I decided to make my own top out of white ash because I had access to a planer and jointer at my local college where I was taking an intro woodworking class. Trim and vice jaws are white ash as well. Everything else is built pretty much as jdege describes. A plunge router with a 3/4" spiral up bit really made quick work of the dog holes. Finished with Danish oil.
This place is great! They offer safety classes before you sign up for a membership, and the workspace is big and well maintained. I needed some basic lessons with table and band saws, which went great. I didn't ultimately get a membership because my sawing needs are very specific, and ended up getting a small bandsaw for myself at home. But if you're someone who needs the whole range of tools, this is the place to be!
The top is supported by the top ends of the legs and the top sides of the top stretchers. Stand your legs on end on a flat surface (like my door) and see if they wobble. If you have an end that isn't quite stable, use it as a foot, where the leveler will make it's flaws unimportant. Check the top edge of each stretcher for straightness. If one has a bit of a bow, use it for a lower stretcher. It's less critical that the shelf be well supported along its length.
I had a similar experience with running electrical power to a shed. It turned out that I could build a 12x12 shed without a building permit as long as I did not run utilities, but getting a permit opened a whole new set of requirements that forbid me from having a shed at all. And when the nosey old woman next to me kept calling the building inspector on me, it was suggested that I could run an extension cord out to the shed anytime I wanted as long as it wasn’t fastened in a permanent manner.
In 2006 Jonathan Schwennesen had an opportunity to begin an informal apprenticeship at the age of 17. He spent 4 years working as an apprentice in the Heritage School of Woodworking, learning the fundamental skills needed to build custom and speculative pieces of furniture. Next he began working for Homestead Heritage Furniture building custom furniture for different clients, gaining additional experience and knowledge making Windsor chairs, federal-style cabinets, clocks, workbenches, sleigh beds and even a waterwheel! It was during this time that he began to show an interest in teaching. Jonathan became a teacher’s assistant in 2009. He quickly began gaining the knowledge and skill to teach some classes himself. Now he spends most of his time working for the woodworking school. “My desire is to teach others an important aspect of life: working with your hands.”
Beyond the weight capacity, the Grizzly is also the largest table top on our list and in more ways than one. For a workspace, the Grizzly provides 5’ of length by 2 ½’ of width. There is not another table that really comes close to that size. Another size advantage of the Grizzly bench is the table top’s thickness. While the standard thickness of the table top for a quality woodworking bench is 1” with lesser models often offering only ¾” of thickness, the Grizzly provides a 1 ½” thick table top.
The 84-906 fits this bill perfectly as the table offers all of the qualities and features that you would expect but does not truly blow you away with any of them. For instance, this bench is made out of rubberwood. This wood is decent in that it provides the strength you want, but it is also extremely porous and rough-grained. The porous nature would generally make it susceptible to rotting and staining, though the bench has been lacquered. The rough grain will potentially cause tools to dull over time if you do not regularly relacquer it.
The Practical Woodworking course at the JD Lohr School of Woodworking is a complete and comprehensive woodworking course held in our shop on the 13-acre farm in southeastern PA. This is total immersion woodworking for ambitious, interested adults. With class size limited to 11 students and 3-4 instructors in each class, all needs of every student are met regardless of experience level. If you are self taught with no formal training as a woodworker, this course will quite literally change the way you work.
It doesn't get much better than a day at the woodshop! I've taken several classes from cutting boards to turning vases. It is always fun and informative! All of the machines are top notch and the instructors are great! I've toyed with the idea of a membership but I think I'll take a couple more classes before doing so! I can't wait to see the new location! :)
I mocked up the two scenarios, and determined that with the plate inside the stretcher the vise would have a reach of 8 inches, and with it outside the stretcher it would have a reach of 9 inches. I decided that 8 inches was enough, and that the extra inch wasn't worth the extra effort. With the end vise mounted like this, the right edge of the top would have no overhang.
A shed is a great project to earn your sawdust legs on. It is just some very basic carpentry skills. You could build the whole thing with a circular saw, hammer, utility knife, pencil, and tape rule. Find a friend or relative that has some decent skills to help. You could do it in a weekend. Keep the size on a four foot increment to minimize wastee. I would recommend a 12 x 12 or a 12 x 16 if you can. If you don't want to cut any rafters (which is really a simple process), you can order small triangle shaped trusses for the roof from your local lumberyard. If you are using T1-11 for the sides, get the real plywood based stuff, no waferboard. Same thing for the floor, use plywood (treated if you like). Cedar for the trim, not pine. The visqueen underneath is a good idea. Insulate the walls inside to help temper temperature swings. Build overhanges into the roof all the way around, 12" is nice. These really are a fun project. You can add a small window with a flower box underneath to make it look a little homey too.
Regardless of which type of screw you use, you'll need to flip the panel and use a countersink drill to on all of the exit holes. Drilling MDF leaves bumps, the countersink bit will remove them, and will create a little bit of space for material drawn up by the screw from the second sheet of MDF. You want to remove anything that might keep the two panels from mating up flat. I set a block plane to a very shallow bite and ran it over what was left of the bumps and over the edges. The edges of MDF can be bulged by by sawing or just by handling, and you want to knock that down.
I am sharing here a link to the detailed tutorial written by Pete at diypete.com, who shares the step by step process for making a wonderful barrel coffee table from scratch. He also tells you what items you’ll need for this project and where to find them. For example, you can buy an old whiskey barrel online or from a local whiskey store for a few bucks, if you haven’t already got one.
ALL Red Kits require planing and jointing of wood. Red Kits require the skill and tools to cut and make joints including panels. The woodworker needs to be able to cut, join, assemble and finish. Red Kits require the woodworker to be able to read the plans and to transfer images and dimensions from the plan to the lumber. It supplies all of the needed hand-selected, dimensioned lumber but woodworking knowledge and tools are recommended to be successful with Red Kits.
Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.

