Synopsis: No room in the garage? Basement not an option? Consider what Ken St. Onge did when he needed shop space: He bought a prefabricated shed and converted it into his full-time woodshop. Because a pre-built shed doesn’t need a cement foundation and is built in a factory, it’s much less expensive than building an addition or stand-alone shop on your property. It can have taller ceilings than a garage and bigger doors than a basement, both big pluses for a woodworker. You can put a shed just about anywhere, too. Here’s a soup to nuts look at Ken’s experience, so you can gauge whether a shop in a shed is right for you.
If you don't quite have the space for a real pony, make this handcrafted wood version instead. The horse pictured here is unfinished pine, but there are lots of woods and finishes to choose from. Everything you need comes with the kit, and the plans can be downloaded. If you don't want to build it yourself, you can order from the website—just allow two to three weeks to ship.
Save money by selecting the right woodworking tools you need to purchase. You will have an excellent understanding of what tools, equipment and workshop features you need to get started in woodworking. By purchasing only the right woodworking tools and equipment you need, you will save money, allowing you to invest in higher quality tools and woodworking machinery.
Clamp the inner jaw of the end vise in position, leaving a little bit to trim off later, and then use the dowel and dowel center trick through the screw and guiide rod holes of the vise base plate to mark the position of the screw and guide rod holes in the jaw. Remove the jaw and drill 1-1/8" holes in the marked positions. I used the drill guide for most of the holes, and drilled freehand for the last bit. When you're starting a spade bit in a deep hole like this, start the drill very slowly, and the bit will move the drill into a perpendicular position. Start it too fast and the bit will bind and you'll damage the sides of the hole.
One you have the vise jaws shaped so that the vise moves freely, mark and drill holes in the fixed jaw for the bolts that will hold it to the bench. With these drilled, reassemble the vise and mark the location of the holes with an awl. Disassemble the vise and drill the holes through the stretcher, then reassemble the vise and bolt the inner jaw in place.
Flip the base upright, put the MDF on top of it, then use a straightedge to draw two straight lines joining the outside edges of the legs and extending the width of the MDF. I used the countertop as the straightedge. We cut it with our cutting guide, which is based on the factory edge of a sheet of 1/4" plywood, so it should be straight enough. Use a carpenter's square to transfer these lines onto the ends of the MDF.
Of course, I, on the other hand, with my Ikea oak countertop, probable went overboard in the other direction. Since I needed to trim the countertop to width,I figured I'd take off a couple of 1/2" strips to use for edging the MDF. I clamped the countertop to my bench base, and used the long cutting guide. I'd asked around for advice on cutting this large a piece of oak, and was told to try a Freud Diablo 40-tooth blade in my circular saw. I found one at my local home center, at a reasonable price, and it worked very well.
A bottle carrier is a bucket like carrier used to carry beer bottles and so. Yes, the same one you must have used to carry your six-pack. Drinker or not, a bottle carrier is a useful item for everyone. It can be used to carry around or store small items around a household. And it is also very easy to build one. I have several of these lying around my house. Also known as wooden beer totes, this is one wood item you will absolutely love to make. It is also super easy to build.
This is for the serious amongst you. Those of you who are ready to make a change in your life. To really surround themselves with woodworkers and furniture making for a whole year. Not only do you get to learn some great traditional skills but also drawing, the beginnings of design and how to run a woodworking business successfully. This intense workshop training gives you a good foundation to make your own way to become a furniture maker.
I agree that I might quickly outgrow a 12x8 shed. Lowes also offers a 12x10 Rancher (same style, but more room), but the 12x10 is 9 feet, 4 inches high, and my community only allows a maximum height of 9 feet. The 12x8 is exactly 9 feet high. I'm afraid of getting "out of spec" if I exceed the height limit and then getting in trouble with the Home Owner's Association. Having said that, 12x10 would be about the biggest size I could get for the available area in my back yard, so even if I hire a shed contractor to do this, the shed would have to be 12x10 or smaller.
×