The jaw for the front vise needed to be 10" long - to span the distance from the leg to the end of the top, 1-1/2" thick - to allow for benchdog holes to be drilled in it, and 5" tall. The end vise was mounted 3/4" lower than the front vise, and the screw and guide rods were thicker, so its jaws needed to be at least 6-1/2" tall. Again, they needed to be 1-1/2" thick to allow for benchdog holes, and 23" long to span the width of the bench.

A steam box and a heat source are the two main components used to steam bend wood. Steam boxes must be able to withstand large fluctuations in temperature and humidity without breaking apart. In this two-hour workshop, students will build an optimized steam box that can last through the tough job of steaming wood, allowing them to continue creating their own projects at home!


I decided to make my own top out of white ash because I had access to a planer and jointer at my local college where I was taking an intro woodworking class. Trim and vice jaws are white ash as well. Everything else is built pretty much as jdege describes. A plunge router with a 3/4" spiral up bit really made quick work of the dog holes. Finished with Danish oil.
Working with reclaimed wood is a savvy use of resources, and the material's country appeal is undeniable. With just a saw and a small drill, you can reuse old fencing to make these simple woodworking projects: picket-inspired picture frames. Finish them off by hot-gluing clothespins or bulldog clips to hang your prints. Here’s a step-by-step guide.
Building a Wooden Office Desk Organizer is an easy task for a professional woodworker, but not so much for normal people like you and me. But that doesn’t mean you cannot do this. Two years ago, I had almost no woodworking experience, but now I make most of my household and office wooden items by myself. This saves me a lot of money. And believe me when I say this; you can also manage to make wonderful wood items with a little practice and some woodworking experience.
All-in-all, the Windsor Design workbench is a nice companion, especially if your budget is limited. It is not as deeply designed and perfected as the other two benches, as there is only one vice, the bench dog holes are drilled through the surface (allowing debris to fall to the top drawers) and the drawers can be a little flimsy if you are not using glue for assembling it, but for the price they offer, there are plenty of perks.
When you're working with linseed oil, never -- I mean NEVER -- leave used rags lying around. Hang them up outside, away from anything combustible, and where there's enough air circulation to keep them cool. Or put them in a bucket of water, and hang them outside later. If you're just setting a rag down for the moment, set it out flat, without folds, on something non-flammable. Hanging outside in the breeze, the oil in the rags won't retain heat while they oxidize. For the oil to completely oxidize can take in a couple of days, if it's warm, or more than a week, if it's cold and rainy. When fully oxidized, the oil will be solid and the rags will be stiff. At that point, they're safe, and can be thrown in the trash. Toss them in the trash before that, and you might as well say goodbye to your garage.
Though the preschool had been using the woodworking shop for storage, not realizing its historic value, it’s still in remarkably good shape. The woodworking benches and tables are still in excellent condition. According to Garrison, the shop is filled with clues as to how it was used. Some benches were covered in paint while others bear saw marks, testifying to the variety of tasks that were performed there.
This bench suffers from no such limitations as it provides an incredibly solid and stable workspace, albeit in a somewhat stripped down version. In terms of performance, Sjobergs tops our list at providing 80 lbs of weight capacity. This is one of the more quantifiable measurements to determine the quality of a work bench’s craftsmanship. This is achieved by using thick pieces of European birch wood and working it without using lower end joints – like butt joints.
@cahudson42 I bored the holes in my sandwich top with a 3/4" power auger bit with the drill in a portable drill guide that kept it vertical and in a way a bit like a plunge router. The guide screw of the auger was dead easy to centre over the laid out grid points. The holes are dead straight and clean sided. The auger bit was new which probably helped. As stated I have three rows from an end vise running the length of the front as well as from the front vise and holes in the front apron to support long pieces as well.
I never, ever, ever bother to write these things. But, I am so incredibly impressed with this product, that I feel compelled to. My six year old daughter LOVES IT, as does my almost four year old daughter. The hammer is just the right size, and it comes with enough pre-cut (good quality) wood for many projects. So far, they have made a house, car, and a plane-- all of which are far more aesthetically pleasing (to me, as a mom) than the plethora of junky plastic toys that seem to fill our home. We've used these projects both as math lessons (measuring the wood, counting the nails needed, learning about angles, reviewing shapes) and during arts & crafts time; but, with just a little creativity, they could be incorporated into just about any learning subject. For the amount of enjoyment we have received, thus far, this product is already worth the money spent, and we have several more projects to go! We will be buying another for little sister's upcoming birthday, most definitely.