I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.


I like the idea of re-inventing the wheel. I choose to believe that while others may have considered these improvements, they just never got around to trying them out. Brain gets bored with status quo. So, I try to keep Brain happy with the occasional foray into uncharted territory. And I must say Brain has had some really good results. Thanks, in part, to you, and the Roy. You never know where a good idea might come from so I’ll check in once in a while. That and make sure to build it in Sketchup first.
The holes we want to mark are the holes through which the threaded rod connecting the two legs will run. This threaded rod will run through the 3/8" groove along the bottom of the short stretchers,. The hole for the upper stretcher has to be positioned so that when the rod is running through this groove, the top of the short stretcher is even with the top of the legs. The most precise way I've found for marking the position of this hole is to use a dowel center. Fit the dowel center into the bottom groove, line up the stretcher, and bang on the end with a rubber mallet. The dowel center will leave a mark indicating the center of the hole.
In the Port Townsend School of Woodworking’s twelve-week Woodworking Foundation course, you will learn the essential skills, tools and mindsets of the traditional joiner. This is NOT an industrial arts course with a focus on machinery and production processes. Rather, it is a course in PRE-industrial artisanship--the creation of individual works through mostly hand tools and skills.. 
Right now, there is a revolution in woodworking courses created by the closure of many state-run colleges. Our workshop has led the way and been the model for many of the private furniture making courses available to you today. Rowden Atelier is recognised as a Centre of Woodworking Excellence that produces exceptional furniture and trains exceptional woodworkers. With our range of specialist woodworking courses, you could be one of them.
Right now, there is a revolution in woodworking courses created by the closure of many state-run colleges. Our workshop has led the way and been the model for many of the private furniture making courses available to you today. Rowden Atelier is recognised as a Centre of Woodworking Excellence that produces exceptional furniture and trains exceptional woodworkers. With our range of specialist woodworking courses, you could be one of them.

The decision to be made with respect to the end vise is whether the support plate should be mounted to on the inside or on the outside of the stretcher. Mounting the plate on the inside of the stretcher reduces the reach of the vise - it can't open as far, because the support plate is back from the edge by a couple of inches. But mounting the plate on the outside of the stretcher means that we need to add some support structure for the inner jaw of the vise, which the legs would have provided if we'd mounted the plate on the inside.
The end vise will have both jaws made out of 1-1/2" thick oak. The front vise has its moving jaw made of 1-1/2" oak, but uses the edge of the bench as its stationary jaw. So while for the end vise, if we mount it lower, we can make both the jaws deeper to compensate, for the front vise we cannot, so we want it mounted as close to the edge of the bench as possible.

When you have the other leg seated, the threaded rods will extend father than you want them to. You'll want to mark them so they can be cut to length. Place a washer and a nut on each threaded rod, and then tighten down the nut to pull everything tight. Depending upon the wrench you are using, and how much longer the rod is than it needs to be, you may find it necessary to stack up a number of washers, so that the nut is positioned where the wrench can operate on it.
Through demonstrations and practice you will learn how to build a Simple Table Top. Square wood using the Jointer, Planer and Table Saw, then learn how to use the Festool Domino Joiner to keep perfect registration during the glue up. This will be a group project where everyone will help build a single table top. The goal is to gain experience and confidence...
While a strict figure for the bench’s weight capacity is not available, a quick browse through their other stand and bench products shows a general weight capacity well above most other brands. As such, while we cannot say for certain that this bench provides the best weight capacity, it is more than likely that it the capacity is similar to the other products in the catalog.
After I left the magazine for a new job, I did all of my woodworking in my small two-car garage, but it was a struggle. Power, lighting, and temperature control were limited. And because I shared space with our cars I was always moving machines around, often while in the middle of a project. On top of that, my tool and machine collection had long since eclipsed the space. For all these reasons, fixing up the garage wasn’t an option. My finished basement is a family room, so it was out, too. An addition to the home or a stand-alone building would have been too expensive. I had to find a better path to a shop.
×