench is 330 pounds which is decent, though it will not wow you too much. The vice, on the other hand, provides a 7” capacity which is tied for the most on our list. That said, there is only a single vice, and it is not able to be repositioned. This can make things a bit frustrating for lefties as it is a right-handed configuration.
If you're using drywall screws, you'll want to countersink the holes. Drywall screws are flat-head, and need a countersink to seat solidly. If you're using Kreg pocket screws, the way I did, you won't want to counter-sink the holes. Kreg screws are pan-head, and seat just fine against a flat surface. Both drywall screws and Kreg pocket screws are self-threading, so you don't need pilot holes in the second sheet of MDF.
Sjobergs’ woodworking benches are recognized all over the world for their durability, handy design and extra features that make these benches well worth the money. This Hobby Plus bench is the perfect fit for a woodworking enthusiast, especially since it is equipped with two vices and bench dogs. This could become your one and only woodworking station!

As simple as its elements are, the workbench is more than a tabletop with legs, a well, and a few holes. Virtually everything in the workshop comes to rest on the bench at some point, even if only between operations at other stations. Planning and layout, cutting and shaping, assembling and finishing–all can be, and often are, performed on the benchtop. The better the design, and the better suited its size and configuration to your labors, the more efficient a tool it will be.


Chris I blame you for all these altars that are being built today and now you thinks we over thinks ’em–huh. You whipped the masses into a frenzy— now Woodworkers are trying to out pretty each other–out wood species each other –out Rube Goldberg each other. I made 2 benches in 30 years neither had a through dovetail but many were made on them and I have no idea but I would bet a dollar that neither weighed 280 pounds but they both had tons of wood on them. If you want the bench as a destination god bless but it was intended as a mean. Thats my rant I could be wrong

Happy bench building folks. I hope you make it your own and not worry too much about what someone else thinks it should be. Use the rules as a guideline, they have validity, but make it your own in the end. If the rules fit you that’s great, if they don’t quite fit you then make it to fit yourself. It’s you using it, not some guy making a nice living off of telling you how he thinks you should do it. One size does not fit all. Never has, never will.
Have you got an old whiskey barrel at home that you haven’t used for ages? If yes, this project is for you. You can make a really beautiful coffee table from that old whiskey barrel in a few easy steps. Apart from a coffee table, whiskey barrels can also be used to build several other furniture items. But that is a talk for later. Here, we will discuss how to make a coffee table from a whiskey barrel.
I recently came across this beautiful wooden swing set, which was made in the shape of a boat. Cool, isn’t it? The very first look was enough for me to start loving it. Although I haven’t yet tried building one myself, I am definitely going to. Later I realized that you can also build a baby cradle with the same idea. After all, what can be more calming than the tender rocking of a boat? This swing set will surely help your child get more gentle sleep.
Mine is similar but a bit more robust. The top is a sandwich, two 18mm sheets of WBP ply with an 18mm mdf filling. The legs are mortise and tenoned together, the ends glued and pegged, the stretchers are joined with long bolts so it comes apart. I stiffened it by adding a very closely fitted cabinet underneath (it had to go in dead square) and it is now absolutely rock solid.
Requirements and electives for the certificate and degree programs in cabinet and fine woodworking include an advanced cabinetry lab and a course in Euro-style hardware. Students in both the construction and cabinet programs can also learn about business contracts, receive training in computer technology and participate in a cooperative work experience.

I live in VA and my workshop is an unheated, uninsulated garage. I work out there year round, even when temps are below freezing. I can't say it's comfortable in the winter (or when it's 100 degrees with 95% humidity) but I haven't had any major issues. I have had some big box green wood warp on me after I built a couple bookshelves and brought them into the house, but that was more a factor of the green wood than my "shop".
The Cape Ann Shed was designed with coastal New England in mind. So yard work may feel like you’re actually on vacation. From Cape Cod to the beaches of Maine, you will find a Post Woodworking Cape Ann shed adorning the yards of thousands of homes. It’s a popular style with our customers – whether they make their home by street or by sea. An affordable choice for an outdoor structure, the Cape Ann brings functional elements with nautical appeal.
×