I'd intentionally made it oversize, intending to trim it flush. Trimming is a little more complicated than usual, because I needed to trim it flush on two faces. The end face extended a good 3/8", so I cut off most of the excess with a circular saw and the edge guide, then flipped the edge guide upside down to make a stable platform for the router. Aside from the use of the edge guide, flush trimming the edge face was unremarkable.
Those bums even have a stipulation that you can't connect any utilities to a shed. My plan is to adhere to the letter of the law if not the spirit. I plan to run a buried 20 amp power line out to the shed (this will be done professionally and properly according to whatever is required by the law), but it will require a manual connection to a junction box on the outside of my house to complete the circuit. That way, I can argue that the electrical connection is only temporary and is little more than a safe and buried version of an extension cord.

Remove the jaws and route the edges that you could not route while they were still attached. Then use a roundover bit on all of the corners except the inner edge of the inner jaw of the end vise. Give everything a lite sanding, and apply Danish oil to the inner surfaces of the jaws. (By "inner surfaces", I mean those surfaces that will not be accessible when the vises are assembled - the inner surface of the inner jaw, that bolts to the bench, and the outer surfaces of the outer jaws, that bolt to the vise plates.)
The Meridian 8 ft. x 10 ft. wood The Meridian 8 ft. x 10 ft. wood storage shed kit from Handy Home Products is pre-cut and easy to assemble with common household tools. It features 9 ft. peak wall height with treated engineered siding that prevents rot and is pre-primed and ready to paint (paint sold separately). The ...  More + Product Details Close
A better solution would have been to route a rabbet into the side, so that the added strip always had thickness. The way I did it means that the strip I glued in is very narrow, and hence very weak, at a certain point. In this case, that's not a problem, because it's going to be sitting under the countertop layer. I also noticed that because I had only clamped the strip down, and not into the edge, there was a noticeable glue gap where the strip butted up against the MDF. Again, in this application it isn't visible. But if I was doing something like this on the top of a table, I'd make sure to cut a clean rabbet, and to clamp both down and in.
Woodworking Workbenches are available in a variety of styles. Open Style Wood Workbenches feature a large work surface and a lower shelf. 2-1/4" thick maple top with maple plywood lower shelf. Open Style Wood Workbenches are available as a 2-station unit (28"W) or a 4-station unit (54"W). Open Style Auxiliary Workbenches are used for placement against walls. Shelf features a rear curb to keep contents in place. Solid maple top features angle iron front edge. Plywood shelf is open for maximum functionality. Solid maple legs. Environmentally-friendly UV finish. Units measure 24"D and are available in several lengths and heights. Mitre Box Benches ensure wood pieces are kept flat while mitres are cut. Bench is made using solid maple unit with environmentally-friendly UV finish. Holds a mitre saw up to 26"W and provides a 24" square work surface on both sides. Mitre Box Benches measure 33-3/4"H. Sheet Metal Workbenches are made with a 2-1/4" thick maple top and is protected on two long edges with 2" x 2" angle iron. Solid maple legs and stringers. Plywood shelves are designed to provide open storage of 30" metal sheets. Measures 40"D x 32"H and available in widths of 60" or 96".
Isn’t this amazing that instead of having to throw that old furniture piece away, you can now reuse it to build something even more beautiful? If you do not like this particular idea, there are many other re-purposeful furniture items you can build from an old dresser. Just search the internet for other DIY project ideas. Here is a link to the video tutorial that explains the same procedure in a more practical manner that you can easily follow through.

The holes we want to mark are the holes through which the threaded rod connecting the two legs will run. This threaded rod will run through the 3/8" groove along the bottom of the short stretchers,. The hole for the upper stretcher has to be positioned so that when the rod is running through this groove, the top of the short stretcher is even with the top of the legs. The most precise way I've found for marking the position of this hole is to use a dowel center. Fit the dowel center into the bottom groove, line up the stretcher, and bang on the end with a rubber mallet. The dowel center will leave a mark indicating the center of the hole.
The right shed for your home will depend on your desired use. Utility bins are ideal for storing trashcans and recycling bins out of sight. Patriot sheds are ideal for sporting equipment, riding mowers, snowblowers, and other small vehicles and heavy tools. If you want a workshop with storage to spare, look into the Elite line of products. With creative small-space storage solutions, any one of our sheds can truly increase the usable space in your home.