Palomar Community College in San Marcos, located about 35 miles north of San Diego, offers certificate, degree and life-long learning programs to more than 20,000 students a year. In particular, the Cabinetmaking and Furniture Technology Department offers in excess of 50 classes annually, and the present faculty is composed of four full-time teachers, 21 part-time instructors and 11 teaching assistants. As of Fall 2013, woodworking students will have access to a newly remodeled woodworking facility equipped with three machine rooms, three bench rooms, a saw mill and a finish room.


Linseed oil sitting in a bowl, or spread on the surface of wood, is perfectly safe. But a linseed oil soaked rag provides a vastly increase surface area, so the oxidation happens faster, and the rag can provide insulation, trapping the heat. The increased temperature speeds up the oxidation even more, which raises the temperature even more, and the runaway feedback can quickly result in temperatures that will cause the rag to spontaneously burst into flame. This isn't one of those "do not drive car while sunscreen is in place" warnings. This is one of those "keep your finger off the trigger until you have the gun pointed at something you want to shoot" warnings. Rags soaked in linseed oil will catch fire, if you don't handle them properly, and they can do so far more quickly than you might think.
I am sharing here a link to the detailed tutorial written by Pete at diypete.com, who shares the step by step process for making a wonderful barrel coffee table from scratch. He also tells you what items you’ll need for this project and where to find them. For example, you can buy an old whiskey barrel online or from a local whiskey store for a few bucks, if you haven’t already got one.
The decision to be made with respect to the end vise is whether the support plate should be mounted to on the inside or on the outside of the stretcher. Mounting the plate on the inside of the stretcher reduces the reach of the vise - it can't open as far, because the support plate is back from the edge by a couple of inches. But mounting the plate on the outside of the stretcher means that we need to add some support structure for the inner jaw of the vise, which the legs would have provided if we'd mounted the plate on the inside.
TOH has showed you how to make a toy chest with your kids before, but if you don't feel like cutting the wood yourself, opt for a kit like the one for this beautiful cherry chest. The kit comes with pre-cut pieces and all the hardware you need. Like many toy chests out there, the closed lid can also function as a bench seat, and the hinges are designed to prevent little fingers from getting caught. This model is available in three different finishes.
For the router you'll need a a 3/8" straight bit, an edge guide, 1/4"- and 1/8"-radius roundover bits, and a flush-trim bit with at least a 1-1/2" cutting length. Bits of this size are available only for a 1/2" collet. Some routers are capable of using multiple collet sizes. I was fool enough to buy a router that only had a 1/4" collet. More on that, later.
2 - use a plunge router with a bottom bearing cuter bit such as this from rockler: http://www.rockler.com/product.cfm?page=25160&site=ROCKLER .... I thought to use the short one as I plunge it directly downward in the centre of the hole until the bearing reaches within the tabletop hole. I suppose one could use a long one, but the stubbiness seemed more practical (the big bearing ensured accuracy?)
The beauty of this project lies in the simplicity. All you need are 3 pieces of wood of your choice (though we must admit natural hardwoods will look incredible), sanding block, clamps, wood glue and finishing product. The hardest step of the whole tutorial is measuring – as always, measure 9 times, cut once! You wouldn’t want to finish your project and then realize it doesn’t have enough space to fit your DVD player, would you?
In this two day class we will reveal some of the secrets to tuning up a Japanese Hand Plane (Kanna) We will start with conditioning the Body of the Plane (DAI) to stabilize movement. Proper sharpening and grinding of the blade and chip breaker will be discussed and demonstrated. Custom fitting the blade to the Dai and conditioning the sole. We will...
I’ve built workbenches with more than 100 students. In every class, there’s one guy who wants to put a vise on every corner of the bench. Not because it’s a partner’s bench for two people. Just because he wants it that way. While I support your freedom to choose, I also don’t want to spend two weeks installing complex tail-vise hardware on your bench when we could be building furniture instead.
Although many hand tool operations are thoroughly covered, this is a machine based woodworking experience. You will find the school finely equipped with four table saws, four jointers, three drill presses, three thickness planers, a wood lathe, full dust collection, bandsaws, jig saws and scroll saws, 5 routers and dozens of router jigs and accessories. There is a heavy focus on the safe and efficient use of the table saw starting with it's basic operation and going into advanced production procedures. We consider the table saw to be an essential machine for efficient, accurate, and safe woodworking.
Building a Wooden Office Desk Organizer is an easy task for a professional woodworker, but not so much for normal people like you and me. But that doesn’t mean you cannot do this. Two years ago, I had almost no woodworking experience, but now I make most of my household and office wooden items by myself. This saves me a lot of money. And believe me when I say this; you can also manage to make wonderful wood items with a little practice and some woodworking experience.
Foundations of Woodworking runs every fall (September - December) and winter (January-March). The application process for each session opens 9 months in advance of the course start date. Applications will be considered for registration in the order in which they are received. There is no fee for applying. Accepted applicants will be invited to register. We ask for a deposit of $200 at the time of registration to ensure your place in the class. 
Foundations of Woodworking runs every fall (September - December) and winter (January-March). The application process for each session opens 9 months in advance of the course start date. Applications will be considered for registration in the order in which they are received. There is no fee for applying. Accepted applicants will be invited to register. We ask for a deposit of $200 at the time of registration to ensure your place in the class. 
The first time you try your hand at the ancient craft of woodworking, you want to do it right. Learn woodworking basics with hand tools to a professional standard on a weekend woodworking course at Rowden Atelier. Ed Wild runs weekend furniture building courses for everyone from beginners who want to have some fun experimenting behind the bench, to those who are looking to develop specific skills as a furniture maker. Classes include tool handling, box making, and basic veneering, but to a certain degree, you can tell us what you want to learn - these short woodworking courses are partly bespoke.

