What I did, when I came back, was to clamp down the strip where it had torn away, and then to start routing from the other end. I still moved the router from right to left, but I did it in six-inch sections, taking light passes, and sort of whittled the strip flush. As the sections I was working were farther to the right, the strip was thinner. Eventually I came to where I was trimming the strip away entirely, at which point I took off the clamps and the remainder fell away.

Still, one of the best features about this woodworking bench has to be its vices. First off, the Sjobergs provides two vices both as sturdily constructed as the bench itself. The same hardware that fastens the bench works to ensure the vices are just as strong. The next main benefit on the vices in the inclusion of multiple positions – four in total – for the vices to go. This allows you to mix and match to suit your needs and allows the table to be used just as easily by right-handed and left-handed users.
For the router you'll need a a 3/8" straight bit, an edge guide, 1/4"- and 1/8"-radius roundover bits, and a flush-trim bit with at least a 1-1/2" cutting length. Bits of this size are available only for a 1/2" collet. Some routers are capable of using multiple collet sizes. I was fool enough to buy a router that only had a 1/4" collet. More on that, later.
The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details. Follow the steps properly to make a nice and strong wall rack. This rack makes use of magnets to hold metal items. The tutorial explains the procedure for building this beautiful wall rack. Make sure to use only high quality items for any woodworking project. Use the rack only to hang items that are not too heavy for the magnet to hold. Also, be careful while working around this wall rack and beware of the knives falling off the rack.
In each Practical Woodworking Class, the daily mix consists of intensive lecture, demonstration, and student practice lab time.  Lecture periods are interactive, informative, and intensive but are also an enjoyable experience.  Generally, each joinery and fabrication process is demonstrated in several ways to reach or achieve the same results.  For example, processes are first demonstrated with the use of hand tools. Next, the same joint or procedure is done with simple hand held power tools (such as the router). Then, the entire process is demonstrated with stationary equipment such as the table saw, drill press, and mortiser. Students choose whichever production method works best for them and is in keeping with their plan to equip a home workshop and/or around their existing home tooling.
Though the preschool had been using the woodworking shop for storage, not realizing its historic value, it’s still in remarkably good shape. The woodworking benches and tables are still in excellent condition. According to Garrison, the shop is filled with clues as to how it was used. Some benches were covered in paint while others bear saw marks, testifying to the variety of tasks that were performed there.
Next is the shelf. Start with the 24x48" piece of MDF. Clamp this on top of the base, and pencil in the outside of the stretchers and the inside angle of the legs. Flip it over, pull out your trusty cutting guide, and cut it to width and to length. Cutting out the angles is simple, with a jig saw. It's not much work with a hand saw. If you took enough care with supporting blocks and stops, you could probably do it with a circular saw. Since I did have a jig saw, I used it.
You may even want to put yourself in the picture. If your workshop space already exists, find a large piece of cardboard, wallboard, or plywood that’s about the size of the workbench top you envision. Find a couple of stools or chairs, perhaps a few books, and turn them into stanchions to support the “benchtop.” Is it too big for the space? Is it large enough for the tasks you envision will be performed upon it?
The bench would end up being about 5 feet long. I thought about cutting 5 feet out of my 8 feet long countertop and use the rest for a small support table. However, after a consideration, I decided to bypass the front vise altogether together with the overhang so my bench will be 4 feet long. This allows me to skip the MDF and just glue the two halves of the 8 feet board together.
In this two day class we will reveal some of the secrets to tuning up a Japanese Hand Plane (Kanna) We will start with conditioning the Body of the Plane (DAI) to stabilize movement. Proper sharpening and grinding of the blade and chip breaker will be discussed and demonstrated. Custom fitting the blade to the Dai and conditioning the sole. We will...
Our Lexington model was designed to match many traditional New England homes, in Massachusetts and beyond. The steep pitch of the roof is built to withstand sometimes-punishing New England snow loads and complement today’s home design styles. Post Woodworking can match most vinyl siding colors, so that your shed color will coordinate with your home as well. And as is the case with all of our sheds, interior solar lighting is available to light up the night.
×