After you have all the holes clean, set things up for your glue-up. You want everything on-hand before you start - drill, driver bit, glue, roller or whatever you're going to spread the glue with, and four clamps for the corners. You'll need a flat surface to do the glue-up on - I used my hollow core door on top my bench base - and another somewhat-flat surface to put the other panel on. My folding table was still holding my oak countertop, which makes a great flat surface, but I want to make sure I didn't drip glue on it so I covered it with some painters plastic that was left over from the last bedroom we painted.
In class, each student will build a detailed hall table that is complete with mortise and tenon joinery, biscuit, dowel, and floating joint construction.  The student project is presented with a variety of design options and formats as to meet the experience and comfort level of each student.  Depending on their experience and comfort level, students are encouraged to make a simplified version of the hall table or tackle a more sophisticated and complicated version of the same project. Your only limitation is the amount of material you receive in your lumber pack (~24 board feet).

Thanks! Great information. As an advanced novice worker, I finally decided to build my first bench a couple years ago. After reading several of your blogs knowing full well mortised dove tale leg joinery is yet beyond my capability, I elected to build Robert Lang’s “21st Century Workbench”. I also chose his VERITAS Twin Screw Vise in the face vise position. Used an old Craftsman face vise in the tail vise position. Constructed of laminated 9/4 x 31/2″ Pecan and 60″ long because of my small crowed shop. Super happy to this point. As I mature in woodworking I may live to construct one of a different choice at a latter date, but I’m 73 so we’ll see. Thanks again for the advise.


I am blown away with their ability to teach, a rare characteristic in my opinion, even more so is their passion to do so. I feel that they are able to accurately depict the philosophies and ideas mentioned in your website. My expectations did not even come close to the actual experience I have been given, and that is only in a short short time! I can only dream of what the next 11 months will bring! I am convinced my decision to study at Rowden Farm is the best one I have made to date! Thank you! Much appreciation and gratitude!”
Looking for new ideas for your woodworking projects? Good news! We’re here to help you come up with astonishing yet easy to do wood crafts. Everybody who’s into woodworking knows its benefits. The satisfaction that we feel every time we build something out of wood and turn it into a beautiful piece of art is truly priceless. To some, working on a woodcraft is both relaxing and gratifying. To other craftsmen, it can be a good source of profit. So scroll down and find out some woodworking ideas that can help you create a new useful masterpiece.
All glue & stain benches are made using a solid maple frame for lasting durability and strength. Side Clamp Benches are made specifically for bar clamps, and are used for gluing projects or clamp storage. Benches feature an open top with 17 sets of 3/4"W grooves that accept bar clamps measuring 3’ and over. Lower center rail is adaptable for storage of hand screws and C-clamps. Side clamp benches are available with or without a drip pan. Glue & Stain Benches are made with a 1-1/4” plywood top covered with heavy-coated galvanized steel. Bottom shelf has a 4” rear retaining lip. Glue and stain benches are available with or without casters. Limited Lifetime Warranty.
The Handy Home Products Berkley 10 ft. x The Handy Home Products Berkley 10 ft. x 16 ft. Do-It-Yourself Wood Shed Kit Combines charming country style and outstanding performance for the ultimate powerhouse. Offering maximum storage this woodshed is the ideal solution to house all your outdoor tools and lawn gear. Featuring 2x4 wood framing it boasts a ...  More + Product Details Close
Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.
I was using 2-1/2" coarse Kreg pocket hole screws. Kreg screws are supposed to be self-tapping, but the coarse-thread screws are intended to be self-tapping in softwood, and the fine-thread screws they intend for use in hardwoods aren't available in 2-1/2" lengths. I decided to drill pilot holes in the oak. Just to make sure, I did a test hole in the scrap piece I'd cut off.
I live in the second rainiest city in the country, Pensacola, so I am used to dealing with wet. I literally work out of my garage (read storage area, small woodwork area, washer/dryer...car? ). I wheel bigger tools and table out to the little covered area in front of the garage. I have an 8 x 10 aluminum shed that is strictly garden stuff storage. I mention this for two reasons.
×