The right shed for your home will depend on your desired use. Utility bins are ideal for storing trashcans and recycling bins out of sight. Patriot sheds are ideal for sporting equipment, riding mowers, snowblowers, and other small vehicles and heavy tools. If you want a workshop with storage to spare, look into the Elite line of products. With creative small-space storage solutions, any one of our sheds can truly increase the usable space in your home.
A woodworker's Workbench is a special type of bench designed to hold your work when you are working on a wood project. The main purpose of this table is to keep the woodwork steady and to prevent it from moving. Follow the tutorial below to build yourself a nice workbench suitable for your specific woodworking projects. Make sure to modify the table to fit your specific requirements.
A couple nice qualities about this bench include the weight and vice capacities. The weight capacity of this bench is 330 pounds which is decent, though it will not wow you too much. The vice, on the other hand, provides a 7” capacity which is tied for the most on our list. That said, there is only a single vice, and it is not able to be repositioned. This can make things a bit frustrating for lefties as it is a right-handed configuration.
Get perfectly, consistently spaced and centered shelf-pin holes! Economical and practical, this jig can be used on assembled or unassembled cabinetry. Re-designed handle includes two storage compartments for self-centering bits! Ideal for adding shelves to new or existing cabinets. Drills holes either 1-7/16" or 2-1/2" from edge. Insert shelf pin in top or bottom position to extend jig for continuous drilling. Shelving Jigs measure 20" long Additional Self-Centering Bits available. 
Flip the base upright, put the MDF on top of it, then use a straightedge to draw two straight lines joining the outside edges of the legs and extending the width of the MDF. I used the countertop as the straightedge. We cut it with our cutting guide, which is based on the factory edge of a sheet of 1/4" plywood, so it should be straight enough. Use a carpenter's square to transfer these lines onto the ends of the MDF.
The book is well written and easy to read. The illustrations, I'm sure were excellent in 1914 and, are still adequite now. Most of the designs seemed repetitive, though. I wish more attention had been given to lashing materials. If you are looking for that you will find almost none here. The book was fun to read and provided enough inspiration to make my brother and me attempt a large hut.
×