The Practical Woodworking course at the JD Lohr School of Woodworking is a complete and comprehensive woodworking course held in our shop on the 13-acre farm in southeastern PA. This is total immersion woodworking for ambitious, interested adults. With class size limited to 11 students and 3-4 instructors in each class, all needs of every student are met regardless of experience level. If you are self taught with no formal training as a woodworker, this course will quite literally change the way you work.
Practical Woodworking is a 50 hour comprehensive course that focuses on the necessary skills, tools, techniques, and safety to successfully enter the world of woodworking and furniture making. Beginner, intermediate, and advanced students learn about furniture design, construction, and finishing as well as wood behavior, hand tools, machines, milling from the rough, squaring, and joinery. It  is an intensive class for folks who want to continue woodworking in the future. It is a week of hard work with a lot of fun mixed in. Watch the video and read below for a more in-depth look at what we're all about.
First, we need to drill out the holes for the screws that will hold them together. While the two layers of MDF are glued, the countertop and the MDF will only be screwed. The oak countertop, like any natural wood product, will expand and contract with humidity changes. If it were glued to the MDF, the difference in expansion of the two layers would cause the countertop to buckle and curl.

Flip the base upright, put the MDF on top of it, then use a straightedge to draw two straight lines joining the outside edges of the legs and extending the width of the MDF. I used the countertop as the straightedge. We cut it with our cutting guide, which is based on the factory edge of a sheet of 1/4" plywood, so it should be straight enough. Use a carpenter's square to transfer these lines onto the ends of the MDF.
While $115 may seem expensive, try accurately boring a grid of 20mm holes on 96mm centers in 3/4 MDF. I have for a table for our retirement community shop - - its a pita. Plus the MFT material seems denser and more water resistant than garden-variety MDF. And the single-thickness has proven sufficient the last several years on my original 1080s. Still dead flat.
Students will make two pens at the lathe, one of solid wood and one of your own design built up from several pieces of wood. Since turning pens is a quick process, we will have time to teach you how to choose woods, how to prepare and mount wood on the lathe, and several of the more popular finishes. We will cover safe operation of a lathe, demonstrate how to use common woodworking tools, practice tool sharpening techniques, and discuss options for what kind of lathe you might want in the future, from a small pen lathe to more robust machines that can handle much bigger projects. Bring clothes that can get dirty.
You can transfer a graphic on any wood piece of your choice, including a frame, top of a table, etc. The surface should be clean and big enough for the graphic paper. I am also sharing a video tutorial here that explains in detail the process of transferring any graphic to a wooden surface using a freezer paper. Just gather the items you need and follow this video to carve your favorite designs on your favorite wood items.
So drill the benchdog holes through the MDF layer. Begin by laying out their positions. You'll want these to be precise, so that the distances between the holes are consistent. The vises you are using will constrain your benchdog spacing. My front vise worked most naturally with two rows of holes four inches apart, my end vise with two pairs of rows, with four inches between the rows and eight inches between the pairs. Because of this, I decided on a 4" by 4" pattern.
An excellent introduction to woodworking is to use crates as your main material. The boxes are already formed, which means less assembly work for you—yet it looks impressive once your project is altogether. With this crate coffee table, you still get to practice your skills adding the casters and the center box. Finish with a little stain, and this table is ready to roll. You can find the full tutorial at DIY Vintage Chic. 

Though still straightforward in design, this bench distinguishes itself from many of its competitors with the sheer wealth of storage options. It includes two drawers of equal size with an additional drawer of double size as well as a spacious cupboard. Altogether, this provides for more storage space and organization than any other workbench we reviewed. Of course, this bench also comes with many of the same advantages and disadvantages that you would expect to see on other models within this lineup.
If you opt for a bench with drawers or cabinets built into its base, don’t forget the toe spaces: Leave a space roughly three inches deep and four inches wide at floor level for your toes, just like kitchen cabinets. The absence of a toe space means you’ll be forever kicking the face or sides of the cabinets which is irksome and, with tools in hand, potentially dangerous. And you’ll have to lean over farther to reach the back of the benchtop.
Still in the building mood? Get free woodworking plans to build greenhouses, barns, pergolas, garages, dog houses, potting benches, router tables, playhouses, cabins, tree houses, gazebos, porch swings, picnic tables, swing sets, deer stands, bookcases, home bars, wine racks, decks, work benches, chicken coops, bird houses, benches, and even homes.
With the Grain: A Craftsman’s Guide to Understanding Wood by Christian Becksvoort. A little knowledge about trees goes a long way toward improving your woodworking. You don’t need a degree in dendrology to build a desk. But you do need intimate knowledge of how our raw material grows and – more importantly – how it responds to its environment after it has been cut and dried.
If you're using drywall screws, you'll want to countersink the holes. Drywall screws are flat-head, and need a countersink to seat solidly. If you're using Kreg pocket screws, the way I did, you won't want to counter-sink the holes. Kreg screws are pan-head, and seat just fine against a flat surface. Both drywall screws and Kreg pocket screws are self-threading, so you don't need pilot holes in the second sheet of MDF.
AJ and Scott have been very helpful showing me where tools are my first few days there. This is a workshop where you will have to work independently. They will show you how to use certain machines for the first time and orient you to the shop itself but they will not help you with your project.  They can, however, be hired to help you with projects if that's what you need. I believe it's $75 an hour and limited to their availability. There is also a host of classes you can take if you want an intro into cabinet making, wood joining, turning etc. There are a lot of different classes that may pique your interests.

I had a similar experience with running electrical power to a shed. It turned out that I could build a 12x12 shed without a building permit as long as I did not run utilities, but getting a permit opened a whole new set of requirements that forbid me from having a shed at all. And when the nosey old woman next to me kept calling the building inspector on me, it was suggested that I could run an extension cord out to the shed anytime I wanted as long as it wasn’t fastened in a permanent manner.
×